Control Panel Features | Printek 4000se specs

D A I L Y O P E R A T I O N

Control Panel Features

This section assumes that your printer has already been installed according to the information in “Installation and Interface Setup”, and describes the daily operation of the FormsPro 4000se series printers. In particular, using the control panel, changing paper or forms, and changing the ribbon cartridge are discussed.

Control Panel

The FormsPro 4000se series printers feature an intuitive, easy-to-use control panel that provides immediate access to the controls required by most operators. Individual indicators are available which provide a quick indication of printer status, as well as a two line by sixteen-character display, which provides even more status information.

Many more features, including form and interface parameters, are available through the SETUP mode. All features, which are modified during setup, are stored in nonvolatile memory and are used each time the printer is turned on or reset. For more information, refer to the appendix on

“PRINTER RESET CONDITIONS”.

The printer's control panel consists of six pushbutton switches, four LED indicators, and a two line by 16-character LCD display as shown above.

The pushbutton switches (or buttons), the LCD display, and the LED indicators provide you with the following controls and status information:

20

Image 28

Printek 4000se manual Control Panel Features

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Common Error Conditions Introduction To SetupError Messages Preventive Maintenance Obtaining Service Forms Menu Vii Page Introduction Models and Options Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Print Server Installing The Ribbon Cartridge Why Use Only Printek Brand Ribbons Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsPro 4300se & 4500se Single Tractor Model T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Daily Operation Introduction Control Panel Features LCD Display and Indicators LCD Display Control Panel Buttons Online Unload / Form Setup Selecting a Form Already Loaded In the Tractors Selecting And Loading FormsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Print ⎯0.30→ 12345 Check Paper Common Error ConditionsNo Paper to Load Too Much Paper to Unload Selected Form is not LoadedNo Ribbon or Wrong Ribbon Ribbon Lid Open Other Errors Page Introduction To Setup Printer ConfigurationSetup Buttons Entering Setup Entering Setup MenusUsing the Setup Button Using the Function and Value Buttons Exit Setup Yes Exiting SetupExiting Menus Saving Changes No Changes Forms Menu Items Forms MenuForm Name Form Tractor Path Front Automatic Cut No Cut Adjustment Lines/InchForm Length 66 Lines Top Margin 0 Lines I N T E R C O N F I G U R a T I O N Bottom Margin 0 Lines Characters/Inc hLeft Margin Column Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Unidirectional No Entering the Interface Menu Interface MenuInterface I/o Serial Emulation EpsonAuto CR On Auto LF Off Characters Control Minimum Buffer NoBaud Rate Data Bits DTR Power On/Off Stop BitsParity None Busy Polarity Low XON/XOFF Off ETX/ACK Off Parallel/LAN Interface Items LAN Setup OffInterface Menu Parallel/LAN IP Address Auto IP AddressSubnet Mask IP Gateway Possible Values Off, On Minimum Buffer No Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Paper Out Fault Finish Char. To Ignore 255 Top of Barcode Off User Language English Top Oversized OffSize 8192 Characters Truncate Lines No Ribbon Check On Ribbon Life Million Chars ImagerPlus Graphic CardImagerPlus Emulation QMS CodeV ControlCharact 5E Hex Line TerminatorBar Code Density High-Res QMS Char Set PY Translation Not Active Free Format Not ActiveIgnore Data Not Active Imager Zero Slashed Vertical DPI Vertical Text VersionCodeV SP Fields Process IGP Char Set Delete Logos No Quiet Mode Not ActiveSpacing IGP 10/20/40 Test Menu Test Mode OffPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServicePage Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Setup Module Installation Using the Optional Setup ModuleIntroduction Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Load = Read Unload = Write Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi X3.64 Emulation Epson Fx Emulation ESC * m n1 n2 data ESC B n1 n2 ... nx NUL 100 IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek Emulation ESC C Ascii Character Tables 105 106 107 108 109 Page Specifications Print SpeedsCharacter Matrix Graphics Density Character Sets Character SpacingLine Spacing Line Length Special Forms Handling Features RibbonComputer Interface 113 Operator Controls/Indicators WarrantyReliability 114 Options Environmental Specifications115 Page Glossary of Terms 117 Ebcdic 118 119