Trunk Settings Programming Reference | Philips DBS-EX23-530 guide

Trunk Settings

Programming Reference

Parameter

ISDN DID Flexible Ringing Assignments

Description

This parameter enables or disables ringing for specific ISDN

Inbound DID numbers during Day, Night, Delayed Day and

Delayed Night modes.

Programming

FF1 9# 5# (0000-9999)# (100-699)# (000000-111111)#

Options

0=Disable ringing

1=Enable ringing

Where the entry position determines the ringing as follows:

The default entry is 111000 (day and night ringing enabled, delayed day and delayed night ringing disabled.

4-32

DBS-EX23-530

Revised April 2000

Image 84

Philips DBS-EX23-530 manual Trunk Settings Programming Reference

Contents

Isdn For CPC-EX VersionPage Contents Programming Reference DBS-EX23-530 Revised List of Figures List of Tables About This Manual OverviewRelated Documents Chapter Title Purpose Viii DBS-EX23-530 Revised April Introduction to the Isdn Interface Topic DBS-EX23-530 Revised April Overview Description of the Isdn InterfaceFraming Options Introduction to the Isdn Interface Overview Pre-Installation Requirements Ordering IsdnInformation Needed from CO Comments / Examples Typical Information for CO Comments Examples Lpic Information Needed from CO Site Information Typical Information for CO Site Information Span Item Master Cabinet Span Slave Cabinet Span ESF What You Must Purchase DBS Equipment CSU Equipment Page Installation DBS-EX22-530 Revised April Installation Guidelines GuidelinesHardware Requirements Maximums Guidelines Installation Trunk Assignments for Single-Cabinet Systems Trunk Assignments for Double-Cabinet Systems System Size Master Slave Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Installation Procedures Installing the CSUInstallation Procedures If you’re installing Use this procedure Installation Installation Procedures Parameter System Configuration Installing an Isdn in a Single Cabinet Attach the Sync Unit to the CPC-EX card Sync Unit installation MDF card installation Distance from the DBS to the CSU To 150 ft 150-450 ft 450-655 ft Pins Designation RJ48 Pin Designations Isdn cabinet connections, single-cabinet installation Installation Installation Procedures Installation Procedures Installation Installation Procedures Slave Cabinet Quick-Start Programming DBS-EX23-530 Revised April Before You Begin Quick-Start Programming Before You Begin DBS-EX22-530 Issued 10/23/98 Programming Initial Isdn OptionsMinimum Programming Programming Initial Isdn Options Quick-Start Programming Quick-Start Programming Programming Initial Isdn Options =Free run internal clocking Disable PublicNone = Loop start Send as is Determine Type and Plan FF1 9# 4# 5# 5# 3# 0-2# NSF Multiple did Programming =DID data on display=Off Typical Central Office Configurations CO Type 0 4ESS Programming Reference DBS-EX23-530 Revised April Isdn System Settings Programming Reference Isdn System SettingsSystem Size =T1 Clock Settings Isdn System SettingsProgramming Reference =None Isdn System Settings Programming Reference System-Wide Timers Programming Reference System-Wide Timers System-Wide Timers Programming Reference 15=Infinite=4 sec =30 sec System-Wide Timers Programming Reference Programming Reference System-Wide Timers Digital Pad Settings Digital Pad Settings Programming Reference Programming Reference Digital Pad Settings SLT Isdn #2 Extension Port Settings Digital Pad SettingsProgramming Reference Trunk Port Settings Programming ReferenceDigital Pad Settings Master and Slave Settings Trunk ConfigurationTrunk Signaling Master and Slave Settings Programming Reference Alarm Settings Alarm DescriptionsProgramming Reference Alarm Settings Alarm Description Notification Alarm Settings Programming Reference Parameter Address Function Slip Alarms Alarm Transmission Options =Yes Alarm Timers Programming ReferenceAlarm Settings=10 ms Error Counters for FF Alarm Keys Programming Reference Alarm Settings Alarm Settings Programming Reference Alarm Relay Controls =Off Alarm relay does not close Alarm Settings Programming Reference =Auto Trunk Settings Trunk Settings Programming Reference=Do not reset Programming Reference Trunk Settings Public network Disable None Send as is with Send as is with leading Trunk Settings Programming Reference =Off Extension Settings Extension Settings Programming Reference FF Key Settings Programming Reference FF Key SettingsAlarm Master Isdn Slave Isdn Special Isdn Function Codes Special Isdn Function Codes Programming Reference Programming Reference Special Isdn Function Codes Yellow Appendix a CPC-EX 2.3 Updates New Features Software Corrections Port Voice Mail Support via API Programming Off-Hook Voice Announce Ohva via API Small LCD Soft Key Support via API Call Record Ohva via API Special Features UNA Transfer Setting Value UNA Call Reversion Forwarding to UNA for CO Held Call DBS-2.3-400 DBS Manual Revised April A-9 All Ring Group Private Password FF1 6# 3# NNNN# Terminal Programming Through a Direct Connection ON/OFF #93 Terminal Programming Through Disa Additional RAI Access Method Terminal Programming Through Additional RAI Access MethodTerminal Programming Commands Command Description DBS-2.3-400 DBS Manual Revised April A-15 Isdn Upgrade Procedure Isdn Programming FlexibilityName Key Sequence Master Cabinet Set-Up DMS100 Send as isDetermine Type and Plan Slave Cabinet Set-Up DMS-100 Typical Central Office Configurations Lucent AT&T 4ESS Lucent AT&T 5ESS Nortel NT DMS100 Info Needed from CO Comments examplesTypical Info for CO Comments examples Will exceed the total number of B channels DBS-2.3-400 DBS Manual Revised April A-23 Feature Changes Affected Items FF1 2# 2# 7# System Speed Bins 257- 500 Unavailable Index Revised April DBS-EX23-530 Index-i Sync cable 2-18, 2-21, 2-23 Sync loss alarm Index-ii DBS-EX23-530 Revised April