Configuring the Ethernet Port, Interface Status | Paradyne 9783

Configuration Options

Configuring the Ethernet Port

Select Ethernet Port from the Management and Communication menu to configure the Ethernet port (see Table 4-17).

Main Menu → Configuration → Management and Communication →

Ethernet Port

Table 4-17. Ethernet Port Options (1 of 2)

Interface Status

Possible Settings: Enable, Disable

Default Setting: Enable

Determines whether the Ethernet port is being used and can be configured.

Enable ± The port is active. It can receive Version 2 or IEEE 802.3 MAC frames, or transmit Version 2 MAC frames only.

Disable ± The port is not active. When the port is disabled, the following will occur:

HNo alarms or traps configured for the port will be generated.

HAll port uses that refer to the Ethernet port, like the Default IP Destination and Initial Route Destination, will be reset to their default values (see Table 4-11, Node IP Options, and Table 4-16, SNMP Trap Options).

IP Address

Possible Settings: 001.000.000.000 ± 223.255.255.255, Clear

Default Setting: Clear (000.000.000.000)

Specifies the IP address needed to access the Ethernet port.

001.000.000.000 ± 223.255.255.255 ± Shows the IP address for the port, which can be viewed or edited.

Clear ± Fills the IP address with zeros.

Subnet Mask

Possible Settings: 000.000.000.000 ± 255.255.255.255, Clear

Default Setting: 000.000.000.000

Specifies the subnet mask associated with the IP address that is needed to access the

Ethernet port.

000.000.000.000 ± 255.255.255.255 ± Set the Ethernet port's subnet mask. The range for each byte is 000 to 255.

Clear ± Fills the subnet mask associated with the IP address with zeros.

Default Gateway Address

Possible Settings: 001.000.000.000 ± 223.255.255.255, Clear

Default Setting: Clear (000.000.000.000)

Specifies the IP address for the port's default gateway. It is used for packets that do not have a route.

001.000.000.000 ± 223.255.255.255 ± Shows the IP address for the port, which can be viewed or edited (i.e., a router on the LAN).

Clear ± Fills the default gateway's IP address with zeros.

4-40

July 2000

9783-A2-GB20-00

Image 80

Paradyne 9783, FrameSaver DSL manual Configuring the Ethernet Port, Ethernet Port Options 1, Interface Status

