New form loaded in tractors | Printek 8000SE guide

D A I L Y O P E R A T I O N

New form loaded in tractors

Informing the Printer That the New Form is Loaded

11.Press the LOAD button. The display will now show that the new form has been “loaded”.

12.If your printer is a FormsMaster 8003se you may repeat the above steps to load additional forms at this time.

13.Close the paper door.

14.Make sure the correct form to be positioned for printing is selected and press either the LOAD button or the ONLINE button. The LOAD button will position the form for printing but will not place the printer on line. The ONLINE button will both position the form and place the printer on line. Note that the first time the printer is placed on line after a new form is loaded, the form(s) currently known to be loaded by the printer will scroll across the display as the printer goes on line. The operator should observe the forms displayed to confirm that the correct forms are recognized as loaded.

31

Image 39

Printek 8000SE manual New form loaded in tractors

Contents

FormsMaster 8000se Series Part Number Iii Specifications are subject to change without noticePage Page Table of Contents Forms Menu Common Error ConditionsIntroduction To Setup Error Messages Preventive Maintenance Obtaining Service 102 Simple TTY Emulation 103 Printek Emulation 104Viii Models and Options Introduction Manual Contents Page Page Getting Started Installation Interface Set Up RS-232C Serial Interface Pin Signal Parallel Interface Ethernet 10/100BaseT Wireless Ethernet Print Server Why Use Only Printek Brand Ribbons Installing the Ribbon Cartridge T T I N G S T a R T E D Ribbon Installation Installing the Ribbon Cartridge Close the ribbon lid on top of the printer Loading Paper FormsMaster 8000se Single Tractor ModelOpen the doors on each tractor FormsMaster 8003se TriTrak Model Loading the Front Tractors Loading the Center Tractors Selecting Which Form to Print Printer Self-Test T T I N G S T a R T E D Introduction Daily Operation Control Panel Features LCD Display and Online IndicatorDisplay will show the currently selected I L Y O P E R a T I O N Control Panel Buttons Move forward for easy access to all tractors This button is used to access up to ten differentForms which have been previously configured Configuration for more information Form When Align Print is pressed, the horizontalAdjustment is shown first. Pressing the Value To access the vertical adjustment, press either Selecting and Loading Forms Selecting a Form Already Loaded in the TractorsLoading a New or Different Form In the Tractors Loading the Form in the Tractors Open the tractor doors and remove the old form Paper positioned in left tractor New form loaded in tractors Ejecting And Tearing Off a Form Tearing off a form Removing the Old Ribbon Cartridge Installing a New Ribbon Cartridge Close the ribbon lid and place printer back on line Installing the New Ribbon Cartridge ←0.00→ Aligning PrintAligning Print On Invoices Left/Right ⎯0.30→ Down/Up Print Check Paper Common Error Conditions No Ribbon or Wrong Ribbon No Paper to LoadToo Much Paper to Unload Selected Form is Not Loaded Change Ribbon Other ErrorsRibbon Lid Open Paper Door Open Printer Configuration Introduction To SetupSetup Buttons Using the Submenu Button Entering SetupEntering Setup Menus Using the Menu Button Exiting Menus Saving Changes No Changes Using the Item and Value ButtonsExiting Setup ←No Exit Setup ←Yes Menus? Forms Menu Forms Menu Items Form Name FormTractor Path Front Form Length 66 Lines Cut AdjustmentAutomatic Cut No Lines/Inch Top Margin 0 Lines Possible Values 0* … 226 LinesBottom Margin 0 Lines Right Margin Column Possible Values Column 0* …Left Margin Column Possible Values Column 4 … Language Font Epson FX FDDraft Speed Normal Impact Force Normal Unidirectional No Possible Values Normal*, SlashedZero Normal Possible Values No*, Yes Interface Menu Entering the Interface MenuSerial Auto LF Off RS-232C Serial Interface ItemsEmulation Epson Auto CR On Data Bits Characters ControlMinimum Buffer No Baud Rate Busy Polarity Low DTR Power On/OffStop Bits Parity None Possible Values Power On/Off XON/XOFF OffETX/ACK Off I N T E R C O N F I G U R a T I O N Possible Values On, Off LAN Setup OffParallel/LAN Interface Items Parallel/LAN IP Address Subnet MaskIP Gateway Auto LF Off Auto-Scroll 1 Second Delay Options MenuMax Form Allowed Possible Values Finish Paper Out Fault Finish Char. To Ignore 255 Possible Values 0, … Size 8192 Characters Top of Barcode OffTop Oversized Off User Language English Ribbon Check On Possible Values Yes, NoTruncate Lines No Possible Values On*, Off Emulation QMS CodeV Ribbon Life Million CharsImagerPlus Graphic Card ImagerPlus QMS Char Set ControlCharact 5E HexLine Terminator Bar Code Density High-Res Free Format Not Active Ignore Data Not ActiveImager Zero Slashed CodeV SP Fields Process LineRegistrati Not MaintainedVertical DPI Vertical Text Version Delete Logos No Quiet Mode Not ActiveThis item selects the Spacing mode Test Menu Print Menus Test Mode Off I N T E R C O N F I G U R a T I O N Page Form Construction Form Construction Form Layout Considerations Error Messages Maintenance Troubleshooting Preventive Maintenance Obtaining ServiceError Message Page Page Advanced Setup Features Security MenuAlign Print Edit Allowed V a N C E D S E T U P F E a T U R E S Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Page Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Page Remote Setup Example File Page Page Using the Optional Setup Module Setup Module InstallationIntroduction Initializing Setup Module New Setup Module Detected←Copy to Printer ←Copy to Module Copying Setup To Module Copying Setup to Printer I N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Horizontal tabs Genicom 3840 and 3410 Emulation Control Code and Escape Sequence Summaries Ansi x3.64 Emulation Epson FX Emulation 100 IBM Proprinter Emulation ESC a ESC @ n1 n2 m1 m2 m3 m4 Double-High ModeESC \ n1 n2 Print Characters ESC n Print Single Character Delete Simple TTY Emulation Printek Emulation 105 Ascii Character Tables 106 107 108 109 Page Specifications 60 to 240 dpi horizontally x 72 dpi vertically111 112 Inches 113 23,000,000 character, mobius loop cartridge Printer Workmanship114 115 116 117 Glossary of Terms 118 Received from the host computer Able to respond to the commands and textPrinter is powered on default value Online Refers to the state of the printer when