Manuals / SATO / Computer Equipment / Printer

SATO GT 424e, GT408, GT 410 manual Advanced Mode, Menu, Description, Direct

Models: GT 410 GT408 GT 424e

1 106

Download 106 pages 5.28 Kb

Page 54

ADVANCED MODE (4-3)

Unit 4: Operation

		ADVANCED MODE (4-3)

	MENU	DESCRIPTION

		Is the premiere screen of the Advanced Mode. The Advanced
		Mode is provided to make basic printer operational


		adjustments. Typically, once these adjustments or settings have
		been made, they will not require additional address unless a
		new job is downloaded. The following table identifies the menus

		of the Advanced Mode and their purpose.

		Allows the darkness (density) selection of the printed image.
		Has six selection options.
		Has six selection options.

DARKNESS RANGE

A B C D E F

				Determines whether the printer automatically detects the
				installation of optional peripherals such as a peeler or cutter. If

	PRINTER TYPE
	PRINTER TYPE			detected, the optional peripherial will be used without further
	AUTO SETTING
	YES	NO		configuration.
	YES	NO


				Allows the choice of continuous feed or tear-off operation. If the
				relative accessories have been correctly installed, their
				relative accessories have been correctly installed, their
	PRINTER TYPE			respective options will be displayed.
				respective options will be displayed.
	CONTINUOUS
	TEAR OFF
	DISPENSER
	CUTTER
	LINERLESS


				Allows the determination of wheather a backfeed motion will be
				applied. If so, the selection of before or after the printing of each

	BACKFEED MOTION
	BACKFEED MOTION			label.
				label.
	AFTER
	BEFOR
	NONE


				Allows the internal rewinder option to be turned activated or
				deactivated as applicable.

	REWINDER
	REWINDER
	ON	OFF



				Allows the printer to be switched to operate in the thermal
				transfer or direct thermal mode as desired.

