Test Menu, Delete Logos No, Quiet Mode Not Active | Printek 8000SE

P R I N T E R C O N F I G U R A T I O N

Denmark Spain

NorwayItaly

Finland Turkey

This item selects the character set.

Delete Logos

Delete Logos No

Possible Values: No*, Yes

This item selects whether logos should be deleted when a form is deleted.

Quiet Mode

Quiet Mode Not Active

Possible Values: Not Active*, Active

This item selects whether or not the quiet mode is active at power on.

Spacing Mode

Spacing IGP 10/20/40

Possible Values: IGP 10/20/40*, IGP 30

This item selects the Spacing mode.

Test Menu

The TEST MENU is used to access some testing as well as some record keeping items. To access the test menu, enter Setup and press the MENU button until TEST MENU is displayed as shown below.

TEST MENU

Next press either of the ITEM buttons to access the test modes available.

69

Image 77

Printek 8000SE Test Menu, Delete Logos No, Quiet Mode Not Active, Spacing IGP 10/20/40, This item selects the Spacing mode

Contents

FormsMaster 8000se Series Part Number Iii Specifications are subject to change without noticePage Page Table of Contents Introduction To Setup Common Error ConditionsError Messages Preventive Maintenance Obtaining Service Forms Menu Viii 102Simple TTY Emulation 103 Printek Emulation 104 Models and Options Introduction Manual Contents Page Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing the Ribbon Cartridge T T I N G S T a R T E D Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Open the doors on each tractor Loading PaperFormsMaster 8000se Single Tractor Model FormsMaster 8003se TriTrak Model Loading the Front Tractors Loading the Center Tractors Selecting Which Form to Print Printer Self-Test T T I N G S T a R T E D Introduction Daily Operation Display will show the currently selected Control Panel FeaturesLCD Display and Online Indicator I L Y O P E R a T I O N Control Panel Buttons Forms which have been previously configured This button is used to access up to ten differentConfiguration for more information Move forward for easy access to all tractors Adjustment is shown first. Pressing the Value When Align Print is pressed, the horizontalTo access the vertical adjustment, press either Form Loading a New or Different Form In the Tractors Selecting and Loading FormsSelecting a Form Already Loaded in the Tractors Loading the Form in the Tractors Open the tractor doors and remove the old form Paper positioned in left tractor New form loaded in tractors Ejecting And Tearing Off a Form Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Close the ribbon lid and place printer back on line Installing the New Ribbon Cartridge Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ ⎯0.30→ Down/Up Print Check Paper Common Error Conditions Too Much Paper to Unload No Paper to LoadSelected Form is Not Loaded No Ribbon or Wrong Ribbon Ribbon Lid Open Other ErrorsPaper Door Open Change Ribbon Setup Buttons Printer ConfigurationIntroduction To Setup Entering Setup Menus Entering SetupUsing the Menu Button Using the Submenu Button Exiting Setup Using the Item and Value Buttons←No Exit Setup ←Yes Menus? Exiting Menus Saving Changes No Changes Forms Menu Tractor Path Front Forms Menu ItemsForm Name Form Automatic Cut No Cut AdjustmentLines/Inch Form Length 66 Lines Bottom Margin 0 Lines Top Margin 0 LinesPossible Values 0* … 226 Lines Left Margin Column Possible Values Column 0* …Possible Values Column 4 … Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Possible Values Normal*, SlashedPossible Values No*, Yes Unidirectional No Serial Interface MenuEntering the Interface Menu Emulation Epson RS-232C Serial Interface ItemsAuto CR On Auto LF Off Minimum Buffer No Characters ControlBaud Rate Data Bits Stop Bits DTR Power On/OffParity None Busy Polarity Low ETX/ACK Off Possible Values Power On/OffXON/XOFF Off I N T E R C O N F I G U R a T I O N Parallel/LAN Interface Items LAN Setup OffParallel/LAN Possible Values On, Off IP Gateway IP AddressSubnet Mask Auto LF Off Max Form Allowed Auto-Scroll 1 Second DelayOptions Menu Possible Values Finish Paper Out Fault Finish Char. To Ignore 255 Possible Values 0, … Top Oversized Off Top of Barcode OffUser Language English Size 8192 Characters Truncate Lines No Possible Values Yes, NoPossible Values On*, Off Ribbon Check On ImagerPlus Graphic Card Ribbon Life Million CharsImagerPlus Emulation QMS CodeV Line Terminator ControlCharact 5E HexBar Code Density High-Res QMS Char Set Imager Zero Slashed Free Format Not ActiveIgnore Data Not Active Vertical DPI LineRegistrati Not MaintainedVertical Text Version CodeV SP Fields Process This item selects the Spacing mode Quiet Mode Not ActiveTest Menu Delete Logos No Print Menus Test Mode Off I N T E R C O N F I G U R a T I O N Page Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Error Message Preventive MaintenanceObtaining Service Page Page Align Print Edit Allowed Advanced Setup FeaturesSecurity Menu V a N C E D S E T U P F E a T U R E S Options Menu Edit Allowed Forms Menu Edit AllowedInterface Menu Edit Allowed Page Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Page Remote Setup Example File Page Page Introduction Using the Optional Setup ModuleSetup Module Installation ←Copy to Printer ←Copy to Module Initializing Setup ModuleNew Setup Module Detected Copying Setup To Module Copying Setup to Printer I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code and Escape Sequence Summaries Ansi x3.64 Emulation Epson FX Emulation 100 IBM Proprinter Emulation ESC \ n1 n2 Print Characters ESC n Print Single Character ESC @ n1 n2 m1 m2 m3 m4 Double-High ModeDelete ESC a Simple TTY Emulation Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page 111 Specifications60 to 240 dpi horizontally x 72 dpi vertically 112 Inches 113 23,000,000 character, mobius loop cartridge 114 PrinterWorkmanship 115 116 117 Glossary of Terms 118 Printer is powered on default value Able to respond to the commands and textOnline Refers to the state of the printer when Received from the host computer