Configuring Device Industrial Serial ABDG-SE-IN5XXX | Quatech HD500

AirborneDirect™ Users Guide	Quatech, Inc.

12.0 Configuring Device – Industrial Serial (ABDG-SE-IN5XXX)

The following describes initial connection to an AirborneDirect™ Serial Device Server (ABDG-SE-IN5XXX). If you have an Ethernet device (ABGD-ET-DP5XX/IN5010), please go to section 14.0. If you have purchased a SE-DP5XX device please go to section 13.0 for the set-up instructions.

The instructions in Table 14 provide step-by-step instructions for configuration of the ABDG-SE-IN5XXX product family.

Table 14 - SE-IN5XXX Accessing the Web Interface

1

2

3

4

5

Open the AirborneDirect™ packaging and locate the Install CD.

Place the CD in the CD/DVD drive of the laptop or desktop you will be using to configure the AirborneDirect™ device. Follow the on screen directions for installation of the appropriate device software and documentation.

Connect the Ethernet cable on ABDG to an Ethernet port on the laptop or desktop system.

Apply power to the ABDG-SE-IN5XXX.

The unit will boot and display one of the following LED patterns:

ABDG-SE-IN5XXX
COMM:	 Off
LINK :	 Off
POST:	 Orange
POWER:	 Blue

Run the Airborne Management System application. This was installed during the CD installation and a menu item will be found in the Airborne folder located in the programs directory of your system.

When the application opens the following dialog will be displayed:

6

Select Group Name: manuf and enter Group Password: dpac

100-8510-110

2/21/2011

35

Image 35

Quatech HD500, IN5000, DP500 Configuring Device Industrial Serial ABDG-SE-IN5XXX, SE-IN5XXX Accessing the Web Interface

