Manuals / Siemens / Fitness & Sports / Treadmill

Siemens LC 500, Sitrans instruction manual Power, Environmental, Performance, Specifications

Models: Sitrans

1 122

Download 122 pages 51.76 Kb

Page 10

Specifications

Technical Specifications: SITRANS LC 500

Power

Supply voltage
•	maximum:	33 Vdc, (30 Vdc for IS)
•	minimum	12 Vdc at 3.6 mA (9.5 Vdc at 22 mA)
Loop current		3.6 to 22 mA / 22 to 3.6 mA (2-wire current loop)

Environmental

Location		indoor/outdoor
Altitude		2000 m max.
Ambient temperature
•	standard:	–40 oC to 85 oC (–40 oF to 185 oF)
•	ATEX-Explosion Proof	–40 oC to 70 oC (–40 oF to 158oF) for T6
		–40 oC to 85 oC (–40 oF to 185 oF) for T5 to T1
Relative humidity		suitable for outdoor (Type 4X / NEMA 4X / IP 65
		enclosure)
Installation category		II
Pollution degree		4

Performance

Measurement range
• MSP-2002-2	0 to 3300 pF
Minimum span	3.3 pF
Measurement frequency	420 kHz @ Cx = 0 pF
Accuracy	deviation <0.1% of actual measurement value
Non-linearity	0.1% full scale
Repeatability	0.1% actual measurement
Temperature stability	0.15 pF (0pF) or <0.25% (typically <0.1%) of actual
	measurement value, whichever is greater over the full
	temperature range of the transmitter

Page 4

SITRANS LC 500 – INSTRUCTION MANUAL

7ML19985GE01

Image 10

Siemens LC 500, Sitrans instruction manual Power, Environmental, Performance, Technical Specifications SITRANS LC

