Phonetics 1104

Every effort has been made to ensure that the information in this

document is complete, accurate and up-to-date. SENSAPHONE,

INC. assumes no responsibility for the results of errors beyond its

control. SENSAPHONE, INC. also cannot guarantee that changes

in equipment made by other manufacturers, and referred to in this

manual, will not affect the applicability of the information in this

manual.

Revised Edition, version 1.11, December, 2002

Written and produced by SENSAPHONE INC. Please address all

comments on this publication to:

SENSAPHONE, INC.

901 Tryens Road

Aston, PA 19014

www.sensaphone.com

Sensaphone®is a registered trademark of Phonetics, Inc.

Touch-Tone™ is a registered trademark of AT&T.

Sensaphone®Model 1104 User’s Manual

Contents

Main Page IMPORTANT SAFETY INSTRUCTIONS CAUTION FCC Requirements Page Canadian Department of Communications Statement Page Chapter 2: Installation . . . . . . . . . . . . . . . . .15 Chapter 3: Quick Start . . . . . . . . . . . . . . . .25 Chapter 4: Communications Programming 33 Chapter 5: Alarm Programming . . . . . . . . .63 Page Chapter 1: Introduction Technical Support Chapter 2: Installation 2.1 Operating Environment 2.2 Mounting 2.3 Power Surge Protection 2.4 Power Supply and Battery Backup --- --- +++ +++ 2.5 Starting the Model 1104 2.6 Run Mode and Standby Mode RUN STANDBY 2.7 Telephone Line 2.8 The Microphone 2.9 Alert Inputs 2.10 Installing the Sensor 2.11 Multiple Sensors 2.12 Outdoor Wiring 2.13 Disconnecting the Model 1104 for Storage or Seasonal Use. Page Chapter 3: Quick Start 3.1 The Local Keypad 3.2 Preparation for Programming 3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs RUN Step 2: Set the ID Number STATUS Step 3: Set Dial-Out Telephone Numbers PHONE NUMBER Step 4: Set Temperature Limits Page Page 3.4 Summary of the Alarm Dial-Out Process ActionResponse Programmable Feature Chapter 4: Communications Programming 4.1 The Unit ID Number 4.1.1 Programming the ID Number 4.1.2 Interrogating the ID Number 4.2 Dial-out Telephone Numbers 4.2.1 Programming Dial-out Telephone Numbers 4.2.2 Interrogating a Dial-out Telephone Number 4.2.3 Erasing a Telephone Number Page 4.3 Tone or Pulse Dialing 4.4 Special Dialing 4.4.1 Special Dialing Keys 4.4.2 Incorporating a Pause 4.4.3 Incorporating a Pound (#) or Asterisk (*) Page 4.4.4 Special Dialing to a Beeper or Pager Page 4.5 Rings Until Answer 4.5.1 Programming Rings Until Answer 4.5.2 Interrogating Rings Until Answer 4.6 TAD (Telephone Answering Device) 4.6.1 TAD Enable/Disable 4.6.2 Using the TAD Feature 4.6.3 No TAD In Use 4.7 Listen-in Time 4.7.1 Programming the Listen-in Time 4.7.2 Interrogating the Listen-in Time 4.8 Call Delay 4.8.1 Programming the Call Delay 4.8.2 Interrogating Call Delay 4.9 Local Voice Mute 4.9.1 Enable/Disable Local Voice Mute 4.10 Voice Repetitions 4.10.1 Programming Voice Repetitions 4.10.2 Interrogating Voice Repetitions Page 4.11 Intercall Time 4.11.1 Programming Intercall Time 4.11.2 Interrogating Intercall Time 4.12 Maximum Number of Calls (Max Calls) 4.12.1 Programming Max Calls 4. Press ENTER. The Model 1104 responds:Enter. 4.12.2 Interrogating Max Calls 4 WHAT IS * Chapter 4: Communications Programming 4.13 The Clock 4.13.1 Setting the Clock 4.13.2 Interrogating for the Current Time 4.14 The Security Code 4.14.1 Locking the Keypad 4.14.2 Unlocking the Keypad 3. Using the number keys, enter the digits for the code. Chapter 4: Communications Programming Page Chapter 5: Alarm Programming 5.1 Input Configuration 5.1.1 Programming Input Configuration 5.1.2 Verifying Input Configuration 5.2 Enable/Disable Inputs 5.2.1 Changing Enabled/Disabled Input Status 5.2.2 Verifying Enabled/Disabled Input Status 5.3 Input Recognition Time 5.3.1 Programming Input Recognition Time 7. Press ENTER. The Model 1104 responds:Enter. 5.3.2 Interrogating Input Recognition Time 1. Press WHAT IS. 2. Press RECOGNITION TIME. 7 WHAT IS * Chapter 5:Alarm Programming Page 5.4 Establishing High and Low Temperature Limits 5.4.1 Programming Temperature Limits for a Selected Input 5.4.2 Disabling Alarm Response to High or Low Temperature 5.4.3 Interrogating High and Low Temperature Limits 5.5 Temperature Scale 5.6 Temperature Calibration 5.6.1 Programming Temperature Calibration 5.6.2 Interrogating Temperature Calibration 5.7 Obtaining Current Temperature 5.8 AC Power Monitoring Enable/Disable 5.8.1 Enabling/Disabling the AC Power Alarm 5.9 AC Power Failure Recognition Time 5.9.1 Programming Power Failure Recognition Time 7. Press ENTER. The Model 1104 responds: OK. 0 7 SET # 5.9.2 Interrogating Power Failure Recognition Time 5.10 Sound Alarm Monitoring 5.10.1 Programming Sound Alarm Sensitivity 5.10.2 Interrogating Sound Sensitivity 5.10.3 Programming High Sound Alarm Recognition Time 5.11 High Sound Alarm Enable/Disable 5.11.1 Changing Enabled/Disabled High Sound Alarm 5.12 Exit Delay Chapter 6: Acknowledgment, Status Report & Remote Access 6.1 Alarm Acknowledgment 6.1.1 Local Acknowledgment 6.1.2 Touch-Tone Acknowledgment 6.1.3 Callback Acknowledgment 6.2 Status Report 6.2.1 Example: Status Report, No Alarms 6.2.2 Example: Status Report, Existing Alarms 6.2.3 Example: Status Report,Disabled Inputs 6.2.4 Battery Condition 6.2.5 Remote Access by Touch-ToneTelephone Page Page Chapter 7: Operation 7.1 Alarm Detection, Dial-out and Acknowledgment Page Page Page Page 7.2 Example: A Dial-out Telephone Call Appendix A: Troubleshooting Page Page Communications / Dial-out: Temperature Monitoring: Sound Level Monitoring: Page Other Monitoring: Appendix B: Weekly Testing Procedure Page Appendix C: Accessories Page Appendix D: Returning the Unit for Repair SERVICE DEPARTMENT Sensaphone, Inc. 901 Tryens Road Aston, PA 19014 1 YEAR LIMITED WARRANTY