Contents

Revision February Intentionally Left Blank Quatech, Inc. Headquarters Quatech Confidential Intentionally Left Blank Contents 100 Figures Modular Approval Grant Numbers File Format ConventionsTerminology Product Description Features Serial + Ethernet Device TypesSerial Ethernet Industrial Class Enterprise Class Industrial AirborneDirect Device Heavy Duty Class AirborneDirect Users Guide ABDG-SE/ET-DP5XX Block Diagram Block Diagram ABDG-ET/SE-IN5XXX Block Diagram RS232 DTE Pin out and ConnectorsPower on pin Serial Ports Serial Ports by Product Class Ethernet Port Connector Description Connector DefinitionOEM Reset Switch Factory Reset Interface Selection Jumpers Enterprise Serial Interface Jumpers Indicator LED’s Industrial LED Indicators Absolute Maximum Values1 Electrical & RF SpecificationRF Characteristics 802.11b/g Symbol Parameter Rate Mb/s Min Band Region Freq Range No. Channels GHz Band Supported Data Rates Mb/s Data Rate Typical Outdoor Distance AC Electrical Characteristics TransmitterPerformance/Range Radio Typical Performance Range Host Board Mounted Antenna AntennaAntenna Selection Embedded Antenna Options Antenna Type Features Cost Size Availability PerformanceHost Chassis Mounted Antenna Embedded Antenna Antenna Location Performance AirborneDirect Users Guide RJ-45 Plug Mechanical Outline Enterprise ClassRP-SMA Reverse Polarity SMA DB-9M Male Mechanical Outline Industrial Class Antenna Connector RP-SMA Reverse Polarity SMASerial Connector DB-9M Male Power Connector Terminal Block 2 connector Connect AirborneDirect to host Attach Antenna and Power-up the AirborneDirectGetting Started Unpack the AirborneDirect Device SE-IN5XXX Accessing the Web Interface Configuring Device Industrial Serial ABDG-SE-IN5XXX Opening web page shows adapter status No TCP Connection Interacting with the AirborneDirect device Configuring Device Enterprise Serial ABDG-SE-DP5XXCLI Command Description Connect a Host Computer Uart Determine Modules IP Address Determine and Store the Access Point SsidDetermine the Device’s IP address Accessing the Device Using Telnet Accessing the Device Using the Web Interface ET-DP5XX/IN5XXX Accessing the Web Interface Configuring Device Enterprise/Industrial Ethernet Opening web page shows adapter status ABDG-ET-DP5XX Website Login Username dpac Password dpac Using the Web Interface Title Description Navigation Bar Navigating the Website Feature Links Airborne Web Updating a Field Uploading Certificates Upload Configuration FilesUploading Certificates Uploading Configurations Updating Firmware Firmware Update Updating Firmware Select MaintenanceSelect Update Module Firmware Press Load New Firmware Step Description Select Express Setup Express Setup ConfigurationExpress Page Setup Select Radio Startup Mode Select Ethernet Static IP Configuring Wireless Interface Infrastructure Configuring the Wireless InterfaceConfiguring for Infrastructure Networks Configuring for AdHoc Networks Select Network Settings Configuring Wireless Interface AdHocSelect Wireless LAN Channel Configuring for WEP Security Configuring the Security SettingsConfiguring for WEP Security Select WPA/WPA2 Pre Shared Key PSK Configuring for WPA-PSK SecurityConfiguring for WPA Security Select WPA Protocol Version Configuring for WPA2 Security Configuring for WPA2-PSK Security Configuring for Peap Security Configuring for Peap Security Select CA Certificate Filename Select Wlan Dhcp Configuring Network SettingsConfiguring Dhcp on Wlan Interface Configuring Dhcp Wlan Configuring Dhcp Ethernet Configuring Dhcp on Ethernet Interface Select Subnet Mask Configuring a Static IP Address on Wlan InterfaceConfiguring Static IP Wlan Select Wlan Static IP Address Select Ethernet Static IP Address Configuring a Static IP Address on Ethernet InterfaceConfiguring Static IP Ethernet Step XXX.XXX.XXX.XXX Configure Data Tunnel on Telnet Port Configuring Serial Device ServerConfiguring Serial Port for Access on Telnet Port Select Serial CLI Default Mode Configuring Serial Port 1 for Access on Tunnel PortSelect Serial Port 1 Settings/Serial Port Settings Data Tunnel using Tunnel Port on Serial Port Configure Data Tunnel on Serial Port 1 Tunnel Port TCP Configure Data Tunnel on Serial Port 2 Tunnel Port TCP Configuring Serial Port 2 for Access on Tunnel Port Configure Serial Port 1 as TCP Client Configuring Serial Port 1 as TCP Client Configure Serial Port 2 as TCP Client Configuring Serial Port 2 as TCP Client Serial Port Install Vcom Installing and Using the Airborne VirtualCOM Driver Select Properties AirborneDirect Users Guide Replacing a Serial Cable Cable Replacement Slave Configuration Cable Replacement Master Configuration Select Outbound Transmit Type Ethernet Bridge Functionality Configuring Ethernet Adapter Public Network Interface Private Network Interface Ethernet Adapter interface Configuration DhcpSelect Dhcp Server Enabled Select Ethernet Gateway IP Address Ethernet Adapter interface Configuration Static IPEthernet Gateway IP Address. Access to Select Disable from drop down menu Not be the same Web Page Overview URL Module Status Ethernet Status Ethernet Dhcp Clients Radio Statistics Ethernet Statistics Field CLI Command Express Setup Wlan Subnet Mask Wlan Settings Wlan Security Settings EAP Identity Network Settings Wlan Gateway IP Address Serial Port Settings Serial Port 2 Settings Connection Settings 21/2011 103 Ethernet Settings Wireless Routing Settings Ethernet Routing Settings Advanced Settings 108 21/2011 100-8510-110 21/2011 109 Upload Configuration File List Configuration File Delete Configuration File Active Configuration User Configuration OEM Configuration Factory Configuration WPA Configuration List Certificates Upload Certificate Delete Certificate Network Home Discover Airborne Modules Scan for Access Points Maintenance Home Update Module Firmware Reset Factory Defaults Restart Module Blink the Post LED Maintenance/Blink the Post LED Stop Blinking the Post LED Maintenance/Stop Blinking the Post LED Change Module Personality Regulatory Approvals Certification & Regulatory ApprovalsFCC Statement FCC RF Exposure Statement Country Standard Information for Canadian Users IC Notice25.4 FCC/IC Modular Approval Modular Approval Grant Numbers Regulatory Test Mode Support Test Reference Conditions Physical & Environmental ApprovalsMechanical Approvals Date Section Change Description Author Change Log