Setting the web server | Schneider Electric LXM32M guide

LXM32M	5 Commissioning

5.7.4Setting communication monitoring for I/O scanning

WARNING

LOSS OF CONTROL

The product is unable to detect an interruption of the network link if connection monitoring is not active.

•Verify that connection monitoring is on.

•The shorter the time for monitoring, the faster the detection of the interruption.

Failure to follow these instructions can result in death, serious injury or equipment damage.

Communication monitoring for I/O scanning is set by means of the parameter EthMbScanTimeout.

▶Set communication monitoring for I/O scanning with the parameter

EthMbScanTimeout.

Parameter name	Description	Unit	Data type	Parameter address
HMI menu		Minimum value	R/W	via fieldbus
HMI name		Factory setting	Persistent
		Maximum value	Expert

EthMbScanTimeou	Modbus TCP I/O scanning timeout	s	UINT16	CANopen 3044:2Dh
t	Communication monitoring timeout for Mod-	0.0	UINT16	Modbus 17498
	bus TCP.	2.0	UINT16	Profibus 17498
	bus TCP.	60.0	UINT16	CIP 168.1.45
	Value 0: Timeout monitoring disabled	60.0	UINT16	CIP 168.1.45
	Value 0: Timeout monitoring disabled		R/W
			R/W
	In increments of 0.1 s.		per.
	Changed settings become active immedi-		-
	Changed settings become active immedi-
	ately.

5.8Setting the web server

The web server is activated or deactivated by means of the parameter

EthWebserver.

▶If you do not want to use the web server, set the parameter

EthWebserver to "Off".

See chapter "6.3.1 Web server" for additional information on the web server.

	Parameter name	Description	Unit	Data type	Parameter address
	HMI menu		Minimum value	R/W	via fieldbus
	HMI name		Factory setting	Persistent
			Maximum value	Expert

01.2012	EthWebserver	Ethernet webserver	-	UINT16	CANopen 3044:6h
		1 / On: Ethernet webserver on	0	UINT16	Modbus 17420
		1 / On: Ethernet webserver on	1	UINT16	CIP 168.1.6
		0 / Off: Ethernet webserver off	1	UINT16	Profibus 17420
			1	UINT16	Profibus 17420
V1.01,		Changed settings become active the next		R/W
V1.01,		time the product is switched on.		per.
		time the product is switched on.		per.
0198441113843,				-

Modbus-TCP module

49

Image 49

Schneider Electric LXM32M manual Setting the web server, Setting communication monitoring for I/O scanning

Contents

LXM32M Important information Table of contents Diagnostics and troubleshooting Accessories and spare parts LXM32M About this manual Further reading Fieldbus products on the network Introduction LXM32M Qualification of personnel Before you begin safety informationIntended use Hazard categories Basic information Standards and terminology Modbus TCP technology BasicsFunction principle Bus topology Client / server model Network service Snmp Structure of a Modbus message Modbus TCP protocol Field Length Description Mbap header Connection management Modbus TCP communication Excep Name Description Tion Code Modbus response to a Modbus request Address Value Reading and writing parameters 4 I/O scanning to Drive Profile Lexium Byte Meaning Data type Parameter address 4.1 I/O scanning Output Bit Meaning 4.2 I/O scanning Input Inputs Bit Signal Factory setting Parameter channel Ctrl Subindex Index Function Code 3 Read Multiple Registers Modbus services Function CodeField Bytes Value Meaning Sub-function Code Diagnostics function Function Code 8 Diagnostics Function Code 16 Write Multiple Registers Function Code 23 ReadWrite Multiple Registers Object ID Object name Value Function Code 43 Encapsulated Interface Transport Example of Function Code Examples LXM32M Installation of the module InstallationDescription Order no Pin Signal Meaning Electrical installation Commissioning the device Commissioning Switching on the device Power stage supply is switched off First Setup Manual assignment of the network address Bootp / boot BootpManual / MAnu Manual Dhcp / dhcP Dhcp IP address Ethernet module, byte Assignment of the network address via Bootp Assignment of the network address via Dhcp Setting the protocol Setting the transmission rate Set the IP address of the gateway with the parameters Setting the gateway Master with Word Swap Setting the master for I/O scanning Setting I/O-ScanningActivating I/O scanning Setting the mapping for I/O scanning PLC Setting communication monitoring for I/O scanning Setting the web server 0198441113843, V1.01 Operation Indication of the operating state Operating statesBit Name Meaning Bit Name Meaning Operating state Changing the operating state Operating modes Indicating and monitoring the operating modeBit Name Description Bit Name Description Starting and changing an operating mode MODE+ACTION Overview of operating modes Operating mode Jog Operating mode Electronic Gear 24 h Operating mode Profile Torque 23 h Operating mode Profile Velocity Operating mode Profile Position Operating mode Homing LXM32M6 Operation Operating mode Motion Sequence Web server Extended settings User interface Main menu Submenu Content FTP server Accessing the FTP server FDR service Fast Device Replacement LXM32M Fieldbus communication error diagnostics Diagnostics and troubleshooting Color Status Meaning Status LEDs Meaning for EtherNet/IP Meaning for Modbus TCP Color Error indication Excep Name Description Tion Code LXM32M Cables Accessories and spare parts LXM32M Units and conversion tables Glossary Rotation TemperatureTorque Moment of inertia Terms and Abbreviations LXM32M Index LXM32M