	PRINT METHOD
	PRINT METHOD
	TRANSFER	DIRECT

SATO GT4xxe Series Operator Manual

PN 9001138A

Page 4-26

Image 54

SATO GT 424e, GT408, GT 410 manual Advanced Mode, Menu, Description, Direct

Contents

GT408/410/424e Printer OPERATOR MANUALTechnical Support Hotline 704 Technical Support Fax SATO America, Inc10350A Nations Ford Road Charlotte, NC Main Phone E-Mail satosales@satoamerica.com technical support@satoamerica.comINTRODUCTION TECHNICAL DATAINSTALLATION TABLE OF CONTENTSMAINTENANCE PRINTER CONFIGURATIONTROUBLESHOOTING Configuration ModesAbout This Manual General Description Control Features INTRODUCTIONABOUT THIS MANUAL WARNING PROVIDES INFORMATION THAT, IF UNHEEDED, MAYRESULT IN PRESONAL INJURY GENERAL DESCRIPTION Figure 1-1a, Primary ComponentsMaintenance Panel CONTROL FEATURESLED Indicators Power SwitchRibbon Sensing Interface Modules Character Font Capabilities TECHNICAL DATAPhysical Characteristics Power Enviromental Processing Print Media Barcode Capabilities Regulatory ApprovalsENVIRONMENTAL PHYSICAL CHARACTERISTICSPOWER PROCESSINGINTERFACE MODULES RIBBONSENSING MEDIAAUTO SMOOTHING FONTS CHARACTER FONT CAPABILITIESMATRIX FONTS VECTOR FONTCHARACTER CONTROL BAR CODE CAPABILTIESREGULATORY APPROVALS PN 9001138A Unit 2 Technical DataSATO GT4xxe Series Operator Manual PageINSTALLATION Unpacking Parts Identification Printer InstallationInterface Selection Accessories Installation UNPACKING & PARTS IDENTIFICATION PRINTER INSTALLATION SITE LOCATIONCABLE CONNECTION MEDIA SELECTION MEDIA & RIBBON LOADINGFigure 3-3a, Rolled Media & Ribbon Loading SATO GT4xxe Series Operator Manual Unit 3 InstallationFigure 3-3b, Fan-fold Media & Ribbon Loading PN 9001138ARS232C SPECIFICATIONS INTERFACE SELECTIONRS232C SERIAL INTERFACE DIRECTION RS232C SERIAL INTERFACE SIGNALSSIGNAL DEFINITION CABLE REQUIREMENTSIEEE1284 PARALLEL INTERFACE SPECIFICATIONSSIGNAL IEEE 1284 PARALLEL INTERFACE PIN ASSIGNMENTSUNIVERSAL SERIAL BUS USB ADAPTER 802.11B WIRELESS802.11B WIRELESS SPECIFICATIONS LOCAL AREA NETWORK LAN ETHERNETRECEIVE BUFFER ACK/NAK PROTOCOLACCESSORIES INSTALLATION EXTERNAL SIGNAL CONNECTORFigure 3-6, External Signal Connector MEMORY EXPANSION EXT Connector External Signal Interface INTERFACE UPGRADEWireless LAn 802.11b Interface Figure 3-8, Interface UpgradeLABEL CUTTER INSTALLATION LABEL PEELER INSTALLATIONConfiguration Modes Operational Adjustments PRINTER OPERATIONCONFIGURATION MODES NORMAL MODEUSER MODE Figure 4-2, User ModeADVANCED MODE Figure 4-3, Advanced ModeIEEE1284 INTERFACE SETUP MODE Figure 4-4, IEEE1284 Interface Setup ModeRS232C INTERFACE SETUP MODE Figure 4-5, RS232C Interface Setup ModeCENTRONICS INTERFACE SETUP MODE Figure 4-6, Centronics Interface ModeLAN INTERFACE SETUP MODE Figure 4-7, LAN Interface Setup ModeUSB INTERFACE SETUP MODE Figure 4-8, USB Interface Setup ModeCARTRIDGE MODE Figure 4-9, Cartridge ModeSEMBL MODE Figure 4-10, SEMBL ModeTEST PRINT MODE Figure 4-11, Test Print ModeDOWNLOAD MODE Figure 4-12, Download ModeHEX DUMP MODE Figure 4-13, Hex Dump ModeBOOT DOWNLOAD MODE Figure 4-14, Boot Download ModeDATA SAVE MODE Figure 4-15, Data Save ModeDEFAULT SETTINGS MODE Figure 4-16, Default Settings ModePRINT CANCEL MODE Figure 4-17, Print Cancel ModePRINT DARKNESS DEFAULT MODE Figure 4-18, Print Density Default ModeSERVICE MODE Figure 4-19, Service ModeFACTORY MODE Figure 4-20, Factory ModeDESCRIPTION NORMAL MODEMENU ONLINEDESCRIPTION NORMAL