ControlCharact 5E Hex, Line Terminator | Printek 4000se specification

P R I N T E R C O N F I G U R A T I O N

Control Character

Possible Values: ^ (5E Hex)*

ControlCharact

er

^ (5E Hex)

SOH (01 Hex) through HT (09 Hex),

SO (0E Hex) through (FF Hex)

This item sets the control character used to begin commands. The character normally used for QMS is the caret (^) and the character normally used for IGP is the tilde (~) (if you change the emulation to Printronix IGP, you may need to change the control character to the tilde).

Line Terminator

Possible Values: LF*, CR

Line

Terminator

LF

This item sets the line terminating character to a Line Feed or a Carriage Return.

Bar Code Density

Bar Code

Density

High-Res

Possible Values: Low-Res, Medium-Res, High-Res*,

Graphics Med-Res

This item sets the density, or graphics resolution, for bar codes.

QMS Character Set		QMS Char Set
(QMS CodeV v2 and PTX CodeV v2 only)		USA
Possible Values: USA	France
United Kingdom	Italy
Sweden/Finland	Spain
Norway/Denmark	PC Subset
Japan	CodeV Version1
Germany

69

Image 77

Printek 4000se manual ControlCharact 5E Hex, Line Terminator, Bar Code Density High-Res, QMS Char Set

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Introduction To Setup Common Error ConditionsError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Models and Options Introduction Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Print Server Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing The Ribbon Cartridge Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsPro 4300se & 4500se Single Tractor Model Loading Paper T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Introduction Daily Operation Control Panel Features LCD Display LCD Display and Indicators Online Control Panel Buttons Unload / Form Setup Loading a New or Different Form In the Tractors Selecting And Loading FormsSelecting a Form Already Loaded In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ ⎯0.30→ Down/Up Print 12345 No Paper to Load Common Error ConditionsCheck Paper Selected Form is not Loaded Too Much Paper to UnloadNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Setup Buttons Printer ConfigurationIntroduction To Setup Entering Setup Menus Entering SetupUsing the Setup Button Using the Function and Value Buttons Exiting Menus Saving Changes No Changes Exiting SetupExit Setup Yes Form Name Form Forms MenuForms Menu Items Automatic Cut No Tractor Path Front Lines/Inch Cut AdjustmentForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Characters/Inc h Bottom Margin 0 LinesLeft Margin Column Right Margin Column Impact Force Normal Font Epson FX FDDraft Speed Normal Zero Normal Language Unidirectional No Interface I/o Interface MenuEntering the Interface Menu Emulation Epson SerialAuto CR On Auto LF Off Minimum Buffer No Characters ControlBaud Rate Data Bits Stop Bits DTR Power On/OffParity None Busy Polarity Low ETX/ACK Off XON/XOFF Off Interface Menu Parallel/LAN LAN Setup OffParallel/LAN Interface Items IP Address IP Address AutoSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Max Form Allowed Auto-Scroll 1 Second DelayOptions Menu Paper Out Fault Finish Top of Barcode Off Char. To Ignore 255 Size 8192 Characters Top Oversized OffUser Language English Ribbon Check On Truncate Lines No ImagerPlus Graphic Card Ribbon Life Million CharsImagerPlus Emulation QMS CodeV Line Terminator ControlCharact 5E HexBar Code Density High-Res QMS Char Set Free Format Not Active PY Translation Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical Text Version Vertical DPICodeV SP Fields Process IGP Char Set Spacing IGP 10/20/40 Quiet Mode Not ActiveDelete Logos No Print Menus Test Mode OffTest Menu I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenancePage Page Align Print Edit Allowed Advanced Setup FeaturesSecurity Menu Options Menu Edit Allowed Forms Menu Edit AllowedInterface Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Introduction Using the Optional Setup ModuleSetup Module Installation New Setup Module Detected Initializing Setup ModuleCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code Escape Sequence Summaries Ansi X3.64 Emulation ESC * m n1 n2 data Epson Fx Emulation 100 ESC B n1 n2 ... nx NUL IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation ESC C Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page Print Speeds SpecificationsCharacter Matrix Graphics Density Character Spacing Character SetsLine Spacing Line Length Ribbon Special Forms Handling FeaturesComputer Interface 113 Warranty Operator Controls/IndicatorsReliability 114 115 Environmental SpecificationsOptions Page 117 Glossary of Terms 118 Ebcdic 119