Printer Reset Conditions | Printek 8000SE specs

PRINTER RESET CONDITIONS

The following list describes conditions that are assumed whenever power is applied to the printer, changes have been made in SETUP, or a reset escape sequence is received (when the printer is operating in an emulation mode that supports such a sequence).

This list includes all variables that you can modify for all emulations, even though some emulations cannot modify all of the variables shown. Refer to the appropriate section of this manual for the emulation you are using.

Variable		Reset Condition
character pitch		according to current form setup
left margin		according to current form setup
right margin		according to current form setup
line pitch		according to current form setup
form length		according to current form setup
top margin		according to current form setup
bottom margin		according to current form setup
font		according to current form setup
impact mode		according to current form setup
language		according to current form setup
normal/slashed zero		according to current form setup
auto cut mode		according to current form setup
unidirectional mode		according to current form setup
top of form		set to current position
text in an incomplete line		discarded
input buffer		cleared (unless reset from host)
control of data bit 8		accepted as received
control character symbols		according to interface setup
italics		off
double high		off
double strike		off
double wide		off
emphasized		off
superscript/subscript		off
underline		off

95

Image 103

Printek 8000SE manual Printer Reset Conditions

Contents

FormsMaster 8000se Series Part Number Iii Specifications are subject to change without noticePage Page Table of Contents Forms Menu Common Error ConditionsIntroduction To Setup Error Messages Preventive Maintenance Obtaining Service Simple TTY Emulation 103 Printek Emulation 104 102Viii Models and Options Introduction Manual Contents Page Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing the Ribbon Cartridge T T I N G S T a R T E D Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer FormsMaster 8000se Single Tractor Model Loading PaperOpen the doors on each tractor FormsMaster 8003se TriTrak Model Loading the Front Tractors Loading the Center Tractors Selecting Which Form to Print Printer Self-Test T T I N G S T a R T E D Introduction Daily Operation LCD Display and Online Indicator Control Panel FeaturesDisplay will show the currently selected I L Y O P E R a T I O N Control Panel Buttons Move forward for easy access to all tractors This button is used to access up to ten differentForms which have been previously configured Configuration for more information Form When Align Print is pressed, the horizontalAdjustment is shown first. Pressing the Value To access the vertical adjustment, press either Selecting a Form Already Loaded in the Tractors Selecting and Loading FormsLoading a New or Different Form In the Tractors Loading the Form in the Tractors Open the tractor doors and remove the old form Paper positioned in left tractor New form loaded in tractors Ejecting And Tearing Off a Form Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Close the ribbon lid and place printer back on line Installing the New Ribbon Cartridge ←0.00→ Aligning PrintAligning Print On Invoices Left/Right ⎯0.30→ Down/Up Print Check Paper Common Error Conditions No Ribbon or Wrong Ribbon No Paper to LoadToo Much Paper to Unload Selected Form is Not Loaded Change Ribbon Other ErrorsRibbon Lid Open Paper Door Open Introduction To Setup Printer ConfigurationSetup Buttons Using the Submenu Button Entering SetupEntering Setup Menus Using the Menu Button Exiting Menus Saving Changes No Changes Using the Item and Value ButtonsExiting Setup ←No Exit Setup ←Yes Menus? Forms Menu Form Name Form Forms Menu ItemsTractor Path Front Form Length 66 Lines Cut AdjustmentAutomatic Cut No Lines/Inch Possible Values 0* … 226 Lines Top Margin 0 LinesBottom Margin 0 Lines Right Margin Column Possible Values Column 0* …Left Margin Column Possible Values Column 4 … Language Font Epson FX FDDraft Speed Normal Impact Force Normal Unidirectional No Possible Values Normal*, SlashedZero Normal Possible Values No*, Yes Entering the Interface Menu Interface MenuSerial Auto LF Off RS-232C Serial Interface ItemsEmulation Epson Auto CR On Data Bits Characters ControlMinimum Buffer No Baud Rate Busy Polarity Low DTR Power On/OffStop Bits Parity None XON/XOFF Off Possible Values Power On/OffETX/ACK Off I N T E R C O N F I G U R a T I O N Possible Values On, Off LAN Setup OffParallel/LAN Interface Items Parallel/LAN Subnet Mask IP AddressIP Gateway Auto LF Off Options Menu Auto-Scroll 1 Second DelayMax Form Allowed Possible Values Finish Paper Out Fault Finish Char. To Ignore 255 Possible Values 0, … Size 8192 Characters Top of Barcode OffTop Oversized Off User Language English Ribbon Check On Possible Values Yes, NoTruncate Lines No Possible Values On*, Off Emulation QMS CodeV Ribbon Life Million CharsImagerPlus Graphic Card ImagerPlus QMS Char Set ControlCharact 5E HexLine Terminator Bar Code Density High-Res Ignore Data Not Active Free Format Not ActiveImager Zero Slashed CodeV SP Fields Process LineRegistrati Not MaintainedVertical DPI Vertical Text Version Delete Logos No Quiet Mode Not ActiveThis item selects the Spacing mode Test Menu Print Menus Test Mode Off I N T E R C O N F I G U R a T I O N Page Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Obtaining Service Preventive MaintenanceError Message Page Page Security Menu Advanced Setup FeaturesAlign Print Edit Allowed V a N C E D S E T U P F E a T U R E S Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Page Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Page Remote Setup Example File Page Page Setup Module Installation Using the Optional Setup ModuleIntroduction New Setup Module Detected Initializing Setup Module←Copy to Printer ←Copy to Module Copying Setup To Module Copying Setup to Printer I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code and Escape Sequence Summaries Ansi x3.64 Emulation Epson FX Emulation 100 IBM Proprinter Emulation ESC a ESC @ n1 n2 m1 m2 m3 m4 Double-High ModeESC \ n1 n2 Print Characters ESC n Print Single Character Delete Simple TTY Emulation Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page 60 to 240 dpi horizontally x 72 dpi vertically Specifications111 112 Inches 113 23,000,000 character, mobius loop cartridge Workmanship Printer114 115 116 117 Glossary of Terms 118 Received from the host computer Able to respond to the commands and textPrinter is powered on default value Online Refers to the state of the printer when