Contents

FrameSaver DSL Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuration Options Operation and Maintenance Troubleshooting Setting Up Network Health for FrameSaver Devices Index Document Organization About This GuidePurpose and Intended Audience Troubleshooting. Provides device problem resolution Alarm, and other information, as well as troubleshootingTest procedures Setting Up OpenLane for FrameSaver Devices. Identifies Product-Related Documents When viewing this manual online. Click on Conventions UsedTo indicate a hyperlink to additional information Highlighted text System Overview About the FrameSaver DSL UnitSystem Overview FrameSaver DSL Features and Benefits Features 9783-A2-GB20-00 July Benefits DSL ATM Frame Relay FrameSaver DSL Feature Sets Feature Set Basic Advanced Feature Basic Features Maximum Number of PVCs and Management PVCs Supported Advanced SLV Features OpenLane SLM System About the FrameSaver DSL Unit User Interface Basic Operation Procedure Logging On If your login was Then Main Menu Select This is a remote-site unit that supports 8 PVCs and has Screen Work AreasScreen Format Description Press Navigating the ScreensKeyboard Keys Function Keys Select For the screen Press Enter to Function Switching Between Screen Areas Selecting from a Menu Example Selecting a FieldEntering Information User Interface and Basic Operation Configuration Procedures Basic Configuration Configuration Menu Configuration Option Areas Configuration Option Area Description Accessing and Displaying Configuration Options Main Menu → Configuration Changing Configuration Options Configuration → PVC Connections Saving Configuration Options Configuration Options Overview Configuration Options Easy Install Screen Example Using the Easy Install FeatureMain Menu → Easy Install TS Access VPI Easy Install Configuration Options 1TS Access Dlci Easy Install Configuration Options 2 TS Access VCICreate a Dedicated Network Management Link Ethernet Port Options Screen Setting Up So the Router Can Receive RIP Entering System Information Setting the System ClockConfiguration → Data Ports → Dlci Records Main Menu → Control → System Information Configuration Option Tables Configuring the Overall System Configuring Frame Relay and LMI for the System Main Menu → Configuration → System → Frame Relay and LMISystem Frame Relay and LMI Options 1 LMI Behavior System Frame Relay and LMI Options 2 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 Configuring Service Level Verification Options Service Level Verification Options 1 SLV Packet Size bytes Service Level Verification Options 2SLV Timeout Clearing Event Threshold Configuring General System Options Main Menu → Configuration → System→ GeneralTest Timeout General System Options Configuring the Physical Interfaces Configuring the Network InterfaceMain Menu → Configuration → Network → Physical Network Physical Interface Options Configuring the User Data Port Main Menu → Configuration → Data Ports → PhysicalData Port Physical Interface Options 1 Transmit Clock Source Port DTE Initiated Loopbacks Data Port Physical Interface Options 2Monitor DTR Configuring Frame Relay for the Data Port Main Menu → Configuration → Data Ports → Frame RelayData Port Frame Relay Options 1 LMI Parameters Data Port Frame Relay Options 2 Configuring ATM for the Network Interface Main Menu → Configuration → Network → ATMCell Delineation Error Event Threshold Network ATM Options Configuring Circuit and Dlci Records Dlci Record Options 1Dlci Number VPI,VCI Number VPI Dlci Type Possible Settings Standard, Multiplexed Dlci Record Options 2CIR bps Committed Burst Size Bc Bits Dlci Record Options 3 Excess Burst Size BitsDlci Priority Outbound Management Priority 10. PVC Connection Options 1 Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 10. PVC Connection Options 2 Destination LinkDestination Dlci Destination Edlci Setting Up Management and Communication Options Configuring Node IP Information 11. Node IP Options 1 11. Node IP Options 2 TS Access Management Link 11. Node IP Options 3 Name Configuring Management PVCs12. Management PVC Options 1 Set DE Primary Link Possible Settings Net1-FR1, Port-1, Clear12. Management PVC Options 2 Primary Edlci 12. Management PVC Options 3Primary Dlci Configuring General Snmp Management Name 1 Access13. General Snmp Management Options 1 Snmp Management Name 2 Access 13. General Snmp Management Options 2 Configuring Telnet and/or FTP Session Support Telnet Login Required14. Telnet and FTP Session Options 1 Telnet Session Disconnect Time Minutes Inactivity Timeout14. Telnet and FTP Session Options 2 FTP Login Required 14. Telnet and FTP Session Options 3FTP Session FTP Max Transfer Rate Kbps Configuring Snmp NMS Security Access Type15. Snmp NMS Security Options NMS IP Validation Configuring Snmp Traps 16. Snmp Traps Options 1Snmp Traps Number of Trap Managers 16. Snmp Traps Options 2 Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both 16. Snmp Traps Options 3Link Traps Interfaces Rmon Traps Interface Status Configuring the Ethernet Port17. Ethernet Port Options 1 17. Ethernet Port Options 2 Proxy ARP Configuring the Communication Port 18. Communication Port Options 1Port Use Character Length Login Required 18. Communication Port Options 2Stop Bits Ignore Control Leads 18. Communication Port Options 3 18. Communication Port Options 4 RIP Configuring the COM Port to Support an External Modem External Modem CommandsDial-In Access 19. External Modem COM Port Options Security and Logins Limiting Access Controlling Asynchronous Terminal Access Set the configuration option Controlling External COM Port Device Access Controlling Telnet or FTP Access Limiting Telnet Access Limiting FTP Access Limiting Telnet or FTP Access Over the TS Management Link Controlling Snmp Access Disabling Snmp Access Assigning Snmp Community Names and Access Levels Limiting Snmp Access Through IP Addresses Field Enter Creating a LoginMain Menu → Control → Administer Logins Modifying a Login Deleting a Login Operation and Maintenance View this field To find Displaying System InformationMain Menu → Status → Identity Display LEDs & Control Leads Screen Viewing LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads LED Descriptions General Status LEDs 1 Label Indication Color What It Means Network Interface LEDs Label Indication Color What It Means User Data Port LED Label Indication Color What It Means Control Lead Descriptions Additional Control Leads Label Indication What It MeansNetwork Interface User Data Port Device Messages Device Messages 1 What It Indicates What To Do Device Messages 2 What It Indicates What