Master with Word Swap | Schneider Electric LXM32M manual

LXM32M	5 Commissioning

5.6Master with Word Swap

The IP address of a master with Word Swap is set by means of the parameters EthMbIPswap1 ... EthMbIPswap4.

You may not set an IP for a master without Word Swap.

▶Check whether or not the master uses Word Swap.

▶If the master uses Word Swap, set the IP address of the master with the parameters EthMbIPswap1 ... EthMbIPswap4.

Parameter name	Description	Unit	Data type	Parameter address
HMI menu		Minimum value	R/W	via fieldbus
HMI name		Factory setting	Persistent
		Maximum value	Expert

EthMbIPswap1	IP address of master for Modbus word	-	UINT16	CANopen 3044:50h
	swap, byte 1	0	UINT16	Modbus 17568
	IP address of a Modbus master device. For	0	UINT16	Profibus 17568
	IP address of a Modbus master device. For	255	UINT16	CIP 168.1.80
	this master, the word order is swapped to		R/W
	"Low word first", instead of the default "High		R/W
	"Low word first", instead of the default "High		per.
	word first".		per.
	word first".		-
			-
	High word first -> Modicon Quantum
	Low word first -> Premium, HMI (Schneider
	Electric)
	Changed settings become active immedi-
	ately.

EthMbIPswap2	IP address of master for Modbus word	-	UINT16	CANopen 3044:51h
	swap, byte 2	0	UINT16	Modbus 17570
	Changed settings become active immedi-	0	UINT16	Profibus 17570
	Changed settings become active immedi-	255	UINT16	CIP 168.1.81
	ately.	255	UINT16	CIP 168.1.81
	ately.		R/W
			R/W
			per.
			-

EthMbIPswap3	IP address of master for Modbus word	-	UINT16	CANopen 3044:52h
	swap, byte 3	0	UINT16	Modbus 17572
	Changed settings become active immedi-	0	UINT16	Profibus 17572
	Changed settings become active immedi-	255	UINT16	CIP 168.1.82
	ately.	255	UINT16	CIP 168.1.82
	ately.		R/W
			R/W
			per.
			-

EthMbIPswap4	IP address of master for Modbus word	-	UINT16	CANopen 3044:53h
	swap, byte 4	0	UINT16	Modbus 17574
	Changed settings become active immedi-	0	UINT16	Profibus 17574
	Changed settings become active immedi-	255	UINT16	CIP 168.1.83
	ately.	255	UINT16	CIP 168.1.83
	ately.		R/W
			R/W
			per.
			-

0198441113843, V1.01, 01.2012

Modbus-TCP module

45

Image 45

Schneider Electric LXM32M manual Master with Word Swap

Contents

LXM32M Important information Table of contents Diagnostics and troubleshooting Accessories and spare parts LXM32M About this manual Further reading Fieldbus products on the network Introduction LXM32M Before you begin safety information Qualification of personnelIntended use Hazard categories Basic information Standards and terminology Modbus TCP technology BasicsFunction principle Bus topology Client / server model Network service Snmp Structure of a Modbus message Modbus TCP protocol Field Length Description Mbap header Connection management Modbus TCP communication Excep Name Description Tion Code Modbus response to a Modbus request Address Value Reading and writing parameters 4 I/O scanning to Drive Profile Lexium Byte Meaning Data type Parameter address 4.1 I/O scanning Output Bit Meaning 4.2 I/O scanning Input Inputs Bit Signal Factory setting Parameter channel Ctrl Subindex Index Modbus services Function Code Function Code 3 Read Multiple RegistersField Bytes Value Meaning Sub-function Code Diagnostics function Function Code 8 Diagnostics Function Code 16 Write Multiple Registers Function Code 23 ReadWrite Multiple Registers Object ID Object name Value Function Code 43 Encapsulated Interface Transport Example of Function Code Examples LXM32M Installation Installation of the moduleDescription Order no Pin Signal Meaning Electrical installation Commissioning the device Commissioning Switching on the device Power stage supply is switched off First Setup Manual assignment of the network address Bootp / boot BootpManual / MAnu Manual Dhcp / dhcP Dhcp IP address Ethernet module, byte Assignment of the network address via Bootp Assignment of the network address via Dhcp Setting the protocol Setting the transmission rate Set the IP address of the gateway with the parameters Setting the gateway Master with Word Swap Setting I/O-Scanning Setting the master for I/O scanningActivating I/O scanning Setting the mapping for I/O scanning PLC Setting communication monitoring for I/O scanning Setting the web server 0198441113843, V1.01 Operation Operating states Indication of the operating stateBit Name Meaning Bit Name Meaning Operating state Changing the operating state Indicating and monitoring the operating mode Operating modesBit Name Description Bit Name Description Starting and changing an operating mode MODE+ACTION Overview of operating modes Operating mode Jog Operating mode Electronic Gear 24 h Operating mode Profile Torque 23 h Operating mode Profile Velocity Operating mode Profile Position Operating mode Homing LXM32M6 Operation Operating mode Motion Sequence Web server Extended settings User interface Main menu Submenu Content FTP server Accessing the FTP server FDR service Fast Device Replacement LXM32M Fieldbus communication error diagnostics Diagnostics and troubleshooting Color Status Meaning Status LEDs Meaning for EtherNet/IP Meaning for Modbus TCP Color Error indication Excep Name Description Tion Code LXM32M Cables Accessories and spare parts LXM32M Units and conversion tables Glossary Rotation TemperatureTorque Moment of inertia Terms and Abbreviations LXM32M Index LXM32M