Loading Paper | Printek 4000se specification

G E T T I N G S T A R T E D

Loading Paper

Please refer to the appropriate section below for loading paper in the FormsPro 4300se, 4500se, or 4503se.

FormsPro 4300se & 4500se Single Tractor Model

If the printer is not currently turned on, push the ON-1 side of the power switch on the right side of the printer. After you turn on the printer, it performs several self-tests.

Note: Paper is installed through the slot in the bottom of the printer.

1.To open the unit so you can install paper, pull outward on the bottom of the lower front panel of the printer as shown to release the latch.

Opening Latch Panel

14

Image 22

Printek 4000se manual Loading Paper, FormsPro 4300se & 4500se Single Tractor Model

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Error Messages Preventive Maintenance Obtaining Service Common Error ConditionsIntroduction To Setup Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting a Form Already Loaded In the Tractors Selecting And Loading FormsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Left/Right Aligning PrintAligning Print On Invoices ←0.00→ Down/Up Print ⎯0.30→ 12345 Check Paper Common Error ConditionsNo Paper to Load No Ribbon or Wrong Ribbon Too Much Paper to UnloadSelected Form is not Loaded Ribbon Lid Open Other Errors Page Introduction To Setup Printer ConfigurationSetup Buttons Using the Setup Button Entering SetupEntering Setup Menus Using the Function and Value Buttons Exit Setup Yes Exiting SetupExiting Menus Saving Changes No Changes Forms Menu Items Forms MenuForm Name Form Tractor Path Front Automatic Cut No Form Length 66 Lines Cut AdjustmentLines/Inch Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Left Margin Column Bottom Margin 0 LinesCharacters/Inc h Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Unidirectional No Entering the Interface Menu Interface MenuInterface I/o Auto CR On SerialEmulation Epson Auto LF Off Baud Rate Characters ControlMinimum Buffer No Data Bits Parity None DTR Power On/OffStop Bits Busy Polarity Low XON/XOFF Off ETX/ACK Off Parallel/LAN Interface Items LAN Setup OffInterface Menu Parallel/LAN Subnet Mask IP Address AutoIP Address IP Gateway Possible Values Off, On Minimum Buffer No Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off User Language English Top Oversized OffSize 8192 Characters Truncate Lines No Ribbon Check On ImagerPlus Ribbon Life Million CharsImagerPlus Graphic Card Emulation QMS CodeV Bar Code Density High-Res ControlCharact 5E HexLine Terminator QMS Char Set Ignore Data Not Active PY Translation Not ActiveFree Format Not Active Imager Zero Slashed CodeV SP Fields Process Vertical DPIVertical Text Version IGP Char Set Delete Logos No Quiet Mode Not ActiveSpacing IGP 10/20/40 Test Menu Test Mode OffPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Setup Module Installation Using the Optional Setup ModuleIntroduction Copying Setup to Printer Initializing Setup ModuleNew Setup Module Detected Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Character Matrix SpecificationsPrint Speeds Graphics Density Line Spacing Character SetsCharacter Spacing Line Length Computer Interface Special Forms Handling FeaturesRibbon 113 Reliability Operator Controls/IndicatorsWarranty 114 Options Environmental Specifications115 Page Glossary of Terms 117 Ebcdic 118 119