Nn.n DDS | Paradyne 3616, 3615 specification

COMSPHERE DualFlow Data Service Units

	Table C-3
	(3 of 3)
	Device Health and Status Messages

Message	Condition

Redun Fan Alarm	Indicates a problem with the fan on the ±48 Vdc Central Office Power Unit.

Redun Pwr Alarm	Indicates a problem with the power on the ±48 Vdc Central Office Power Unit.

Subnetwrk Alarm	A major alarm was set Off by one of the devices in your subnetwork. Check the
	Subnetwork Health and Status report.

Subtree Truncat	Downstream health and status information has been truncated because it overflowed
	system limits.

OutofFrameThresh	For DBMs operating on a single port (rate adaption or nondisruptive), the local DBM
	has detected a continuous Out-of-Frame condition. The alarm clears when a local DBM
	synchronizes with a remote DBM.
	On a point-to-point circuit, if the alarm continues and the local DSU is configured for
	automatic backup, the local DSU disruptively tests the DDS circuit. If the test fails, the
	local DSU initiates a DDS Facility Alarm and initiates dial backup.

nn.n DDS	Indicates the speed (nn.n) of the DSU core when there are no alarms.

nnn Disable	Transmitter at nnn (DSU or DBM) is disabled. (Go to the Control branch to enable the
	DSU or DBM.)

nnn DTR Alarm	The DTR lead at nnn (DSU or DBM) has been Off for more than 30 seconds.

nnn StreamTerm	Streaming terminal. DTE at nnn (DSU or DBM) has its RTS lead turned ON longer than
	the predefined time.

