Panasonic PT-D12000U, PT-DZ12000U How to use ADVANCED MENU

64 –

ENGLISH

How to use ADVANCED MENU

Digital cinema reality

Increase the vertical resolution when the PAL (or

SECAM) 576i signal input or the NTSC 480i, 1 080/50i

and 1 080/60i signal input is applied.

Press ▲▼ to select “DIGITAL 1.

CINEMA REALITY”.

ADVANCED MENU

DIGITAL CINEMA REALITY

BLANKING

AUTO

Press ◄► or ENTER.2.

The “DIGITAL CINEMA REALITY” individual •

adjustment screen will be displayed.

DIGITAL CINEMA REALITY

CHANGE

AUTO

Press ◄► to switch “DIGITAL 3.

CINEMA REALITY”.

The setting will change as follows each time •

◄► is pressed.

AUTO

30p FIXED: When 480i or 1 080/60i signals are input

25p FIXED: When 576i or 1 080/50i signals are input

OFF

AUTO:•

Performs automatic detection and cinema

processing. (factory default)

OFF: •

Unforced cinema processing

25p FIXED:•

Forced cinema processing (2:2 pulldown) is

performed when a 576i or 1 080/50i signal is input.

30p FIXED:•

Forced cinema processing (2:2 pulldown) is

performed when a 480i or 1 080/60i signal is input.

Note

In DIGITAL CINEMA REALITY mode, the image •

quality will be deteriorated if 30p FIXED or 25p

FIXED is selected when the signal is not a 2:2

pulldown signal.

Blanking adjustment

Blanking adjustment fine-tunes the images projected

by the video deck or other devices when the noise

appears on the edges of the screen or if a part of the

image lies slightly offscreen.

Press ▲▼ to select “BLANKING”.

1.

DIGITAL CINEMA REALITY

BLANKING

INPUT RESOLUTION

AUTO

Fine settings are possible.

MENU

Press to display the MAIN

MENU screen.

Press to select

“ADVANCED MENU”.

Press to display the

“ADVANCED MENU”

menu.

