Configuring bridging | Nortel Networks 8683POS specification

62Chapter 4 Managing the Passport 8683POS Module

5Select the SonetClockSource, either line or internal.

If two Passport POS Modules are operating directly (that is, connected back to back, without any intervening Sonet equipment), one port must provide the clock source. Set the clock source of one port to internal, and the opposite port must be set to line.

6Select other SONET parameters.

7Click Apply.

8Re-enable the port as described in “Enabling or disabling a port” on page 59.

Configuring bridging

The Passport 8683POS Module is configured for bridging by default. The configuration is set for bridging between two Passport 8683POS Modules with one default VLAN. The Bridge Control Protocol (BCP) is enabled on the Passport 8683POS Module by default.

Note: When the POS link is enabled after a parameter change or a chassis reset, some superfluous traffic may initially be sent out of POS ports before any LCP packets go out. This is normal.

You can also configure bridging for the Passport 8683POS Module for connection to other POS-capable devices.

209564-A

Image 62

Nortel Networks 8683POS manual Configuring bridging

Contents

Using Passport 8683POS Module Statement of conditions Copyright 2001 Nortel NetworksTrademarks USA requirements only Taiwan requirements Using the Passport 8683POS ModuleJapan/Nippon requirements only Canada requirements only 209564-A Using the Passport 8683POS Module 209564-A Contents Chapter Installing the Passport 8683POS Module Contents Chapter Graphing statistics in Device Manager Chapter Web management Figures Figures Tables 103 Tables Tables 209564-A Preface Before you begin Text conventions Italic text Related publications How to get help Preface 209564-A Chapter About the Passport 8683POS Module Features About the Passport 8683POS Module Physical description PPP over Sonet RFC Media dependent adapters Shows the OC-12c/STM-4 MDA, and shows the OC-3c/STM-1 MDA Online LED Passport 8683POS Module online LED indications Lists the MDA LED indications MDA LEDsConsole and Diag ports MDA LED indications Chapter Using the Passport 8683POS Module Sonet transmission Sonet terms and acronyms SONET/SDH transmission rates Single-mode fiber SMF Multimode fiber MMF Point-to-Point ProtocolEstablishing the PPP link Using the Passport 8683POS Module Spanning tree group feature Negotiating network layer protocols Using the Passport 8683POS Module 209564-A Chapter Installing the Passport 8683POS Module Safety and environmental precautions Installing the Passport 8683POS Module Installing the Passport 8683POS Module Removing the filler panel Extending the inserter/extractor levers Closing the inserter/extractor levers MDA1 Tightening the retainer screws MDA1 Verifying installation Initialization Redownload requested by POS card in slot number MDA insertion and configuration Starting the system with an empty slot Starting the system after a module replacementReplacing a module Installing the Passport 8683POS Module 209564-A Chapter Managing the Passport 8683POS Module Port numbering Device Manager Managing the Passport 8683POS Module Passport 8683POS Module access levels Device Manager access and passwordsInstalling Device Manager Managing the Passport 8683POS Module Passport Device Manager port color codes Passport Device Manager buttons Resetting the module Card tab Card tab fields Describes the fields in the Card tabClick the POS tab POS tab opens Figure POS tab fields Viewing MDA informationDescribes the fields in the POS tab MDA dialog box fields Command line interfaceDescribes the fields in the MDA dialog box Passport 8683POS Module default settings Configuration proceduresDefault configurations Basic procedures Port dialog box Interface tab 209564-A Describes the Interface tab items Interface tab items Managing the Passport 8683POS Module Interface tab items Sonet parameters Enabling or disabling a port Port dialog box POS Sonet tab 209564-A Describes the items in the POS Sonet tab POS Sonet tab items Configuring bridging Configuring routing Configuring IP routing using Device Manager Port dialog box POS PPP tab 209564-A Describes the POS PPP tab items POS PPP tab items Describes the fields in the IP Address tab IP Address tab fields Describes the Port, Insert IP Address dialog box items Configuring IP routing using the CLITo disable bridging, enter Insert IP Address dialog box items Configuring IPX routing using Device Manager To configure IP routing, enter Basic tab fields Vlan dialog box opens with the Basic tab displayed FigureDescribes the fields in the