C-6

December 1996

3615-A2-GB20-20

Image 97

Paradyne 3616, 3615 manual Nn.n DDS

Contents

Comsphere Dualflow Data Service Units Trademarks Warranty, Sales, and Service InformationCopyright 1996 Paradyne Corporation. All rights reserved Important Safety Instructions Government Requirements Interface Data Rate Code Bps DDS Table of Contents Glossary Index List of Figures Model 3616 DSU Installation and Circuit Pack Lock List of Tables Wire Switched 56 DBM Technical Specifications 1Model 3615 ± Digital DDS and 4-Wire Switched 56 kbps Preface How to Use This GuideAbout This Guide Reference Documents Related Documents About Your DualFlow DSU Standard FeaturesOverview DBMs DBM Features Switched 56 DBMs Technical Specifications Specifications Criteria General Technical Specifications Application DSU Technical Specifications Modulation and Frequency DBM Technical Specifications Criteria Wire Switched 56 DBM Technical Specifications Criteria Equipment Warranty and Support Before You Begin Installing the Model DualFlow DSU Procedure How to Change Hardware Straps Permissive V.32 DBM transmit output level of ±9 dBm Installing the DSU Where to Place the DSU Power-Up Routine Connecting to the Network Connecting to the Dial or Pstn Network Connecting to the NMS Connecting to the DDS or Lads Network Connecting to Switched 56 kbps Network Network Connection Wire Gauge AWG KbpsLads Connection Distances Data Rate Router Connection Connecting the DSU to a Router Addressing the Unit Verifying Operation and Testing ConnectionsTributary DSU Addressing Verifying Network Addresses Verifying DBM Operation Other Tests Verifying the Network Installing the Model 3616 3 DualFlow DSU Before You Begin Installing the Model 3616 DualFlow DSU Strap State Function Designation Jumper Strap Model 3616 DSU Jumper Straps Comsphere 3000 Series Carrier, Rear View Model 3616 DSU Installation and Circuit Pack Lock V.35 Interconnect Cable Installation Connecting to the Dial or Pstn or Switched 56 kbps Network Connecting to DDS or Lads Network Addressing the Unit CarrSlot 1 a To Connect the Sdcp to a DSU Verifying Network Addresses, the Network, and DBM Operation Assigning an Address Operating the DSU Model 3615 DCP DCP and Sdcp Operation Sdcp and Model 3616 DSU Faceplate Status Branch Menu StructureKeypad Top-Level Menu Device Health and Status Health and StatusExpanded Health and Status Subnetwork Health and Status Identity Circuit QualityIdentity Descriptions Description Information Displayed Terminal Power Backup BranchDial Backup Operation Configuring the Unit for Dial Backup Current Backup Effect Backup Mode Command Backup Branch Menu SelectionsUnderstanding Operating Modes Test Branch Manual BackupAbort Device Test DTE Loopback Local LoopbackDigital Loopback Remote Digital Loopback Digital Test Bilateral LoopbackEnd-to-End Test Bit Error Rate Test Results Information Displayed Bit Error Rate TestEnd-to-End Test Results Results Reported By Information Displayed Selecting an Application Configuration Configuration BranchLamp Test Poll List Configuration OptionsDisplaying the Poll List Changing the Poll List Acquiring the Poll List Directory Entry and Password Characters UseDirectory Undo Entering a Telephone Number Network Address PhoneAssigning an Address Control Branch Lead States SymbolLEDs Transmitter Control Displaying External Leads Message BranchChanging External Leads Reporting External Lead Changes to NMS Security Functions Available Access Level Security Access LevelsFront Panel DCP Security DualFlow DSU cannot configure a non-DualFlow DSU remotely Unit Configuration Editing Configuration Options Using the DCP to Set Configuration Options Example Using the DCP Saving Configuration Options Load from DiDg Activ Remot Understanding the Tables Configuration Option Tables DSU Configuration Options DSU Port Configuration Options Performs a Digital Loopback DTR Alarm Disab Next Enab Disab Prev DBM Configuration OptionsLL by DTE Disab Next Enab Disab Prev Bilat LpbkDisab Next Enab Disab Prev Yes CarrLossDisc Yes Next Yes No PrevAuto RetrainYes Next Yes No Prev Single Rate No Next Yes No Prev Alarm Call SetupNone Next None Pswrd Cllbk Alarm PrevNone Pswrd Remot DBM4-wire Next 2-wire 4-wire Prev EchoCancelDisab Next Enab Disab PrevWire Primary CoreNo Next Yes No Prev DBM Port Configuration Options DSR on Tst Enab Next Enab Disab Prev DSR FrcOn Enab Next Enab Disab PrevRespondRDL Disab Next Enab Disab Prev RL by DTE Disab Next Enab Disab Prev CCN by EL Disab Next Enab Disab Prev Stop Bits 1 for DiDg configurationNext Prev Will not be displayed Diag Type Disr Next NonD Disr None Prev Diagnostic DBM Configuration OptionsNonD Disr Trib Diagnostic General Configuration OptionsRemoteDiagEnhan Next V.54 Enhan Prev Backup Configuration Options RestorTimOut 5m Next Chang Prev TriesTimeOut15m Next Chang PrevMultiCallDisab Next Enab Disab Prev DBM 9.6 C Local Remot Msg DSU Menu a Comsphere DualFlow Data Service Units DSU Menu From Page A-1 Local/Remote Menu Subbranches Overview Instructions Configuration Worksheets B Date Location Local Phone No Device Local Addr Serial No DualFlow DSU Configuration Worksheet 1 DBM Port Value DualFlow DSU Configuration Worksheet 2 Overview Status Indicators Status Indicators and C Control Panel Messages Table C-1 DSU Status IndicatorsLabel Color Description Control Panel Messages Sdcp Status IndicatorsFormat Health and Status Messages Message Condition Device Health and Status MessagesTable C-3 Table C-3 Device Health and Status Messages Condition Nn.n DDS Expanded Health and Status Messages Table C-4 Subnetwork Health and Status Messages Table C-5 Dial Backup Progress Messages Command Progress MessagesProgress Messages Table C-7 Table C-8 Command Error Messages Condition Action Error Messages DBM DBM Pin Assignments D Network Connectors Hubbing Device Hubbing Device DC OUT DTE Connectors Ccitt Figure D-4. V.35 Interconnect Cable 3000-F1-510 Pin Number CablePlate Figure D-5. EIA-232-D Crossover Cable 4951-035F Crossover Cables Figure D-6. V.35 Crossover Cable 3211-178F Application Configurations E Dial Backup for Received Data Errors Application Dial Backup for Exceeded Load Thresholds Application Frame Relay Simultaneous Diagnostic Application = Field Install Equipment Feature/Part No Comcode = Factory InstallEquipment List F Comsphere 3000 Series Carrier, Installation Manual Equipment Part Number Model 3616 in U.S.A Glossary Auto backup DSR FEP RTS Series Network Index Index-2 Index DTR Index-5 Lads Index-7 Index-8 SDCP, C-3 Verifying