ENTER

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

PROJECTOR SETUP

P IN P

TEST PATTERN

SIGNAL LIST

SECURITY

NETWORK

MENU SELECT

SUB MENU

▲▼◄►

ENTER

MENU

Contents

Main Dear Panasonic Customer: Basic OperationSpecial FeaturesInformation Contents IMPORTANT SAFETY NOTICE Page Precautions with regard to safety WARNING a strange smell coming from the projector, turn off the power and take the full weight of the projector. is dropped or the cabinet is broken, turn off the power and disconnect Page Page Page Before Using Accessories Caution when moving the projector Cautions regarding setup Do not touch the surface of the projection lens with bare hand. DLP chips Lamp Maintenance Caution: Disposal Location and function of each part Front Remote control unit Side Top Bottom Location and function of each part (continued) Front Projector Main Unit Rear Controls Side Location and function of each part (continued) Connection terminals Using the remote control unit Loading batteries Open battery compartment lid.1. $ # Insert the batteries.2. Setting projector ID number to remote control Using a wired remote control Installation Examples of system expansion Adjusting the feet Projection scheme Installation geometry When attaching an optional ceiling mount bracket (ET-PKD100H) Projected range using geometric adjustment L2 R2 R3 L2 R2 L3 Screen L3 Projection distances by the type of projection lenses (optional) L : Projection distance SH : Effective screen height SW : Effective screen width Side View Top View Projection distances by the type of projection lenses (for PT-DZ12000U) For the screen aspect ratio of 16:9 (Units: m (feet/inches)) Lens type Zoom lens Fixed-focus Model number of Throw ratio*1 1.4-1.8 : 1 1.8-2.8 : 1 2.8-4.6 : 1 4.6-7.4 : 1 7.3-13.8 : 1 0.9-1.1 : 1 0.7 : 1 70 Projection distances by the type of projection lenses (for PT-D12000U) For the screen aspect ratio of 4:3 (Units: m (feet/inches)) Lens type Zoom lens Fixed-focus Model number of Throw ratio*1 1.5-2.0 : 1 2.0-3.0 : 1 3.0-5.0 : 1 5.0-8.0 : 1 7.9-15.0 : 1 1.0-1.2 : 1 0.8 : 1 (for PT-DZ12000U) Calculation formulas for projection distance by lens types (for PT-D12000U) Installation dimensions diagram Figure 1 : Dimensions applying when one unit is used Figure 2 : Dimensions applying when two units are used) Figure 3 : Maximum rotation allowable Connection Before starting connection The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below. The pin-out and signal names of the RGB2 IN terminal are shown in the diagram below. The pin-out and signal names of the DVI-D IN terminal are shown in the diagram below. Example of connecting with VIDEO devices Example of connecting with personal computers Installation of (optional) input modules Installing the input module Types of the input modules (optional) Procedure of installation Remove the slot cover.1. Insert the input module.2. Install the two screws.3. Register the input signal.4. Installation of (optional) input modules (continued) Connecting signals to the input module Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input module Installation of (optional) input modules (continued) Connecting the signal to the dual link HD/SD-SDI input module Connecting signals to the DVI-D input module How to install and remove the projection lens (optional) How to install the projection lens How to remove the projection lens Projection Power indicator lamp Connecting the power cord Powering up the projector Making adjustment and selection Powering off the projector How to adjust the lens How to adjust the focus, zoom and shift Adjustment range after lens position (optical shift) Zoom Lens ET-D75LE6 ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 The ET-D75LE5 has a fixed focal point, and so shift adjustment cannot be carried out. Relationship between lens orientation and screen focus Procedure for adjusting the focus balance (tilt compensation in the lens mount) Structure of lens mount (Figure 2, Figure 3) Adjustment procedure How to adjust the lens (continued) Precautions for projector installation work Registration of input signal data Registration of new data Renaming the registered signals Press to select the 1. signal whose details are to be displayed. Press ENTER.2. Clearing Registered Signals data 1. whose data is to be cleared. Press DEFAULT.2. Press ENTER.3. Sub memory memory Press on normal screen 1. (when the menu is not displayed). How to erase sub memory On-screen indications Basic operations using the remote control Using the SHUTTER Press SHUTTER on the remote 1. control or the main unit. Press SHUTTER again.2. On-screen display Automatic adjustment (AUTO SETUP) Press AUTO SETUP on the 1. remote control or the main unit. Turning on button illumination Press LIGHT on the remote 1. Using the FUNC1 button Changing the picture aspect ratio Press ASPECT on the remote 1. On-screen menus MAIN MENU SUB MENU PICTURE (pp. 54-59) On-screen menus (continued) POSITION (pp. 60-63) ADVANCED MENU (pp. 64-68) DISPLAY LANGUAGE (p. 69) DISPLAY OPTION (pp. 70-76) PROJECTOR SETUP (pp. 77-84) Using the menu screens Press MENU.1. Press to select the desired 2. item. Press ENTER to establish your 3. selection. Returning to the previous screen Adjusting the picture Switching the picture mode Press to select PICTURE 1. Press to switch PICTURE 2. Adjusting Contrast Adjusting Brightness Adjusts the brightness (black level) of the picture. Press to select 1. BRIGHTNESS. Press or ENTER.2. The BRIGHTNESS individual adjustment screen will be displayed. desired white balance Select USER1 or USER2 in 4. Step 3. Press ENTER.5. Press to select WHITE 6. BALANCE HIGH or WHITE BALANCE LOW. Press ENTER.7. Press to select RED, 8. GREEN or BLUE. Press to adjust the level.9. compensation amount adjustment) compensation amount Registering the picture mode settings as presettings Setting the system selector signal To display pictures complying with the sRGB standard Adjusting the position Shift adjustment Press to select SHIFT.1. Press ENTER.2. Press to adjust the 3. position. For horizontal (right and left) Adjusting the aspect ratio Press to select ASPECT.1. Press or ENTER.2. Press to switch ASPECT.3. Adjusting the position (continued) Adjusting the zoom ratio Press to select