Using the Optional Setup Module, Introduction | Printek 4000se

USING THE OPTIONAL SETUP

MODULE

Introduction

The optional Setup Module is a small cartridge that plugs directly into the RS-232 Serial connector on the rear of any FormsPro 4000se series printer. This module is used to store a second copy of the current Setup configuration of the printer. This may then be used to restore settings after a printer is serviced or to copy the same configuration settings to another printer. These uses are discussed immediately following the installation instructions.

Setup Module Installation

To install the Setup Module, perform the following steps.

1.Turn off power to the printer.

2.Disconnect the cable plugged into the serial port if one is present.

3.Plug the Setup Module into the serial port.

4.If a cable was present in step 2, reconnect it to the connector on the rear of the Setup Module.

5.Turn on power to the printer.

6.If this is not the first time the Setup Module has been connected to a printer, then proceed with step 7.

If this is the first time the Setup Module has ever been attached to a printer, the printer will temporarily display the following message.

91

Image 99

Printek 4000se manual Using the Optional Setup Module, Introduction, Setup Module Installation

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Forms Menu Common Error ConditionsIntroduction To Setup Error Messages Preventive Maintenance Obtaining Service Vii Page Models and Options Introduction Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Print Server Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing The Ribbon Cartridge Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsPro 4300se & 4500se Single Tractor Model Loading Paper T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Introduction Daily Operation Control Panel Features LCD Display LCD Display and Indicators Online Control Panel Buttons Unload / Form Setup Selecting And Loading Forms Selecting a Form Already Loaded In the TractorsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation ←0.00→ Aligning PrintAligning Print On Invoices Left/Right ⎯0.30→ Down/Up Print 12345 Common Error Conditions Check PaperNo Paper to Load Ribbon Lid Open Too Much Paper to UnloadSelected Form is not Loaded No Ribbon or Wrong Ribbon Other Errors Page Printer Configuration Introduction To SetupSetup Buttons Using the Function and Value Buttons Entering SetupEntering Setup Menus Using the Setup Button Exiting Setup Exit Setup YesExiting Menus Saving Changes No Changes Forms Menu Forms Menu ItemsForm Name Form Automatic Cut No Tractor Path Front Top Margin 0 Lines Cut AdjustmentLines/Inch Form Length 66 Lines I N T E R C O N F I G U R a T I O N Right Margin Column Bottom Margin 0 LinesCharacters/Inc h Left Margin Column Font Epson FX FD Draft Speed NormalImpact Force Normal Zero Normal Language Unidirectional No Interface Menu Entering the Interface MenuInterface I/o Auto LF Off SerialEmulation Epson Auto CR On Data Bits Characters ControlMinimum Buffer No Baud Rate Busy Polarity Low DTR Power On/OffStop Bits Parity None ETX/ACK Off XON/XOFF Off LAN Setup Off Parallel/LAN Interface ItemsInterface Menu Parallel/LAN IP Gateway IP Address AutoIP Address Subnet Mask Possible Values Off, On Minimum Buffer No Auto-Scroll 1 Second Delay Options MenuMax Form Allowed Paper Out Fault Finish Top of Barcode Off Char. To Ignore 255 Top Oversized Off User Language EnglishSize 8192 Characters Ribbon Check On Truncate Lines No Emulation QMS CodeV Ribbon Life Million CharsImagerPlus Graphic Card ImagerPlus QMS Char Set ControlCharact 5E HexLine Terminator Bar Code Density High-Res Imager Zero Slashed PY Translation Not ActiveFree Format Not Active Ignore Data Not Active IGP Char Set Vertical DPIVertical Text Version CodeV SP Fields Process Quiet Mode Not Active Delete Logos NoSpacing IGP 10/20/40 Test Mode Off Test MenuPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenancePage Page Advanced Setup Features Security MenuAlign Print Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Using the Optional Setup Module Setup Module InstallationIntroduction Load = Read Unload = Write Initializing Setup ModuleNew Setup Module Detected Copying Setup to Printer Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code Escape Sequence Summaries Ansi X3.64 Emulation ESC * m n1 n2 data Epson Fx Emulation 100 ESC B n1 n2 ... nx NUL IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation ESC C Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page Graphics Density SpecificationsPrint Speeds Character Matrix Line Length Character SetsCharacter Spacing Line Spacing 113 Special Forms Handling FeaturesRibbon Computer Interface 114 Operator Controls/IndicatorsWarranty Reliability Environmental Specifications Options115 Page 117 Glossary of Terms 118 Ebcdic 119