Entering Setup Menus, Form | Printek 4000se specification

P R I N T E R C O N F I G U R A T I O N

Entering Setup

To enter Setup, simply take the printer off line and press the SETUP button. The SETUP indicator will begin to flash yellow and the display will temporarily show the following.

Entering

Setup Menus

After the above message has been shown, the display will change to the first menu available, which is the FORMS MENU as shown below. In this case the display will also show which form is to be set up.

FORMS MENU

Form 0

Using the SETUP Button

At this time you may select a different menu by pressing the SETUP button. Other menus available are the INTERFACE MENU, the OPTIONS MENU, and the TEST MENU. This button will also display an option for exiting Setup. If you do not wish to exit Setup at this time, press either FUNCTION button. The SETUP button may be pressed at any time to select a different menu.

Using the FUNCTION and VALUE Buttons

Once the correct menu is selected, pressing either of the FUNCTION buttons will cause the various items and their current values to be displayed. Note that the items and their values are right justified and are thus controlled by the buttons to the right of the display. To scroll through the items available, use the FUNCTION buttons. To change the value of the displayed item, use the VALUE buttons to step through the possible choices. Remember to leave the correct value displayed before selecting a different item or menu, since “what you see is what you get” when Setup Mode is exited.

44

Image 52

Printek 4000se manual Entering Setup Menus, Form, Using the Setup Button, Using the Function and Value Buttons

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Common Error Conditions Introduction To SetupError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting a Form Already Loaded In the Tractors Selecting And Loading FormsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Print ⎯0.30→ 12345 Check Paper Common Error ConditionsNo Paper to Load Too Much Paper to Unload Selected Form is not LoadedNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Introduction To Setup Printer ConfigurationSetup Buttons Entering Setup Entering Setup MenusUsing the Setup Button Using the Function and Value Buttons Exit Setup Yes Exiting SetupExiting Menus Saving Changes No Changes Forms Menu Items Forms MenuForm Name Form Tractor Path Front Automatic Cut No Cut Adjustment Lines/InchForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Bottom Margin 0 Lines Characters/Inc hLeft Margin Column Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Unidirectional No Entering the Interface Menu Interface MenuInterface I/o Serial Emulation EpsonAuto CR On Auto LF Off Characters Control Minimum Buffer NoBaud Rate Data Bits DTR Power On/Off Stop BitsParity None Busy Polarity Low XON/XOFF Off ETX/ACK Off Parallel/LAN Interface Items LAN Setup OffInterface Menu Parallel/LAN IP Address Auto IP AddressSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off User Language English Top Oversized OffSize 8192 Characters Truncate Lines No Ribbon Check On Ribbon Life Million Chars ImagerPlus Graphic CardImagerPlus Emulation QMS CodeV ControlCharact 5E Hex Line TerminatorBar Code Density High-Res QMS Char Set PY Translation Not Active Free Format Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical DPI Vertical Text VersionCodeV SP Fields Process IGP Char Set Delete Logos No Quiet Mode Not ActiveSpacing IGP 10/20/40 Test Menu Test Mode OffPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Setup Module Installation Using the Optional Setup ModuleIntroduction Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Specifications Print SpeedsCharacter Matrix Graphics Density Character Sets Character SpacingLine Spacing Line Length Special Forms Handling Features RibbonComputer Interface 113 Operator Controls/Indicators WarrantyReliability 114 Options Environmental Specifications115 Page Glossary of Terms 117 Ebcdic 118 119