Electrical & RF Specification | Quatech IN5000, DP500, HD500

Quatech, Inc.	AirborneDirect™ User Manual

7.0Electrical & RF Specification

Table 8- Absolute Maximum Values1

	Parameter			Min			Max			Unit
	Parameter			Min			Max			Unit

	Maximum Supply Voltage - Enterprise		4.5			5.5				VDC

	Maximum Supply Voltage - Industrial			5.0			36			VDC

	Power Dissipation						3.00			W

	Operating Temperature Range			-40			85			oC
	Storage Temperature			-50			125			oC

Note: 1. Values are absolute ratings, exceeding these values may cause permanent damage to the device.

Table 9 - RF Characteristics – 802.11b/g

	Symbol	Parameter	Rate (Mb/s)	Min	Average		Peak	Units
	Symbol	Parameter	Rate (Mb/s)	Min	dBm / mW		dBm / mW	Units
					dBm / mW		dBm / mW
	POUTB	Transmit Power	11, 5.5, 2, 1	13.0	15.0	31.6		dBm
	POUTB	Output 802.11b	11, 5.5, 2, 1	13.0	15.0	31.6		dBm
		Output 802.11b
	POUTG	Transmit Power	6, 9, 12, 18, 24,	13.0	15.0	31.6		dBm
	POUTG	Output 802.11g	36, 48, 54	13.0	15.0	31.6		dBm
		Output 802.11g	36, 48, 54
		Receive	11			-89
	PRSENB	Sensitivity	1			-93		dBm
		802.11b	1			-93
			54			-72
		Receive	36			-79
	PRSENG	Sensitivity	18			-85		dBm
		802.11g	18			-85
			6			-90

				Frequency
	FRANGEBG			Frequency			2412	2484	MHz
	FRANGEBG			Range			2412	2484	MHz

The transmit power is automatically controlled by the device for minimum power

consumption.

The transmit power at the antenna connector is 15dBm±2dBm.

24

2/21/2011

100-8510-110

Image 24

Quatech IN5000, DP500, HD500 Electrical & RF Specification, Absolute Maximum Values1, RF Characteristics 802.11b/g

