Paper Out Fault Finish | Printek 4000se specification

P R I N T E R C O N F I G U R A T I O N

since the last print operation) and a form boundary (bottom of the form according to the Form Length setting for the current form) has been reached. If printing finishes and the form boundary has not been reached, take the printer off line and the FORM FEED button may be used to advance the form to the tear bar. This item may also be used to disable Auto-Scroll by setting the value to Off. When disabled, the FORM FEED button must always be used to advance the form to the tear bar.

Paper Out Fault Action

Possible Values: Finish Page*

Reprint Page

Break Page

Paper Out

Fault

Finish Page

This item selects what action is to be taken when a paper out condition occurs. The action taken for each of the possible values is described in the following paragraphs.

When Finish Page is selected, the printer will attempt to print to the bottom of the page when a normal paper out condition occurs. Conditions that will prevent this from happening are when the end of paper is detected too far from the end of the form (the printer assumes there is not a complete page available), when reverse paper motion is attempted within the last one inch of the form, or when a paper jam occurs. If the printer is unable to finish printing the page, it will attempt to reprint the page as described below (also refer to the Reprint Page Size option which follows). Note that if highly precise printing is required in the last inch of the form, Finish Page may not provide accurate enough paper motion since the form is no longer controlled by the tractor mechanism.

When Reprint Page is selected, the printer will stop printing as soon as the end of paper or a paper jam condition is detected and the printer will go off line. After a new box of forms is loaded, the printer will attempt to reprint the current page from the beginning. If the printer is able to reprint the page, Reprinting Page! will be displayed when the new form is loaded (the previous partially printed page should probably be discarded). If the printer is unable to reprint the page, the page will be broken, Cannot Reprint - Page Too Large will be displayed, and

64

Image 72

Printek 4000se manual Paper Out Fault Finish

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Common Error Conditions Introduction To SetupError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting And Loading Forms Selecting a Form Already Loaded In the TractorsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Print ⎯0.30→ 12345 Common Error Conditions Check PaperNo Paper to Load Too Much Paper to Unload Selected Form is not LoadedNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Printer Configuration Introduction To SetupSetup Buttons Entering Setup Entering Setup MenusUsing the Setup Button Using the Function and Value Buttons Exiting Setup Exit Setup YesExiting Menus Saving Changes No Changes Forms Menu Forms Menu ItemsForm Name Form Tractor Path Front Automatic Cut No Cut Adjustment Lines/InchForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Bottom Margin 0 Lines Characters/Inc hLeft Margin Column Right Margin Column Font Epson FX FD Draft Speed NormalImpact Force Normal Language Zero Normal Unidirectional No Interface Menu Entering the Interface MenuInterface I/o Serial Emulation EpsonAuto CR On Auto LF Off Characters Control Minimum Buffer NoBaud Rate Data Bits DTR Power On/Off Stop BitsParity None Busy Polarity Low XON/XOFF Off ETX/ACK Off LAN Setup Off Parallel/LAN Interface ItemsInterface Menu Parallel/LAN IP Address Auto IP AddressSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Auto-Scroll 1 Second Delay Options MenuMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off Top Oversized Off User Language EnglishSize 8192 Characters Truncate Lines No Ribbon Check On Ribbon Life Million Chars ImagerPlus Graphic CardImagerPlus Emulation QMS CodeV ControlCharact 5E Hex Line TerminatorBar Code Density High-Res QMS Char Set PY Translation Not Active Free Format Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical DPI Vertical Text VersionCodeV SP Fields Process IGP Char Set Quiet Mode Not Active Delete Logos NoSpacing IGP 10/20/40 Test Mode Off Test MenuPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Advanced Setup Features Security MenuAlign Print Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Using the Optional Setup Module Setup Module InstallationIntroduction Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Specifications Print SpeedsCharacter Matrix Graphics Density Character Sets Character SpacingLine Spacing Line Length Special Forms Handling Features RibbonComputer Interface 113 Operator Controls/Indicators WarrantyReliability 114 Environmental Specifications Options115 Page Glossary of Terms 117 Ebcdic 118 119