Stop Bits, Parity None, Busy Polarity Low | Printek 4000se manual

P R I N T E R C O N F I G U R A T I O N

Stop Bits

Possible Values: 1*, 2

Stop Bits 1

This item sets the number of stop bits to be used at the end of the serial character frame. This must be set to match the stop bit setting on the host computer.

Parity

Possible Values: None*, Even, Odd

Parity None

This item selects the parity checking requirements for the serial data bits. This must be set to match the parity setting on the host computer.

Busy Signal Polarity

Possible Values: Low*, High

Busy Polarity Low

This item selects the polarity of the busy signal (pin 11 of the RS-232C interface). Busy is set whenever the printer is offline; the serial input buffer is full.

Data Terminal Ready

Possible Values: Power On/Off*

Online/Offline

Busy/Not Busy

DTR Power On/Off

Selects the condition to be reflected by the DTR signal (pin 20 of the RS- 232C interface). In most cases, especially those involving a MODEM, this

signal should be set to indicate Power On/Off. Selecting

57

Image 65

Printek 4000se manual Stop Bits, Parity None, Busy Polarity Low, DTR Power On/Off

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Introduction To Setup Common Error ConditionsError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Models and Options Introduction Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Print Server Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing The Ribbon Cartridge Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsPro 4300se & 4500se Single Tractor Model Loading Paper T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Introduction Daily Operation Control Panel Features LCD Display LCD Display and Indicators Online Control Panel Buttons Unload / Form Setup Loading a New or Different Form In the Tractors Selecting And Loading FormsSelecting a Form Already Loaded In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ ⎯0.30→ Down/Up Print 12345 No Paper to Load Common Error ConditionsCheck Paper Selected Form is not Loaded Too Much Paper to UnloadNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Setup Buttons Printer ConfigurationIntroduction To Setup Entering Setup Menus Entering SetupUsing the Setup Button Using the Function and Value Buttons Exiting Menus Saving Changes No Changes Exiting SetupExit Setup Yes Form Name Form Forms MenuForms Menu Items Automatic Cut No Tractor Path Front Lines/Inch Cut AdjustmentForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Characters/Inc h Bottom Margin 0 LinesLeft Margin Column Right Margin Column Impact Force Normal Font Epson FX FDDraft Speed Normal Zero Normal Language Unidirectional No Interface I/o Interface MenuEntering the Interface Menu Emulation Epson SerialAuto CR On Auto LF Off Minimum Buffer No Characters ControlBaud Rate Data Bits Stop Bits DTR Power On/OffParity None Busy Polarity Low ETX/ACK Off XON/XOFF Off Interface Menu Parallel/LAN LAN Setup OffParallel/LAN Interface Items IP Address IP Address AutoSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Max Form Allowed Auto-Scroll 1 Second DelayOptions Menu Paper Out Fault Finish Top of Barcode Off Char. To Ignore 255 Size 8192 Characters Top Oversized OffUser Language English Ribbon Check On Truncate Lines No ImagerPlus Graphic Card Ribbon Life Million CharsImagerPlus Emulation QMS CodeV Line Terminator ControlCharact 5E HexBar Code Density High-Res QMS Char Set Free Format Not Active PY Translation Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical Text Version Vertical DPICodeV SP Fields Process IGP Char Set Spacing IGP 10/20/40 Quiet Mode Not ActiveDelete Logos No Print Menus Test Mode OffTest Menu I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenancePage Page Align Print Edit Allowed Advanced Setup FeaturesSecurity Menu Options Menu Edit Allowed Forms Menu Edit AllowedInterface Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Introduction Using the Optional Setup ModuleSetup Module Installation New Setup Module Detected Initializing Setup ModuleCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code Escape Sequence Summaries Ansi X3.64 Emulation ESC * m n1 n2 data Epson Fx Emulation 100 ESC B n1 n2 ... nx NUL IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation ESC C Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page Print Speeds SpecificationsCharacter Matrix Graphics Density Character Spacing Character SetsLine Spacing Line Length Ribbon Special Forms Handling FeaturesComputer Interface 113 Warranty Operator Controls/IndicatorsReliability 114 115 Environmental SpecificationsOptions Page 117 Glossary of Terms 118 Ebcdic 119