I L Y O P E R a T I O N | Printek 4000se instruction

D A I L Y O P E R A T I O N

paths, proceed to step 4 on the following page. You can position the other tractor paths for loading without closing the printer's case.

To load another tractor path:

1.Press the UNLOAD/FORM SELECT button on the front panel until the desired form and tractor path is indicated on the LCD display.

2.Then press the LOAD button. This causes the selected tractors to move into position for loading.

3.You may now install the paper in this tractor path.

28

Image 36

Printek 4000se manual I L Y O P E R a T I O N

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Common Error Conditions Introduction To SetupError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting And Loading Forms Selecting a Form Already Loaded In the TractorsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Print ⎯0.30→ 12345 Common Error Conditions Check PaperNo Paper to Load Too Much Paper to Unload Selected Form is not LoadedNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Printer Configuration Introduction To SetupSetup Buttons Entering Setup Entering Setup MenusUsing the Setup Button Using the Function and Value Buttons Exiting Setup Exit Setup YesExiting Menus Saving Changes No Changes Forms Menu Forms Menu ItemsForm Name Form Tractor Path Front Automatic Cut No Cut Adjustment Lines/InchForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Bottom Margin 0 Lines Characters/Inc hLeft Margin Column Right Margin Column Font Epson FX FD Draft Speed NormalImpact Force Normal Language Zero Normal Unidirectional No Interface Menu Entering the Interface MenuInterface I/o Serial Emulation EpsonAuto CR On Auto LF Off Characters Control Minimum Buffer NoBaud Rate Data Bits DTR Power On/Off Stop BitsParity None Busy Polarity Low XON/XOFF Off ETX/ACK Off LAN Setup Off Parallel/LAN Interface ItemsInterface Menu Parallel/LAN IP Address Auto IP AddressSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Auto-Scroll 1 Second Delay Options MenuMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off Top Oversized Off User Language EnglishSize 8192 Characters Truncate Lines No Ribbon Check On Ribbon Life Million Chars ImagerPlus Graphic CardImagerPlus Emulation QMS CodeV ControlCharact 5E Hex Line TerminatorBar Code Density High-Res QMS Char Set PY Translation Not Active Free Format Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical DPI Vertical Text VersionCodeV SP Fields Process IGP Char Set Quiet Mode Not Active Delete Logos NoSpacing IGP 10/20/40 Test Mode Off Test MenuPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Advanced Setup Features Security MenuAlign Print Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Using the Optional Setup Module Setup Module InstallationIntroduction Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Specifications Print SpeedsCharacter Matrix Graphics Density Character Sets Character SpacingLine Spacing Line Length Special Forms Handling Features RibbonComputer Interface 113 Operator Controls/Indicators WarrantyReliability 114 Environmental Specifications Options115 Page Glossary of Terms 117 Ebcdic 118 119