To Do See Changing Software Device Messages 3 What It Indicates What To Do Device Messages 4 What It Indicates What To Do See Upgrading System Reset COM Port Device Messages 5 What It Indicates What To Do Status Information Status Menu Last System Reset Date and Time Self-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Self-Test Results Messages Health and Status Messages Health and Status Messages 1 What It Indicates Health and Status Messages 2 What It Indicates Frame relay link Health and Status Messages 3 What It Indicates Frame relay link 1, 2 Test Status Messages Test Status Messages 1 What It Indicates Test Status Messages 2 What It Indicates Send Pttn Active, Interface PVC Connection Status Main Menu → Status → PVC Connection StatusPVC Connection Status Screen Example PVC Connection Status 1 Field PVC Connection Status 2 Field What It Indicates Network Interface Status Main Menu → Status → Network Interface StatusNetwork Interface Status Screen Example 10. Network Interface Status Field What It Indicates IP Routing Table Screen Example IP Routing TableMain Menu → Status → IP Routing Table 11. IP Routing Table Values Column What It Indicates Performance Statistics Menu Performance StatisticsMain Menu → Status → Performance Statistics Clearing Performance Statistics Performance Statistics → Clear All StatisticsPerformance Statistics → Frame Relay Performance Statistics → ESF Line Service Level Verification Performance Statistics Average round trip latency is measured every SLV sampling 13. Dlci Performance Statistics 1 What It Indicates Dlci Performance StatisticsMain Menu → Status → Performance Statistics → Dlci 13. Dlci Performance Statistics 2 What It Indicates CIR&EIR Frame Relay Errors Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics → Frame Relay 14. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors contd Frame Relay Hdlc Errors14. Frame Relay Performance Statistics 2 What It Indicates Frame Relay LMI ATM Performance Statistics Main Menu → Status → Performance Statistics → ATM15. ATM Performance Statistics 1 What It Indicates TC Sublayer 15. ATM Performance Statistics 2 What It Indicates Statistic What It Indicates Ethernet Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Trap Event Log Screen Example Trap Event LogMain Menu → Status → Trap Event Log Operation and Maintenance FTP Operation FTP File Transfers Command Definition Dir directory Upgrading System Software If the message displayed is Then Determining Whether a Download Is Completed Changing Software Transferring Collected Data If retrieving Then Troubleshooting Problem Indicators Indicators See Resetting the Unit By Cycling the Power Resetting the Unit and Restoring CommunicationResetting the Unit from the Control Menu Restoring Communication with an Improperly Configured Unit If selecting Following occurs Main Menu → Control → LMI Packet Capture Utility Troubleshooting Management Link FeatureLMI Packet Capture Utility Feature LMI Packet Capture Utility → Display LMI Trace Log LMI Trace Log Example Alarms Alarm Conditions 1 What It Indicates What To Do Alarm Conditions 2 What It Indicates What To Do Alarm Conditions 3 What It Indicates What To Do Alarm Conditions 4 What It Indicates What To Do Troubleshooting Tables Device ProblemsSee Trap Event Log in , Operation and Maintenance Device Problems 1 Symptom Possible Cause Solutions Device Problems 2 Symptom Possible Cause Solutions Unit ATM Problems ATM Problems Symptom Possible Cause Solutions Frame Relay PVC Problems Frame Relay PVC Problems Symptom Possible Cause Solutions Tests Available Test Menu Example Starting and Stopping a Test Test Timeout FeatureWhen the status of a test is Only command available is Aborting All Tests Active PVC Tests PVC Tests Screen Example PVC Loopback Send PatternMain Menu → Test → Network PVC Tests Main Menu → Test → Data Port PVC Tests Monitor Pattern Connectivity DTE Loopback Main Menu → Test → Data Port Physical Tests IP Ping Test Main Menu → Test → IP Ping Procedure Lamp Test Main Menu → Test → Lamp Test OpenLane Support of FrameSaver Devices Setting Up OpenLane for FrameSaver DevicesOpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver and SLV Support Setting Up OpenLane for FrameSaver Devices Setting Up Network Health for FrameSaver Devices 10-1 Installation and Setup of Network Health Discovering FrameSaver Elements Configuring the Discovered Elements Grouping Elements for Reports About At-a-Glance Reports About Service Level ReportsGenerating Reports for a Group Printed Reports Reports Applicable to FrameSaver SLV DevicesAbout Trend Reports 10-8 10-9 10-10 Menu Hierarchy Menus Menu Hierarchy Frame Relay Mode Status Easy Install Control Menu Hierarchy Snmp MIBs and Traps, Rmon Alarm Defaults MIB Support Downloading MIBs and Snmp Traps FrameSaver Units sysObjectID system System Group mib-2FrameSaver Units sysDescr system Interfaces Group mib-2 Paradyne Indexes to the Interface Table ifTablePhysical Layer Frame Relay Logical Layer NetScout Indexes to the Interface Table ifTable Rmon Logical Layer Standards Compliance for Snmp Traps Examples Trap authenticationFailure Trap warmStartTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown Physical Sublayer Sample strings Table B-6. linkUp and linkDown Variable-Bindings 2 Interface Variable-Bindings Possible Cause ATM Logical Link Sublayer Traps enterprise-Specific DevHealthAndStatus SLVs devFrExt.mib Placeholder Traps RMON-Specific Rmon Alarm and Event Defaults Event DefaultsEventIndex EventDescription EventType Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults ± Paradyne Area MIB FR DTE MIB Frames Sent Snmp MIBs and Traps, and Rmon Alarm Defaults Object ID Cross-References Numeric Order 6.1.4.1.1795.2.24.2 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.4.1.1795.2.24.2.6.9.4 Dlci CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 Snmp MIBs and Traps, and Rmon Alarm Defaults Connectors, Cables, Pin Assignments Rear Panel Figure C-1. DSL Network Interface Cable with RJ48C Connector DSL Network Interface Cable COM Port Connector Signal Direction Pin # Standard EIA-232-D Crossover Cable Pin AT Command String To configure the modem to Direction Pin Socket Data Port ConnectorStandard V.35 Straight-through Cable Ethernet Port Connector Connectors, Cables, and Pin Assignments Technical Specifications COM Port DSL Network InterfaceEthernet Port Data Port Model / Feature Number FrameSaver SLV UpgradeEquipment List Equipment Description Model / Feature Number Description Part Number Feature NumberOptional Features Cables Index Numbers IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8 IN-9