Contents

sitrans Instruction Manual JanuarySafety Guidelines Copyright Siemens Milltronics ProcessDisclaimer of Liability Qualified PersonnelTechnical Specifications SITRANS LC Table of ContentsTable of Contents SITRANS LC 500 Probe ConfigurationTroubleshooting SITRANS LC Table of ContentsMaintenance Error Messages and Error CodesAppendix E SITRANS LC 500, alternate versions and application details Table of ContentsAppendix D Block Diagram, and Correlation table, mA to % Appendix C HART DocumentationAppendix F Approvals Table of ContentsQuick Reference SITRANS LC GlossaryApplications SITRANS LCIntroduction The Manual Safety NotesSafety marking symbols IntroductionLong Form Abbreviations and IdentificationsShort form DescriptionEnvironmental PowerSpecifications PerformanceCommunications OutputsUser Interface SpecificationsWetted Parts WeightElectrodes Enclosure electronicSpecifications Process ConditionsApprovals Lloyds Register of ShippingThe SITRANS LC 500 variable frequency oscillator SITRANS LC 500 TransmitterOperating Principles Operation & ApplicationOperation & Application Non-conductive or conductive contentsThe formula 1 is C = In a non-conductive or irregular tank The SITRANS LC 500 electrodeOperation & Application The stilling wellMeasurement Operation & Applicationf ≈ Application SITRANS LC Operation & Applicationauxiliary Level MeasurementOperation & Application deactivation hysteresis2-state Switch Switch actionInterface Measurement Solid-state SwitchVia HART Fault SignallingVia the loop current Via the solid-state outputSITRANS LC 500 Electrode Probe Characteristics SITRANS LC 500 Probe ConfigurationProbe Configuration Process Connections Electrode AssemblyProcess Connection and Seal Configuration of SITRANS LC Seal TypesPressure and Temperature Considerations Probe ConfigurationNon-Standard Application SITRANS LC 500 ConfigurationNon-standard applications Probe ConfigurationInstallation SITRANS LC 500 InstallationHandling Electrodes Process Cautions Protection for solid-state switchMounting Instructions InstallationSITRANS LC 500 Standard Level Version InstallationSupply WiringInterconnection SITRANS LC InterconnectionInterconnection CableSelecting the correct instrumentation cable ExampleMulti-drop applications maximum cable length IS applications maximum cable lengthIIB type/class hazardous area applications maximum cable length InterconnectionTerminals Connecting SITRANS LCConnection Diagram InterconnectionInterconnection Grounding instructionsProtection for solid-state switch ground lug label / protective seal DO NOT REMOVEMetal Tanks Grounding Examples SITRANS LCSystem Grounding referencing InterconnectionSITRANS LC 500 can be connected to the tank as shown Cathodically Protected Metal TanksNon-Conductive Tanks PageGND COAX Safety GroundingInterconnection COAX GNDPage non-hazardous areaStahl barrier 9002/13-280 Communications DiagnosticsTypical PLC configuration with HART Interconnection1. See Calibration using push-button adjustment on page Current values used as signals from digital transmittersApplications for Solid-state Output InterconnectionSettings Factory SettingsSwitch Protection Diode SettingDescription SettingInterconnection The LCD display The SITRANS LC 500 User InterfaceUser Interface Menu Group How to access the dataMenu Levels 00 to 0F and 10 to 1F DetailsAdjusting the value The rotary switchAccess to a menu item The push-buttonsUser-defined Functions Transmitter VariablesTransmitter Variable UnitsStart Up Start-up SITRANS LCQuick Start Quick Start SequenceRotary Switch Positions - Quick Reference Menu levels 0 and Start up using push-button calibration overviewStart Up Calibrate the 100% setting URV - upper range value menu 0F Calibration using push-button adjustmentCalibrate the 0% setting LRV - lower range value menu 0E Start UpExample Start UpChanging stepsize value menu ExampleStart Up Calibration using HART Start UpFor situations where the capacitance values are known in advance Start Up129 Adjust for Product Build-up on Sensor Number Description38 Reset Configuration Changed Flag 128 Set Alarm Select Start UpStart Up NumberDescription 7ML19985GE01Test function MaintenanceMaintenance InspectionsMaintenance b. Confirm that Menu 08 is set to enable analog fault signalling display should readTroubleshooting SITRANS LC TroubleshootingError Codes HART Error Messages and Error CodesError Messages push-button operation ErrorAppendix A Menu Groups Analog Output Signalling loop currentDigital Output Signalling solid-state output Appendix AAppendix A Transmitter Variable Settings menu levelMenu Items MenuRange 0 to Appendix ARange 1 to 10,000 Affected Appendix AMenu Left ArrowRange 0.00 to Factory settingAppendix A Probe capacitance inProbe capaci Transmitter Variable Values menu levelAppendix A Display showsDynamic Value PV Appendix ATV0 values displayed as % Units or % of range, selectedRotary SwitchTransmitter Variables Dynamic Value menu level LeftMenu Analog Output Signalling proportional or 2-state menu levelAppendix A AffectedAppendix A Menu Analog Signalling Mode 2-state menu levelAppendix A AffectedAffected Appendix AMenu Description2-state High Fault Sig Appendix AMenu Digital Output Signalling solid-state output menu levelAppendix A AffectedAffected Appendix AMenu ArrowAppendix A S co Appendix AS cc hold RED +Description Appendix AMenu PositionMiscellaneous Appendix AAppendix A Disables 2-buttonDisables 1-button LeftLCD alphanumeric display examples Appendix B LCD display examplesAppendix B HART1 Communications for the SITRANS LC Appendix C HART DocumentationHART information HART Device Descriptor DDAppendix C SITRANS LC 500 DD Menu/Variable Organization7ML19985GE01 Bit #7 Field Device Malfunction Bit #6 Configuration ChangedHART Response Code Information Bit #5 Cold StartUsage HART Conformance and Command ClassCommand Appendix CNon-volatile Memory Data Storage General Transmitter InformationDamping information CommandBurst mode Additional Universal Command SpecificationsMultiDrop operation Units conversionsAppendix D Block Diagram, and Correlation table, mA to % SITRANS LC 500 Block DiagramCurrent in mA Correlation Table 0% - 100% to 4-20 mA or 20-4 mARange 0 - 100 % Appendix DAppendix E Standard VersionStandard Version S-Series, Threaded Appendix E SITRANS LC 500, alternate versions and application detailsStandard Version S-Series, Threaded Features Standard Version S-Series, ThreadedAppendix E S-Series, Welded Flange Standard Version S-Series, Welded and Machined Flanged VersionsFeatures Standard Version S-Series, Flanged Appendix EFeatures Standard Version DD-Series Standard Version D-Series, Machined FlangeFeatures Standard Version D-Series redundant safety e.g. Phenol, Phosgene applications, etcredundant safety e.g. Phenol, Phosgene applications, etc Features Standard Version, Probe/ Thermal IsolatorFeatures Standard Version SD-Series Appendix EProcess Connection Size Interface VersionAppendix E OptionsSanitary Versions, threaded and tri-clamp Sanitary VersionFeatures Sanitary Version, Tri-Clamp Sanitary Thread CouplingAppendix E FlangesFlange Standards 7ML19985GE01Dimensions in feet Applications ExamplesGeneric Application Calculations Appendix EAppendix E Larger tank, dimensions in feet7.32 ⋅ Appendix E Application level indicator and solid-state switch outputDevice settings 90.0Appendix E Application Analog fault signalling 2-state outputDevice settings 90.0Appendix E Menu 0B readsSITRANS LC 500 / Pointek CLS Appendix F ApprovalsCE Certificate Appendix FSCHRIFTLICHE KONFORMITÄTSERKLÄRUNG CE BescheinigungSITRANS LC 500 / Pointek CLS Appendix FAppendix F Instrument label SITRANS LC7ML19985GE01 Appendix F KEMA certificate and schedulesPage SITRANS LC 500 - INSTRUCTION MANUAL Appendix FPage 7ML19985GE01SITRANS LC 500 - INSTRUCTION MANUAL Appendix F7ML19985GE01 PageSITRANS LC 500 - INSTRUCTION MANUAL Appendix FPage 7ML19985GE017ML19985GE01 Appendix FPage SITRANS LC 500 - INSTRUCTION MANUAL Appendix FPage 7ML19985GE01SITRANS LC 500 - INSTRUCTION MANUAL Appendix F7ML19985GE01 PageSITRANS LC 500 - INSTRUCTION MANUAL Appendix FPage 7ML19985GE01Application Certificates and ApprovalsNAMUR recommendation NE SpecificationsHazardous Classified Location Appendix FApproval Non - hazardous LocationGlossary GlossarySITRANS LC 500 - INSTRUCTION MANUAL GlossaryPage 7ML19985GE01Index IndexIndex electrode characteristics 16 electrode specificationsconnect diode Quick Start Quick Reference SITRANS LCQuick Reference Quick Start SequenceRotary Switch Positions - Quick Reference Page Siemens Milltronics Process Instruments Inc 7ml19985GE01Tel 705 745-2431 Fax 705 Email techpubs@siemens-milltronics.com Subject to change without prior notice