Siemens DataNET Hub (DNH) instruction

Wall or Rack Mounting Installation, Continued

Rack Mounting

CE Installations

Wiring Requirements

The DNH rack mount configuration is designed for a standard 19-inch cabinet. The cabinet should have at least seven inches of vertical space for mounting the DNH. See Figure 1-5 for minimum width and depth mounting dimensions.

For installation sites that must conform to CE (Conformite Europeene) Certification see page 23, CE Installations.

The wiring routing and entry requirements for the DNH are dependent upon the site requirements; see page 19, Site Wiring Requirements:

•CE (Conformite Europeene) Certified Area; see Page 23

•NEC Division 2 or Non-Hazardous Areas

•Cenelec Zone 1 or Zone 2 Areas

•Rack Mounting Non-Hazardous Area.

18 • Installation

2000585-001

Image 26

Siemens DataNET Hub (DNH) user manual Rack Mounting CE Installations Wiring Requirements

Contents

Advance DataNET Hub DNH December User’s Manual 2000585-001 Copyright Notice Table of Contents Table of Contents Audience & Purpose Chapter Contents Preface Technical Support Getting Help Before You Call Safety Practices and Precautions Safety Practices and Precautions Dual Hub Modules OverviewDescription Ports Package Configurations Advance Communi- cations System DataNET Hub Hierarchy Ethernet Bridging DNH and Maxum Com Boards DataNET Hub OperationDNH Links Definitions DataNET SwitchingTransparency DataNET Hub Specifications DataNET Hub Specifications DataNET Hub Specifications Comparisons Cable Type Vendors & P/N Installation NotesCommunication DataNET Cable DataNET Hub Specifications DataNET Hub Specifications Dimension Table Description Metric Inches Zone 1 Wall Mount Zone 1 Wall Mount Dimension Table Page Installation Overview Introduction Unpacking and Inspection Description Receipt of DNH Unpacking Reporting Damage Wall or Rack Mounting Installation Instructions Package Configurations Wall Mounting Rack Mounting CE Installations Wiring Requirements Site Wiring Requirements Description Wiring of Power to DataNET HUB Recommended DataNET Cable Cable Type Vendors & P/N Installation NotesDataNET Channels DataNET Fiber Optic Cable Connections Copper Wire Site RequirementsCE Installations NEC Div 2 or Non Hazardous Areas Ethernet Communica- tion Links CE Installations CE Installation Kit Instructions CE Installations Types of Connections Wiring ConnectionsBefore You Begin Installation Note Before You Begin AC Power Mains ConnectionsDNH Power Supply Step Action Install 15-Ampere circuit breakers, disconnect switches or AC Power Mains Connections DataNET Copper Connections Description Hubs DataNET Ports Port Connections Cable Impedance Settings + Important Master Port Connectors TB15 TB18 Downlink Wiring without Signal Equalizer Board DataNET Hub Signal Equalizer Board Description Instructions Repeat the procedure for each connected port on the Hub Recommended Equalizer Board SettingsSample Calculations Calculation One Comparing Signals Example View Measurements Option 1. Connection Point Option 2. Connection Point Instructions & Examples Step Action + 2.1 dB RX & TX Connections DataNET Fiber Optic ConnectionsDataNET Fiber Optic Coupler Fiber Optic Cable Type Port Connections Page Ethernet Connections Active Ethernet Port 10BASE-T Cable Requirements Pin No MDI Function Tasks Check Overview Command Line Definitions Important ChecklistIntroduction Chapter Preview Configuring Your PC Setting Network Address Learning Hint Configuring Your PC Click Terminal Settings button Configuring Your PC Getting Started Before You Begin Password ProtectionEstablishing a Connection How to Log On Password FormatHow to Log Out How to Change At the prompt type login password IP Address Remote Connection Log On Setting Network Address Config address ip Overview IP Address How to Assign an IP AddressAssigning an IP Address Available IP Addresses Firmware Updates Click on Send Text File At the Local prompt type config address etherenetMAC Address Con- figuration Advance DataNET Hub Communication boards have status LEDs System Status LEDsBoard Status LEDs Startup LED Status For monitoring the DNH operation Hub Port LEDs Red Fault LEDYellow Warn LED Blink Codes Green Normal LED Ethernet Port LEDs Cross Link Status LED Cabling errors Example TroubleshootingConfiguration Conflicts Configuration Parameter Errors Signal Quality Problems Instructions Troubleshooting Command Descriptions Description Unique Commands Timeout on Password passwordReset Timeout off Config address ip command Config device id Command Config display Command Config netmask Command Config iproute Del Command Display Command Example local display links Display links CommandDownload Command Events Command Dn Command Dn setuptime Command Descriptions Dn module on dn module off Command Description Help Command List Command Login Command Examplelocal netstat dn clear Logout Command Netstat CommandPort Command Test Command Timeout Command Trace Command Validation timeout Command Verbose Command Captured frames Overview How to Place an Order Parts Catalog Available Parts Part Description Ordering Number Available Parts