Open the tractor doors and remove the old form | Printek 8000SE

D A I L Y O P E R A T I O N

FormsMaster 8003se with front and center

tractors tilted forward.

6. Open the tractor doors and remove the old form.

FormsMaster 8003se with rear path empty

7.If the new form is a different width than the previous form, unlock the right tractor and move it to approximately the new position. Note that the left tractor position is fixed and may not be moved.

29

Image 37

Printek 8000SE manual Open the tractor doors and remove the old form

Contents

FormsMaster 8000se Series Part Number Iii Specifications are subject to change without noticePage Page Table of Contents Introduction To Setup Common Error ConditionsError Messages Preventive Maintenance Obtaining Service Forms Menu Simple TTY Emulation 103 Printek Emulation 104 102Viii Models and Options Introduction Manual Contents Page Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing the Ribbon Cartridge T T I N G S T a R T E D Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsMaster 8000se Single Tractor Model Loading PaperOpen the doors on each tractor FormsMaster 8003se TriTrak Model Loading the Front Tractors Loading the Center Tractors Selecting Which Form to Print Printer Self-Test T T I N G S T a R T E D Introduction Daily Operation LCD Display and Online Indicator Control Panel FeaturesDisplay will show the currently selected I L Y O P E R a T I O N Control Panel Buttons Forms which have been previously configured This button is used to access up to ten differentConfiguration for more information Move forward for easy access to all tractors Adjustment is shown first. Pressing the Value When Align Print is pressed, the horizontalTo access the vertical adjustment, press either Form Selecting a Form Already Loaded in the Tractors Selecting and Loading FormsLoading a New or Different Form In the Tractors Loading the Form in the Tractors Open the tractor doors and remove the old form Paper positioned in left tractor New form loaded in tractors Ejecting And Tearing Off a Form Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Close the ribbon lid and place printer back on line Installing the New Ribbon Cartridge Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ ⎯0.30→ Down/Up Print Check Paper Common Error Conditions Too Much Paper to Unload No Paper to LoadSelected Form is Not Loaded No Ribbon or Wrong Ribbon Ribbon Lid Open Other ErrorsPaper Door Open Change Ribbon Introduction To Setup Printer ConfigurationSetup Buttons Entering Setup Menus Entering SetupUsing the Menu Button Using the Submenu Button Exiting Setup Using the Item and Value Buttons←No Exit Setup ←Yes Menus? Exiting Menus Saving Changes No Changes Forms Menu Form Name Form Forms Menu ItemsTractor Path Front Automatic Cut No Cut AdjustmentLines/Inch Form Length 66 Lines Possible Values 0* … 226 Lines Top Margin 0 LinesBottom Margin 0 Lines Left Margin Column Possible Values Column 0* …Possible Values Column 4 … Right Margin Column Draft Speed Normal Font Epson FX FDImpact Force Normal Language Zero Normal Possible Values Normal*, SlashedPossible Values No*, Yes Unidirectional No Entering the Interface Menu Interface MenuSerial Emulation Epson RS-232C Serial Interface ItemsAuto CR On Auto LF Off Minimum Buffer No Characters ControlBaud Rate Data Bits Stop Bits DTR Power On/OffParity None Busy Polarity Low XON/XOFF Off Possible Values Power On/OffETX/ACK Off I N T E R C O N F I G U R a T I O N Parallel/LAN Interface Items LAN Setup OffParallel/LAN Possible Values On, Off Subnet Mask IP AddressIP Gateway Auto LF Off Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Possible Values Finish Paper Out Fault Finish Char. To Ignore 255 Possible Values 0, … Top Oversized Off Top of Barcode OffUser Language English Size 8192 Characters Truncate Lines No Possible Values Yes, NoPossible Values On*, Off Ribbon Check On ImagerPlus Graphic Card Ribbon Life Million CharsImagerPlus Emulation QMS CodeV Line Terminator ControlCharact 5E HexBar Code Density High-Res QMS Char Set Ignore Data Not Active Free Format Not ActiveImager Zero Slashed Vertical DPI LineRegistrati Not MaintainedVertical Text Version CodeV SP Fields Process This item selects the Spacing mode Quiet Mode Not ActiveTest Menu Delete Logos No Print Menus Test Mode Off I N T E R C O N F I G U R a T I O N Page Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenanceError Message Page Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed V a N C E D S E T U P F E a T U R E S Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Page Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Page Remote Setup Example File Page Page Setup Module Installation Using the Optional Setup ModuleIntroduction New Setup Module Detected Initializing Setup Module←Copy to Printer ←Copy to Module Copying Setup To Module Copying Setup to Printer I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code and Escape Sequence Summaries Ansi x3.64 Emulation Epson FX Emulation 100 IBM Proprinter Emulation ESC \ n1 n2 Print Characters ESC n Print Single Character ESC @ n1 n2 m1 m2 m3 m4 Double-High ModeDelete ESC a Simple TTY Emulation Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page 60 to 240 dpi horizontally x 72 dpi vertically Specifications111 112 Inches 113 23,000,000 character, mobius loop cartridge Workmanship Printer114 115 116 117 Glossary of Terms 118 Printer is powered on default value Able to respond to the commands and textOnline Refers to the state of the printer when Received from the host computer