Basic tab Managing the Passport 8683POS Module Basic tab fields To configure IPX routing, enter Trap featureConfiguring IPX routing using the CLI Click the Trap Receivers tab Trap Receivers tab opens Figure Trap Receivers tab fields Describes the fields in the Trap Receivers tabDescribes the fields in the Insert Trap Receiver dialog box Insert Trap Receiver dialog box fields Trap Log dialog box fields Viewing the Trap LogDescribes the fields in the Trap Log dialog box Sonet loopback test feature Describes the Test tab items Managing the Passport 8683POS Module Test tab items Alarms Passport 8683POS Module alarms Managing the Passport 8683POS Module 209564-A Overview This chapter contains information on the following topics Displaying statistics Graphing statistics in Device Manager Types of statistics Viewing POS statistics Graphing statistics in Device Manager Viewing PPP Link statistics Graphing statistics in Device Manager POS tab fields Describes the fields in the PPP Link tab PPP Link tab fields Viewing PPP LQR Describes the fields in the PPP LQR tab Viewing Section statistics PPP LQR tab fields Describes the fields in the Line tab Viewing Line statisticsDescribes the fields in the Section tab Section tab fields Viewing FE Line statistics Graphing statistics in Device Manager Line tab fields FE Line tab fields Viewing Path statisticsDescribes the fields in the FE Line tab Path tab fields Viewing FE Path statisticsDescribes the fields in the Path tab Describes the fields in the FE Path tab FE Path tab fields Chapter Command line interface This chapter contains the following topics Command line interface Configuration commandsConfig poscard commands Config poscard command parameters and variables Port commandsConfig pos command Config pos ip Enabled with the command config sys set portlock on Config pos ppp Config pos ip command parameters and variables Config pos sonet command Config pos stg command Config pos info command Config pos stg command parameters and variables Show commands Show ports info pos Show ports info pos all Show ports info pos all command output Port POS S/W PLD Framer Card NUM Version Port NUM Show ports stats pos activealarms MRU Show ports stats pos activealarms command output Show ports stats pos felinecurrent Show ports stats pos felinecurrent command output Show ports stats pos felineinterval command output Show ports stats pos felineinterval Show ports stats pos fepathcurrent command output Show ports stats pos fepathcurrent Show ports stats pos fepathinterval Show ports stats pos fepathinterval command output Show ports stats pos linecurrent command output Show ports stats pos linecurrent Show ports stats pos lineinterval Show ports stats pos lineinterval command output Show ports stats pos linkstatus command output Show ports stats pos linkstatus Show ports stats pos lqrstatus command output Show ports stats pos lqrstatus Show ports stats pos pathcurrent command output Show ports stats pos pathcurrent Show ports stats pos pathinterval command output Show ports stats pos pathinterval Show ports stats pos pppiftbl Show ports stats pos pppiftbl command output Show ports stats pos sectioncurrent command output Show ports stats pos sectioncurrent Show ports stats pos sectioninterval Show ports stats pos sectioninterval command output Show ports stats pos sonetmediumtbl command output Show ports stats pos sonetmediumtbl Show tech command Show tech command has the following syntax Show tech command output Monitor commands Test commands Leds Test hardware Using the test commandsOutput from the test hardware command is shown in Figure Test led Off Test led command parameters and variablesTest loopback Yellow Shows output for the test loopback command Chapter Web management POS folder Describes the fields displayed in the System Web management System page fields System page showing the POS menu Describes the fields displayed in the Sonet Sonet page fields Describes the fields displayed in the Link Link page fields Describes the fields displayed in the Bridge Bridge page fields Describes the fields displayed in the IP Describes the fields displayed in the IPX IPX page fields Describes the fields displayed in the Lqr Lqr page fields Describes the fields displayed in the Line Line page fields Describes the fields displayed in the Sonet Medium Sonet Medium page fields Statistics Sonet options PPP Link statistics 209564-A Appendix a Technical Specifications Appendix a Technical Specifications Environmental specifications Electromagnetic Appendix a Technical Specifications 209564-A Index Index Index 104 Index Index 209564-A