Control Panel Features | Printek 8000SE manual

D A I L Y O P E R A T I O N

Control Panel Features

The following picture shows the printer’s control panel. The control panel consists of a two line LCD display, an ONLINE status indicator, nine push button switches or “buttons”, and a speaker. Each of these items is described below

SETU MENU

ALIGN SUB-

PRINT MENU

LCD

DISPLAY

ITEM

VALUE

FORM FOR

SELEC M ON

T FEED LINE

UNLOA

	Control Panel
LCD Display and Online Indicator
LCD Display	This two line by sixteen character display is used
	to convey several types of information. When the
	printer is on line and printing, or ready to print,
	the display will show the currently selected
	tractor path and the form currently loaded in that
	path. When the printer is off line, the display will

continue to show this information, additional information based upon other buttons being pressed by the operator, or error conditions such as “Check Paper”.

ONLINE Status

Indicator LED

Green:

This is a multicolored LED which is used to display the following information:

The printer is on line and ready to print.

22

Image 30

Printek 8000SE manual Control Panel Features, LCD Display and Online Indicator, Display will show the currently selected

Contents

FormsMaster 8000se Series Part Number Specifications are subject to change without notice IiiPage Page Table of Contents Error Messages Preventive Maintenance Obtaining Service Common Error ConditionsIntroduction To Setup Forms Menu 102 Simple TTY Emulation 103 Printek Emulation 104Viii Introduction Models and Options Manual Contents Page Page Installation Getting Started Interface Set Up Pin Signal RS-232C Serial Interface Parallel Interface Wireless Ethernet Print Server Ethernet 10/100BaseT Installing the Ribbon Cartridge Why Use Only Printek Brand Ribbons T T I N G S T a R T E D Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsMaster 8000se Single Tractor ModelOpen the doors on each tractor FormsMaster 8003se TriTrak Model Loading the Front Tractors Loading the Center Tractors Printer Self-Test Selecting Which Form to Print T T I N G S T a R T E D Daily Operation Introduction Control Panel Features LCD Display and Online IndicatorDisplay will show the currently selected I L Y O P E R a T I O N Control Panel Buttons Configuration for more information This button is used to access up to ten differentForms which have been previously configured Move forward for easy access to all tractors To access the vertical adjustment, press either When Align Print is pressed, the horizontalAdjustment is shown first. Pressing the Value Form Selecting and Loading Forms Selecting a Form Already Loaded in the TractorsLoading a New or Different Form In the Tractors Loading the Form in the Tractors Open the tractor doors and remove the old form Paper positioned in left tractor New form loaded in tractors Ejecting And Tearing Off a Form Tearing off a form Installing a New Ribbon Cartridge Removing the Old Ribbon Cartridge Installing the New Ribbon Cartridge Close the ribbon lid and place printer back on line Left/Right Aligning PrintAligning Print On Invoices ←0.00→ Down/Up Print ⎯0.30→ Common Error Conditions Check Paper Selected Form is Not Loaded No Paper to LoadToo Much Paper to Unload No Ribbon or Wrong Ribbon Paper Door Open Other ErrorsRibbon Lid Open Change Ribbon Printer Configuration Introduction To SetupSetup Buttons Using the Menu Button Entering SetupEntering Setup Menus Using the Submenu Button ←No Exit Setup ←Yes Menus? Using the Item and Value ButtonsExiting Setup Exiting Menus Saving Changes No Changes Forms Menu Forms Menu Items Form Name FormTractor Path Front Lines/Inch Cut AdjustmentAutomatic Cut No Form Length 66 Lines Top Margin 0 Lines Possible Values 0* … 226 LinesBottom Margin 0 Lines Possible Values Column 4 … Possible Values Column 0* …Left Margin Column Right Margin Column Impact Force Normal Font Epson FX FDDraft Speed Normal Language Possible Values No*, Yes Possible Values Normal*, SlashedZero Normal Unidirectional No Interface Menu Entering the Interface MenuSerial Auto CR On RS-232C Serial Interface ItemsEmulation Epson Auto LF Off Baud Rate Characters ControlMinimum Buffer No Data Bits Parity None DTR Power On/OffStop Bits Busy Polarity Low Possible Values Power On/Off XON/XOFF OffETX/ACK Off I N T E R C O N F I G U R a T I O N Parallel/LAN LAN Setup OffParallel/LAN Interface Items Possible Values On, Off IP Address Subnet MaskIP Gateway Auto LF Off Auto-Scroll 1 Second Delay Options MenuMax Form Allowed Paper Out Fault Finish Possible Values Finish Possible Values 0, … Char. To Ignore 255 User Language English Top of Barcode OffTop Oversized Off Size 8192 Characters Possible Values On*, Off Possible Values Yes, NoTruncate Lines No Ribbon Check On ImagerPlus Ribbon Life Million CharsImagerPlus Graphic Card Emulation QMS CodeV Bar Code Density High-Res ControlCharact 5E HexLine Terminator QMS Char Set Free Format Not Active Ignore Data Not ActiveImager Zero Slashed Vertical Text Version LineRegistrati Not MaintainedVertical DPI CodeV SP Fields Process Test Menu Quiet Mode Not ActiveThis item selects the Spacing mode Delete Logos No Test Mode Off Print Menus I N T E R C O N F I G U R a T I O N Page Form Construction Form Construction Form Layout Considerations Maintenance Troubleshooting Error Messages Preventive Maintenance Obtaining ServiceError Message Page Page Advanced Setup Features Security MenuAlign Print Edit Allowed V a N C E D S E T U P F E a T U R E S Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Page Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Page Remote Setup Example File Page Page Using the Optional Setup Module Setup Module InstallationIntroduction Initializing Setup Module New Setup Module Detected←Copy to Printer ←Copy to Module Copying Setup to Printer Copying Setup To Module I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Control Code and Escape Sequence Summaries Genicom 3840 and 3410 Emulation Ansi x3.64 Emulation Epson FX Emulation 100 IBM Proprinter Emulation Delete ESC @ n1 n2 m1 m2 m3 m4 Double-High ModeESC \ n1 n2 Print Characters ESC n Print Single Character ESC a Simple TTY Emulation Printek Emulation Ascii Character Tables 105 106 107 108 109 Page Specifications 60 to 240 dpi horizontally x 72 dpi vertically111 Inches 112 23,000,000 character, mobius loop cartridge 113 Printer Workmanship114 115 116 Glossary of Terms 117 118 Online Refers to the state of the printer when Able to respond to the commands and textPrinter is powered on default value Received from the host computer