Panasonic AG-HPX600EJ, AG-HPX600EN, AG-HPX600P [SETUP] screen, [TCG], [RST], [UBG], [RST], Screen, [TC_MD], [R‑RUN], [TC/UB], [TC_MD], [TC/UB], <COUNTER, [0] to [9], mode exits, mode exits, SET01:TC/UB

		Chapter 8 Using SmartUI — Menu list
[SETUP] screen
Screen	Corresponding button	Setting details and setting value
SET01:TC/UB	Sets the time code or user bits.
	When an item other than [UB] is selected for the counter display on the [HOME] screen, the time code setting screen appears, and when
	[UB] is selected on the [HOME] screen, the user bits setting screen appears.
	rr Time code settings screen:
	ffTo set the time code, press the <%/REW> button to change to the time code setting mode.
	ffThe setting values of each digit of the time code are from [0] to [9] (decimal).
		[TCG]	When the <%/REW> button is pressed, [SET] is
		Starts and exits the time code setting mode.	displayed in black and white inversion, and the time
	<%/REW> button	ffThe time code setting is applied when the setting	code setting mode is set.
		mode exits.	When the <%/REW> button is pressed again,
			[SET] returns to the normal display, and the time
			code setting mode exits.
		[TC_MD]	[F‑RUN]
		Selects the advance setting mode for the built-in	Use this function to advance the time code
		time code generator.	continuously, regardless of the P2 card recording
			operation. Set to this position to, for example, set
			the time code to the current time or externally lock
			the time code.
	<STOP> button		[R‑RUN]
			Use this function to advance the time code only
			during recording. A time code recorded normally will
			be continuously recorded.
			ffIf a clip is deleted, or if the frame rate is set to
			[24P]/[24PA] and the recording continues to
			a frame other than [24P]/[24PA], continuous
			recording may fail.
	<FF/)> button	[−]
		Decreases the setting value of the selected digit in the time code.
	<PLAY/PAUSE> button	[+]
		Increases the setting value of the selected digit in the time code.
	<COUNTER> button	[TC/UB]
		Switches to the user bits setting screen.
	<RESET> button	[RST]
		Resets all time code setting values to 0.
	<MONITOR SEL> button	[→]
		Moves the selected digit in the time code to the right. When the selected digit moves to the right edge, it
		moves back to the left edge.
	rr User bits settings screen:
	ffTo set the user bits, press the <%/REW> button to change to the user bits setting mode.
	ffThe setting values of each digit of the user bits are from [0] to [F] (hexadecimal).
		[UBG]	When the <%/REW> button is pressed, [SET] is
		Starts and exists the user bits setting mode.	displayed in black and white inversion, and the user
	<%/REW> button	ffThe user bits setting is applied when the setting	bits setting mode is set.
		mode exits.	When the <%/REW> button is pressed again,
			[SET] returns to the normal display, and the user
			bits setting mode exits.
		[TC_MD]
	<STOP> button	Switches to the advance setting mode for the built-in time code generator. The setting contents are the
		same as when [TCG] is selected.
	<FF/)> button	[−]
		Decreases the setting value of the selected digit in the user bits.
	<PLAY/PAUSE> button	[+]
		Increases the setting value of the selected digit in the user bits.
	<COUNTER>	[TC/UB]
		Switches to the user bits setting screen.
	<RESET> button	[RST]
		Resets all user bits setting values to 0.
	<MONITOR SEL> button	[→]
		Moves to the right of the selected digit in the user bits. When the selected digit moves to the right edge, it
		moves back to the left edge.
				indicates factory setting values.

– 143 –