MODEMENU YES NODESCRIPTION USER MODEMENU ONLINEDESCRIPTION USER MODEMENU PRINT OFFSETDESCRIPTION ADVANCED MODEMENU DIRECTADVANCED MODE MENUDESCRIPTION DESCRIPTION ADVANCED MODEMENU SEMBL MODEINTERFACE MODES 4-4 THROUGH MENUDESCRIPTION INTERFACE MODES 4-4 THROUGH MENUDESCRIPTION DESCRIPTION INTERFACE MODES 4-4 THROUGHMENU 4800DESCRIPTION INTERFACE MODES 4-4 THROUGHMENU InfrastructureINTERFACE MODES 4-4 THROUGH MENUDESCRIPTION DESCRIPTION CARTRIDGE MODEMENU COMPLETEDSEMBL MODE MENUDESCRIPTION TEST PRINT MODE MENUDESCRIPTION DESCRIPTION DOWNLOAD MODEMENU DOWNLOADHEX DUMP MODE MENUDESCRIPTION BOOT DOWNLOAD MODE MENUDESCRIPTION DATA SAVE MODE MENUDESCRIPTION DEFAULT MODE PRINTER SETTING YES NO DEFAULT SETTINGS MODEDEFAULT MODE PRINTER SETTING ALT. PROTOCOL DEFAULT ALT. PROTOCOL YES NOMENU PRINT CANCEL MODEPRINT DENSITY DEFAULT MODE DESCRIPTIONSERVICE MODE DESCRIPTIONMENU MENU SERVICE MODECOMMAND DESCRIPTIONSERVICE MODE MENUDESCRIPTION SERVICE MODE MENUDESCRIPTION FACTORY MODE MENUDESCRIPTION DESCRIPTION FACTORY MODEMENU Displays values for the dispenser counterOPERATIONAL ADJUSTMENTS DESCRIPTION/PROCEDUREPOTENTIOMETER PRINT Figure 4-21, Sensor & Accessory PositioningLABEL DIRECTIONCONTINUOUS MODE Figure 4-22, Print Base Reference PositionLABEL PRINT DIRECTION TEAR-OFF MODEPN 9001138A Unit 4 OperationSATO GT4xxe Series Operator Manual PageTROUBLESHOOTING Error Signals Troubleshooting Table Interface TroubleshootingTest Print Troubleshooting Sensor Locations Buffer Overflow error ERROR SIGNALSError No LCD DisplayError No Unit 5 TroubleshootingERROR SIGNALS Clean the paper path to establish a smooth paper flowError No Unit 5 TroubleshootingERROR SIGNALS Memory Writing errorError No Unit 5 TroubleshootingERROR SIGNALS Item Number errorError No Unit 5 TroubleshootingERROR SIGNALS SATO GTxxe Series Operator ManualLIGHT PRINT IMAGES TROUBLESHOOTING TABLEIMAGE VOIDS UNEVEN PRINT DARKNESSPRINTER CREATES A BLANK LABEL LCD FIELD ILLUMINATED BUT WITHOUT WORDS OR NO DISPLAY AT ALLMEANDERING MEDIA INCORRECT LABEL POSITIONINGPARALLEL INTERFACE INTERFACE TROUBLESHOOTINGTROUBLESHOOTING STEP RS232 SERIAL INTERFACELAN EHTERNET INTERFACE UNIVERSAL SERIAL BUS USB INTERFACETROUBLESHOOTING STEP TEST PRINT TROUBLESHOOTING Figure 5-1, Hex Dump ModeHEX DUMP MODE TEST LABEL PRINTING Figure 5-2, Test Print ModeFigure 5-3, Sample Test Label SAMPLE TEST LABELLABEL SENSOR LOCATIONSFigure 5-4, Sensor Locations PRINTMAINTENANCE Cleaning Procedures Replacement Procedures Adjustment ProceduresALLOW TO COOL TO ROOM TEMPERATURE PRIOR TO CLEANING CLEANING PROCEDURESWARNING DISCONNECT POWER SUPPLY TO THE PRINTER AND WARNING EXERSIZE CARE WHEN CLEANING TO PREVENTREPLACEMENT PROCEDURES PRINT HEAD REPLACEMENTFigure 6-1a, Print Head Replacement PLATEN ROLLER REPLACEMENT Figure 6-1b, Print Head ReplacementSATO GT4xxe Series Operator Manual Figure 6-2, Platen Roller ReplacementUnit 6 Maintenance PN 9001138AADJUSTMENT PROCEDURES PRINT HEAD ALIGNMENTFigure 6-3, Print Head Alignment Figure 6-4, Print Head Pressure Adjustment PRINT HEAD PRESSURE ADJUSTMENTPRESSURE ADJUSTMENT SCALEPRINT HEAD BALANCE ADJUSTMENT BALANCE ADJUSTMENTFigure 6-5, Print Head Balance Adjustment RIBBON GUIDE ADJUSTMENT Figure 6-6, Ribbon Guide AdjustmentLABEL SENSOR POSITIONING Figure 6-7, Label Sensor PositioningPOTENTIOMETER ADJUSTMENTS DESCRIPTION/PROCEDUREPOTENTIOMETER PN 9001138A Unit 6 MaintenanceSATO GT4xxe Series Operator Manual Page