Phonetics 1104 Appendix C: Accessories

Appendix C: Accessories

The sensors listed below are available from Sensaphone, Inc., and

represent the most commonly used input devices. Other dry

contact sensors, designed for more specialized applications, may

also be used. Commercial or industrial electrical supply houses

can provide devices to monitor virtually any condition. For

further information, contact Sensaphone Customer Service at

(610) 558-2700.

PART NUMBER SENSOR / SWITCH

FGD-0006 Magnetic Reed Switch

FGD-0007 Passive Infra-Red Detector

FGD-0010 Accessory Hook-Up Wire

FGD-0013 Water Detection Sensor

FGD-0022 Temp°Alert

FGD-0023 ISOTEL Surge Protector

FGD-0027 Humidistat

FGD-0049 Smoke Detector with Built-in Relay

FGD-0100 Remote Temperature Sensor

FGD-0101 Weatherproof Temperature Probe

FGD-0200 Phonecell SX3e Cellular Phone

105

Contents

Main Page IMPORTANT SAFETY INSTRUCTIONS CAUTION FCC Requirements Page Canadian Department of Communications Statement Page Chapter 2: Installation . . . . . . . . . . . . . . . . .15 Chapter 3: Quick Start . . . . . . . . . . . . . . . .25 Chapter 4: Communications Programming 33 Chapter 5: Alarm Programming . . . . . . . . .63 Page Chapter 1: Introduction Technical Support Chapter 2: Installation 2.1 Operating Environment 2.2 Mounting 2.3 Power Surge Protection 2.4 Power Supply and Battery Backup --- --- +++ +++ 2.5 Starting the Model 1104 2.6 Run Mode and Standby Mode RUN STANDBY 2.7 Telephone Line 2.8 The Microphone 2.9 Alert Inputs 2.10 Installing the Sensor 2.11 Multiple Sensors 2.12 Outdoor Wiring 2.13 Disconnecting the Model 1104 for Storage or Seasonal Use. Page Chapter 3: Quick Start 3.1 The Local Keypad 3.2 Preparation for Programming 3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs RUN Step 2: Set the ID Number STATUS Step 3: Set Dial-Out Telephone Numbers PHONE NUMBER Step 4: Set Temperature Limits Page Page 3.4 Summary of the Alarm Dial-Out Process ActionResponse Programmable Feature Chapter 4: Communications Programming 4.1 The Unit ID Number 4.1.1 Programming the ID Number 4.1.2 Interrogating the ID Number 4.2 Dial-out Telephone Numbers 4.2.1 Programming Dial-out Telephone Numbers 4.2.2 Interrogating a Dial-out Telephone Number 4.2.3 Erasing a Telephone Number Page 4.3 Tone or Pulse Dialing 4.4 Special Dialing 4.4.1 Special Dialing Keys 4.4.2 Incorporating a Pause 4.4.3 Incorporating a Pound (#) or Asterisk (*) Page 4.4.4 Special Dialing to a Beeper or Pager Page 4.5 Rings Until Answer 4.5.1 Programming Rings Until Answer 4.5.2 Interrogating Rings Until Answer 4.6 TAD (Telephone Answering Device) 4.6.1 TAD Enable/Disable 4.6.2 Using the TAD Feature 4.6.3 No TAD In Use 4.7 Listen-in Time 4.7.1 Programming the Listen-in Time 4.7.2 Interrogating the Listen-in Time 4.8 Call Delay 4.8.1 Programming the Call Delay 4.8.2 Interrogating Call Delay 4.9 Local Voice Mute 4.9.1 Enable/Disable Local Voice Mute 4.10 Voice Repetitions 4.10.1 Programming Voice Repetitions 4.10.2 Interrogating Voice Repetitions Page 4.11 Intercall Time 4.11.1 Programming Intercall Time 4.11.2 Interrogating Intercall Time 4.12 Maximum Number of Calls (Max Calls) 4.12.1 Programming Max Calls 4. Press ENTER. The Model 1104 responds:Enter. 4.12.2 Interrogating Max Calls 4 WHAT IS * Chapter 4: Communications Programming 4.13 The Clock 4.13.1 Setting the Clock 4.13.2 Interrogating for the Current Time 4.14 The Security Code 4.14.1 Locking the Keypad 4.14.2 Unlocking the Keypad 3. Using the number keys, enter the digits for the code. Chapter 4: Communications Programming Page Chapter 5: Alarm Programming 5.1 Input Configuration 5.1.1 Programming Input Configuration 5.1.2 Verifying Input Configuration 5.2 Enable/Disable Inputs 5.2.1 Changing Enabled/Disabled Input Status 5.2.2 Verifying Enabled/Disabled Input Status 5.3 Input Recognition Time 5.3.1 Programming Input Recognition Time 7. Press ENTER. The Model 1104 responds:Enter. 5.3.2 Interrogating Input Recognition Time 1. Press WHAT IS. 2. Press RECOGNITION TIME. 7 WHAT IS * Chapter 5:Alarm Programming Page 5.4 Establishing High and Low Temperature Limits 5.4.1 Programming Temperature Limits for a Selected Input 5.4.2 Disabling Alarm Response to High or Low Temperature 5.4.3 Interrogating High and Low Temperature Limits 5.5 Temperature Scale 5.6 Temperature Calibration 5.6.1 Programming Temperature Calibration 5.6.2 Interrogating Temperature Calibration 5.7 Obtaining Current Temperature 5.8 AC Power Monitoring Enable/Disable 5.8.1 Enabling/Disabling the AC Power Alarm 5.9 AC Power Failure Recognition Time 5.9.1 Programming Power Failure Recognition Time 7. Press ENTER. The Model 1104 responds: OK. 0 7 SET # 5.9.2 Interrogating Power Failure Recognition Time 5.10 Sound Alarm Monitoring 5.10.1 Programming Sound Alarm Sensitivity 5.10.2 Interrogating Sound Sensitivity 5.10.3 Programming High Sound Alarm Recognition Time 5.11 High Sound Alarm Enable/Disable 5.11.1 Changing Enabled/Disabled High Sound Alarm 5.12 Exit Delay Chapter 6: Acknowledgment, Status Report & Remote Access 6.1 Alarm Acknowledgment 6.1.1 Local Acknowledgment 6.1.2 Touch-Tone Acknowledgment 6.1.3 Callback Acknowledgment 6.2 Status Report 6.2.1 Example: Status Report, No Alarms 6.2.2 Example: Status Report, Existing Alarms 6.2.3 Example: Status Report,Disabled Inputs 6.2.4 Battery Condition 6.2.5 Remote Access by Touch-ToneTelephone Page Page Chapter 7: Operation 7.1 Alarm Detection, Dial-out and Acknowledgment Page Page Page Page 7.2 Example: A Dial-out Telephone Call Appendix A: Troubleshooting Page Page Communications / Dial-out: Temperature Monitoring: Sound Level Monitoring: Page Other Monitoring: Appendix B: Weekly Testing Procedure Page Appendix C: Accessories Page Appendix D: Returning the Unit for Repair SERVICE DEPARTMENT Sensaphone, Inc. 901 Tryens Road Aston, PA 19014 1 YEAR LIMITED WARRANTY