ZOOM.1. Press ENTER.2. Press to select MODE.3. Press to switch MODE.4. Press to select 5. INTERLOCKED. Select KEYSTONE or 3. CURVED in Step 2, and then press ENTER. Press to select the desired 4. adjustment item, and press to adjust the correction amount. How to use ADVANCED MENU Digital cinema reality Press to select BLANKING. Press to select DIGITAL 1. CINEMA REALITY. Press or ENTER.2. Adjusting the input resolution Press to select INPUT 1. RESOLUTION. Press ENTER.2. Adjusting the clamp position Press to select CLAMP 1. POSITION. marker Frame delay How to use ADVANCED MENU (continued) Press to switch FRAME 2. DELAY. Raster position Press to select RASTER 1. POSITION. Press ENTER.2. Press to adjust the 3. position. PT-D12000U PT-DZ12000U Setting the DISPLAY LANGUAGE Changing the display language Press to select the desired 1. language. Press ENTER to establish your 2. selection. Display Option settings Adjusting color matching Press to select COLOR 1. MATCHING. Press to switch COLOR 2. MATCHING. If 3COLORS or 7COLORS and chromaticity coordinates Large Screen Correction Screen setting RGB IN (Only RGB input) Press to switch AUTO 4. SIGNAL. AUTO SETUP DVI-D IN Press to select DVI-D IN.1. Press ENTER.2. Press to switch DVI EDID.3. Press to switch DVI 4. SIGNAL LEVEL. AUX DVI IN (Only when the ET-MD77DV is installed) Press to select AUX DVI IN. 1. Press ENTER.2. Press to switch AUX DVI 3. EDID. On-Screen display setting Press to select 1. ON-SCREEN DISPLAY. Press ENTER.2. Press to select the desired 3. item, and press to change the setting. OSD POSITION Setting the startup logo Press to select STARTUP 1. LOGO. Press to switch STARTUP 2. LOGO. Projector setup Setting a projector ID Press to select 1. PROJECTOR ID. Press to switch 2. PROJECTOR ID. Press MENU twice.3. Installation Setting Altitude Mode Direction Lamp select Press to select LAMP 1. SELECT. Press to switch LAMP 2. SELECT. Press ENTER.3. Projector setup (continued) Lamp relay Press to select LAMP 1. RELAY. Press to switch LAMP 2. RELAY. RS-232C setting Press to select RS-232C.1. Status Press to select STATUS.1. Press ENTER.2. Press to move to the next 3. page. Press to move to the next 4. page. Auto power off Press to select AUTO 1. POWER OFF. Press to switch AUTO 2. POWER OFF. Setting FUNC1 Setting the date and time Save all user data Load all user data Initialize Service password P IN P Using the P IN P function Press ENTER.1. Press to select P IN P 2. Press to select a function.3. P IN P (continued) Displaying the internal test pattern Test pattern Press to search through the 1. various types of test patterns. Cycle of displayed internal test patterns Setting the security Displaying the security screen If using for the first time Press , , , , , , and 1. in this order. If the existing password has been changed Changing the text Changing the security password Setting the text Control device setup How to use network functions Network standby Press to select NETWORK 1. STANDBY. Press to switch NETWORK 2. STANDBY. Initial setting of network Network control Press to select NETWORK 1. CONTROL. Press ENTER.2. Press to select items, and 3. press to change the setting. Network status Network connections Name and function of network function parts Accessing from the Web browser Basic control page Detail control page Projector status page Error information page OK: Normal operation FAILED: Occurrence of trouble When [FAILED] has appeared for an item Parameter Description E-mail setup page Page E-mail setup page (continued) Authentication set up page Ping test page Contents of mail sent Mail with the contents shown below is sent when the E-mail settings have been established. Mail with the contents shown below is sent when an error has occurred. Adjust clock page Network config page Firmware update page Using the PJLink protocol Supported commands PJLink security authorization Using the serial terminals Examples of connection For RS-232C Single projector Multiple projectors For RS-422 Single projector Multiple projectors Pin assignments and signal names Communication conditions (Factory setting) Basic format Control commands Cable specifications Connecting to a PC For RS-232C When multiple projectors are connected Using the Remote 2 terminal Example of a control panel layout Pin assignments and control Monitor Lamp Indicators LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) LAMP 1 monitor (LAMP 1) LAMP 3 monitor (LAMP 3) Temperature monitor (TEMP) Name of monitor lamp Cleaning and replacement of air filter Procedure of cleaning Page Replacement of lamp unit WARNING Precautions on lamp unit replacement Timing of lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement Notes when installing the ceiling mount bracket Installation procedure Before asking for service Symptoms Check point Page Self-diagnosis display Details Remedy Self-diagnosis display Details Remedy The self-diagnosis display and details of the failure may sometimes differ. Specifications Model No. PT-D12000U PT-DZ12000U or more (35 to 40 When the projector is used in high altitude mode (1 400 to 2 700 m), the ambient temperature is 0 . Furthermore, if the ambient temperature becomes 40 Appendix Compatible Signals *1: Only when using VESA CVT RB (Reduced Blanking) Appendix (continued) List of P IN P Subwindow Main window Dimensions Outside dimensions unit : mm (inch) Index A B C D R S T U W Information on Disposal in other Countries outside the European Union Note: Trademark Acknowledgement NOTES IMPORTANTES CONCERNANT LA SCURIT Prcautions de scurit AVERTISSEMENT vous remarquez que de la fume ou une odeur suspecte schappe du rsistant pour supporter le poids du projecteur. lintrieur du projecteur, de chute du projecteur ou de brisure du Page Page Page Avant lutilisation Accessoires Mise en garde concernant les dplacements du projecteur Mises en garde concernant la configuration install lobjectif de projection. Remarques concernant lutilisation Pour voir des images trop claires : Ne jamais toucher la surface de lobjectif de projection avec les mains nues. Puces DLP Lampe Remplacement de la lampe AVERTISSEMENT Prcautions prendre lors du remplacement de la lampe Intervalle de remplacement de la lampe Indication aprs 1 800 heures Procdure de remplacement de la lampe