Initializing Setup Module | Printek 4000se manual

U S I N G T H E O P T I O N A L S E T U P M O D U L E

When the message disappears, installation is complete and the printer will continue with its normal power up procedure.

Initializing

Setup Module

7.The printer will now compare the configuration data in its internal memory to the data in the Setup Module. If the data is not an exact match, proceed with step 8.

If the data in the printer and the data in the module are an exact match, installation is complete and the printer will complete its power up procedure.

8.The printer has now determined that the data in the Setup Module does not exactly match the data in the printer’s internal memory. The printer will now display the following message and the bell will beep to get the operator’s attention. Proceed to step 9.

New Setup

Module

Detected

9.Press the ONLINE button. The printer will display the following message. You must now make one of the selections as described below.

Load = Read

Unload = Write

If you wish to copy the Setup data to the printer from the Setup Module, press the LOAD button. The printer will display the following message and will now be configured according to the information that was in the Setup Module.

Copying Setup to Printer

92

Image 100

Printek 4000se Initializing Setup Module, New Setup Module Detected, Load = Read Unload = Write, Copying Setup to Printer

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Common Error Conditions Introduction To SetupError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting a Form Already Loaded In the Tractors Selecting And Loading FormsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Print ⎯0.30→ 12345 Check Paper Common Error ConditionsNo Paper to Load Too Much Paper to Unload Selected Form is not LoadedNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Introduction To Setup Printer ConfigurationSetup Buttons Entering Setup Entering Setup MenusUsing the Setup Button Using the Function and Value Buttons Exit Setup Yes Exiting SetupExiting Menus Saving Changes No Changes Forms Menu Items Forms MenuForm Name Form Tractor Path Front Automatic Cut No Cut Adjustment Lines/InchForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Bottom Margin 0 Lines Characters/Inc hLeft Margin Column Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Unidirectional No Entering the Interface Menu Interface MenuInterface I/o Serial Emulation EpsonAuto CR On Auto LF Off Characters Control Minimum Buffer NoBaud Rate Data Bits DTR Power On/Off Stop BitsParity None Busy Polarity Low XON/XOFF Off ETX/ACK Off Parallel/LAN Interface Items LAN Setup OffInterface Menu Parallel/LAN IP Address Auto IP AddressSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off User Language English Top Oversized OffSize 8192 Characters Truncate Lines No Ribbon Check On Ribbon Life Million Chars ImagerPlus Graphic CardImagerPlus Emulation QMS CodeV ControlCharact 5E Hex Line TerminatorBar Code Density High-Res QMS Char Set PY Translation Not Active Free Format Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical DPI Vertical Text VersionCodeV SP Fields Process IGP Char Set Delete Logos No Quiet Mode Not ActiveSpacing IGP 10/20/40 Test Menu Test Mode OffPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Setup Module Installation Using the Optional Setup ModuleIntroduction Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Specifications Print SpeedsCharacter Matrix Graphics Density Character Sets Character SpacingLine Spacing Line Length Special Forms Handling Features RibbonComputer Interface 113 Operator Controls/Indicators WarrantyReliability 114 Options Environmental Specifications115 Page Glossary of Terms 117 Ebcdic 118 119