6PMVision Backup Dialog | Lucent Technologies Network Access Module

Selecting PMVision Functions

Figure 6-6PMVision Backup Dialog

Restore the INA Module Settings

To restore the INA module settings captured in a backup file, select

INA→ Maintain→ Restore. Enter or browse to the backup filename on the Restore panel (Figure 6-7)and click Restore. The restored values overwrite any values existing in the INA module. A backup file created with a selective backup overwrites only the selected configuration values and leaves the others unchanged.

Figure 6-7PMVision Restore Dialog

6-8	INA Module Installation and Configuration Guide

Page 48

Image 48

Lucent Technologies Network Access Module manual Restore the INA Module Settings, 6PMVision Backup Dialog

Contents

Merlin Magix Your Responsibility for Your System’s Security Year 2000 Compliance Copyright and Trademarks Page Contents Contents Using the INAWizardUsing the Command Line Interface Using PMVision TroubleshootingCable Specifications Merlin Magix Administration Index Viii Safety Instructions Important Safety Instructions -SAVE These Instructions Important Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix Documentation Calling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, Release PortMaster Documentation Additional References Document Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold font Limited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. Call Subscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin Magix On the INA Module INA Front PanelINA Front Panel 1INA Module Front Panel INA Module Installation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI Provisioning Network Settings Network SettingsAssign T1/PRI Channels Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33 Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough Cable Set DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect Cables Installing the INA Module Connect a Console OptionalConnect a T1/PRI Cable Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED Behavior System LED System LED Ethernet LEDs 8Ethernet LEDs Using the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LAN Run the Wizard Using the Command Line Interface Using the C0 Console PortConnect a Console Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password Log Command set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and Netmask Set the Default Route Gateway Command set sysname StringSet the System Name Set the System Name Configure the WAN Port Set the Name ServiceSet the Name Server Set the Domain Name Set Up Additional WAN Ports Set the Channel RateSet the Port IP Address Optional Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port Optional Configure the WAN Port Using PMVision Install PMVision Using a Crossover Cable Run PMVisionRun PMVision Using PMVision Communicate with the INA ModuleCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision Functions Enter Basic Settings Working with Configuration DisplaysSave Edit Edit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ Global Using the Backup and Restore Functions Back Up the INA Module Settings Restore the INA Module Settings 6PMVision Backup Dialog Troubleshooting a LED Behavior Possible Cause SolutionObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screen Error at failed Field Possible Message ExplanationMemory address Address Using the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test Jacks Test Jack Label Description and Usage Figure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console Cable Ethernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI Cable RJ-45 Connector Crossover CableCrossover Cable Crossover Cable Merlin Magix Administration INA Module Administration OptionsINAModule System Programming Summary INA Module Administration Options Activate or Deactivate the Onboard CSUDSU Channel Selection INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection Description INA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals Description Clearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current Events Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback Test Backup and Restore INA Module System InteractionsSurrogate Operation Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System Interactions Replacement Condition Explanation System EraseFrigid Start System Restart INA Module System Interactions Index Index-1 Index Index-2 Index-3 T1/PRI Index-4 Index-5