Parallel/LAN Interface Items, LAN Setup Off | Printek 4000se

P R I N T E R C O N F I G U R A T I O N

Parallel/LAN Interface Items

Since the optional LAN interface goes into the Parallel port, these interface

parameters are the same.

INTERFACE MENU Parallel/LAN

Emulation

Emulation Epson

Possible Values: Epson*, IBM Proprinter, DEC LA120/210,

TTY, Printek, ANSI X3.64,

Genicom 3840, Genicom 3410

This item selects the emulation to be used whenever the parallel port is active. The emulation should be set to match the type of printer your software supports.

LAN Setup

Possible Values: On, Off*

LAN Setup Off

This item enables or disables the ability to control the optional Ethernet interface card from the front panel. When set to On, the Serial Interface is not available, and menu items for the Ethernet card follow. Consult your Network Administrator before changing any of these items.

Note: Setting this item to On when the optional Ethernet interface card or optional control loop-back cable is not present, may result in the printer appearing to “hang” when exiting the Setup Menus. After 15 seconds, a LAN Timeout error will be displayed. Press ONLINE, then enter the Setup Menus and correct the problem.

59

Image 67

Printek 4000se manual Parallel/LAN Interface Items, Interface Menu Parallel/LAN, LAN Setup Off

Contents

FormsPro 4000se Series Operator’s Manual Page Iii Page Table of Contents Forms Menu Common Error ConditionsIntroduction To Setup Error Messages Preventive Maintenance Obtaining Service Vii Page Models and Options Introduction Manual Contents ∙ Control Code and Escape Sequence Summaries lists Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Print Server Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing The Ribbon Cartridge Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsPro 4300se & 4500se Single Tractor Model Loading Paper T T I N G S T a R T E D FormsPro 4503se Tri-Trak Model T T I N G S T a R T E D Printer Self-Test Introduction Daily Operation Control Panel Features LCD Display LCD Display and Indicators Online Control Panel Buttons Unload / Form Setup Selecting a Form Already Loaded In the Tractors Selecting And Loading FormsLoading a New or Different Form In the Tractors Changing the Form in the Tractors FormsPro 4503se With Forms Installed Front Tractor Path I L Y O P E R a T I O N Changing to a Form Installed in Another Path Ejecting And Tearing Off a Form Positioning the Form for Tear Off Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Installing the New Ribbon Cartridge Ribbon Cartridge Installation ←0.00→ Aligning PrintAligning Print On Invoices Left/Right ⎯0.30→ Down/Up Print 12345 Check Paper Common Error ConditionsNo Paper to Load Ribbon Lid Open Too Much Paper to UnloadSelected Form is not Loaded No Ribbon or Wrong Ribbon Other Errors Page Introduction To Setup Printer ConfigurationSetup Buttons Using the Function and Value Buttons Entering SetupEntering Setup Menus Using the Setup Button Exit Setup Yes Exiting SetupExiting Menus Saving Changes No Changes Forms Menu Items Forms MenuForm Name Form Automatic Cut No Tractor Path Front Top Margin 0 Lines Cut AdjustmentLines/Inch Form Length 66 Lines I N T E R C O N F I G U R a T I O N Right Margin Column Bottom Margin 0 LinesCharacters/Inc h Left Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Zero Normal Language Unidirectional No Entering the Interface Menu Interface MenuInterface I/o Auto LF Off SerialEmulation Epson Auto CR On Data Bits Characters ControlMinimum Buffer No Baud Rate Busy Polarity Low DTR Power On/OffStop Bits Parity None ETX/ACK Off XON/XOFF Off Parallel/LAN Interface Items LAN Setup OffInterface Menu Parallel/LAN IP Gateway IP Address AutoIP Address Subnet Mask Possible Values Off, On Minimum Buffer No Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Paper Out Fault Finish Top of Barcode Off Char. To Ignore 255 User Language English Top Oversized OffSize 8192 Characters Ribbon Check On Truncate Lines No Emulation QMS CodeV Ribbon Life Million CharsImagerPlus Graphic Card ImagerPlus QMS Char Set ControlCharact 5E HexLine Terminator Bar Code Density High-Res Imager Zero Slashed PY Translation Not ActiveFree Format Not Active Ignore Data Not Active IGP Char Set Vertical DPIVertical Text Version CodeV SP Fields Process Delete Logos No Quiet Mode Not ActiveSpacing IGP 10/20/40 Test Menu Test Mode OffPrint Menus I N T E R C O N F I G U R a T I O N Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenancePage Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Line Definitions I N G R E M O T E S E T U P I N G R E M O T E S E T U P Remote Setup Example File Page Setup Module Installation Using the Optional Setup ModuleIntroduction Load = Read Unload = Write Initializing Setup ModuleNew Setup Module Detected Copying Setup to Printer Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code Escape Sequence Summaries Ansi X3.64 Emulation ESC * m n1 n2 data Epson Fx Emulation 100 ESC B n1 n2 ... nx NUL IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation ESC C Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page Graphics Density SpecificationsPrint Speeds Character Matrix Line Length Character SetsCharacter Spacing Line Spacing 113 Special Forms Handling FeaturesRibbon Computer Interface 114 Operator Controls/IndicatorsWarranty Reliability Options Environmental Specifications115 Page 117 Glossary of Terms 118 Ebcdic 119