Contents

Revision February Intentionally Left Blank Quatech Confidential Quatech, Inc. Headquarters Intentionally Left Blank Contents 100 Figures Modular Approval Grant Numbers Conventions TerminologyFile Format Product Description Features Device Types SerialEthernet Serial + Ethernet Enterprise Class Industrial Class Heavy Duty Class Industrial AirborneDirect Device AirborneDirect Users Guide Block Diagram ABDG-SE/ET-DP5XX Block Diagram ABDG-ET/SE-IN5XXX Block Diagram Pin out and Connectors Power on pinSerial Ports RS232 DTE Ethernet Port Serial Ports by Product Class Connector Definition OEM Reset Switch Factory ResetConnector Description Enterprise Serial Interface Jumpers Interface Selection Jumpers Indicator LED’s Industrial LED Indicators Electrical & RF Specification RF Characteristics 802.11b/gSymbol Parameter Rate Mb/s Min Absolute Maximum Values1 Band Supported Data Rates Mb/s Band Region Freq Range No. Channels GHz AC Electrical Characteristics Transmitter Performance/RangeRadio Typical Performance Range Data Rate Typical Outdoor Distance Antenna Antenna SelectionHost Board Mounted Antenna Antenna Type Features Cost Size Availability Performance Host Chassis Mounted AntennaEmbedded Antenna Embedded Antenna Options Antenna Location Performance AirborneDirect Users Guide Mechanical Outline Enterprise Class RP-SMA Reverse Polarity SMADB-9M Male RJ-45 Plug Antenna Connector RP-SMA Reverse Polarity SMA Serial Connector DB-9M MalePower Connector Terminal Block 2 connector Mechanical Outline Industrial Class Attach Antenna and Power-up the AirborneDirect Getting StartedUnpack the AirborneDirect Device Connect AirborneDirect to host Configuring Device Industrial Serial ABDG-SE-IN5XXX SE-IN5XXX Accessing the Web Interface Opening web page shows adapter status No TCP Connection Configuring Device Enterprise Serial ABDG-SE-DP5XX CLI Command DescriptionConnect a Host Computer Interacting with the AirborneDirect device Determine and Store the Access Point Ssid Determine the Device’s IP addressUart Determine Modules IP Address Accessing the Device Using the Web Interface Accessing the Device Using Telnet Configuring Device Enterprise/Industrial Ethernet ET-DP5XX/IN5XXX Accessing the Web Interface Opening web page shows adapter status ABDG-ET-DP5XX Using the Web Interface Website Login Username dpac Password dpac Navigation Bar Title Description Feature Links Navigating the Website Updating a Field Airborne Web Upload Configuration Files Uploading CertificatesUploading Certificates Uploading Configurations Firmware Update Updating Firmware Select Maintenance Select Update Module FirmwareUpdating Firmware Step Description Press Load New Firmware Express Setup Configuration Express Page SetupSelect Express Setup Select Radio Startup Mode Select Ethernet Static IP Configuring the Wireless Interface Configuring for Infrastructure NetworksConfiguring for AdHoc Networks Configuring Wireless Interface Infrastructure Configuring Wireless Interface AdHoc Select Wireless LAN ChannelSelect Network Settings Configuring the Security Settings Configuring for WEP SecurityConfiguring for WEP Security Configuring for WPA-PSK Security Configuring for WPA SecuritySelect WPA Protocol Version Select WPA/WPA2 Pre Shared Key PSK Configuring for WPA2-PSK Security Configuring for WPA2 Security Configuring for Peap Security Configuring for Peap Security Select CA Certificate Filename Configuring Network Settings Configuring Dhcp on Wlan InterfaceConfiguring Dhcp Wlan Select Wlan Dhcp Configuring Dhcp on Ethernet Interface Configuring Dhcp Ethernet Configuring a Static IP Address on Wlan Interface Configuring Static IP WlanSelect Wlan Static IP Address Select Subnet Mask Configuring a Static IP Address on Ethernet Interface Configuring Static IP EthernetStep Select Ethernet Static IP Address XXX.XXX.XXX.XXX Configuring Serial Device Server Configuring Serial Port for Access on Telnet PortConfigure Data Tunnel on Telnet Port Configuring Serial Port 1 for Access on Tunnel Port Select Serial Port 1 Settings/Serial PortSettings Select Serial CLI Default Mode Configure Data Tunnel on Serial Port 1 Tunnel Port TCP Data Tunnel using Tunnel Port on Serial Port Configuring Serial Port 2 for Access on Tunnel Port Configure Data Tunnel on Serial Port 2 Tunnel Port TCP Configuring Serial Port 1 as TCP Client Configure Serial Port 1 as TCP Client Configuring Serial Port 2 as TCP Client Configure Serial Port 2 as TCP Client Serial Port Installing and Using the Airborne VirtualCOM Driver Install Vcom Select Properties AirborneDirect Users Guide Cable Replacement Slave Configuration Replacing a Serial Cable Cable Replacement Master Configuration Select Outbound Transmit Type Configuring Ethernet Adapter Ethernet Bridge Functionality Public Network Interface Ethernet Adapter interface Configuration Dhcp Select Dhcp Server EnabledPrivate Network Interface Ethernet Adapter interface Configuration Static IP Ethernet Gateway IP Address. Access toSelect Ethernet Gateway IP Address Select Disable from drop down menu Not be the same Web Page Overview Module Status URL Ethernet Status Ethernet Dhcp Clients Radio Statistics Ethernet Statistics Express Setup Field CLI Command Wlan Subnet Mask Wlan Settings Wlan Security Settings EAP Identity Network Settings Wlan Gateway IP Address Serial Port Settings Serial Port 2 Settings Connection Settings 21/2011 103 Ethernet Settings Wireless Routing Settings Ethernet Routing Settings Advanced Settings 108 21/2011 100-8510-110 21/2011 109 Upload Configuration File List Configuration File Delete Configuration File Active Configuration User Configuration OEM Configuration Factory Configuration WPA Configuration List Certificates Upload Certificate Delete Certificate Network Home Discover Airborne Modules Scan for Access Points Maintenance Home Update Module Firmware Reset Factory Defaults Restart Module Maintenance/Blink the Post LED Blink the Post LED Maintenance/Stop Blinking the Post LED Stop Blinking the Post LED Change Module Personality Certification & Regulatory Approvals FCC StatementFCC RF Exposure Statement Regulatory Approvals Information for Canadian Users IC Notice 25.4 FCC/IC Modular ApprovalModular Approval Grant Numbers Country Standard Regulatory Test Mode Support Physical & Environmental Approvals Mechanical ApprovalsTest Reference Conditions Change Log Date Section Change Description Author