Rotary Left Description Values Switch, Arrow | Siemens LC 500

Appendix A

(SIM) function has been selected via HART, the LCD alternately displays the text SIM or the applied simulation value for the duration of the simulation.

	Menu	Affected	Rotary	Left	Description	Values
	Item	by:	Switch	Arrow	Description	Values
			Position
	00	01	0	Off	Dynamic Value (PV)	Units or % of range, selected
						in menu 01
	10			On
	10			On

To change from menu 10 to menu 00:

1.Set the rotary switch to 0.

2.Press the RED (+) button for about a second. The LCD briefly displays : M 00

followed by : SEL 0, to indicate that menu 00 is selected. When the button is released the LCD displays the current PV value. No left-arrow is displayed at the top left corner of the LCD in menu 00.

To change from menu 00 to menu 10:

1.Set the rotary switch to 0.

2.Press the BLUE button for more than one second. The LCD briefly displays : M 10

followed by : SEL1, to indicate that menu level 1 is selected. Then the LCD displays PV, and a left-arrow is visible in the top left corner of the LCD, indicating menu level 1.

Display the Highest / Lowest Recorded Value

Menu	Rotary
Menu	Switch	Left Arrow	Description
Item	Position
	Position
02	2	Off	Highest / Lowest Recorded Value

1.Set the rotary switch to 2. The Highest / Lowest recorded values for TV currently selected are displayed alternately.

2.Press the RED (+) button to select the Highest recorded value for display,

or: Press the BLUE (–) button to select the Lowest recorded value for display,

3.Press both buttons simultaneously for more than one second to reset the recorded values back to the dynamic value of this TV. (This will also occur after a reset [power-down] of the device.)

Select the Transmitter Variable (TV) for the Primary Variable (PV).

Menu	Rotary	Left
Menu	Switch	Left	Description	Values
Item	Position	Arrow
				0	*	TVO (units are pF)
			Transmitter Variable
01	1	Off	Transmitter Variable	1		TV1 (units are user definable
			selection for PV			only via HART)
				P		TV0 (values displayed as %)

Page 60

SITRANS LC 500 – INSTRUCTION MANUAL

7ML19985GE01

Image 66

Siemens LC 500, Sitrans Rotary Left Description Values Switch, Display the Highest / Lowest Recorded Value, Arrow

Contents

Sitrans Safety Guidelines Qualified Personnel Technical data subject to changeTechnical Publications Table of Contents Maintenance Iii Appendix C Hart Documentation 113 Applications Introduction Safety Notes Safety marking symbolsManual Long Form Abbreviations and IdentificationsShort form Description Environmental PowerSpecifications Performance Outputs User InterfaceCommunications Wetted Parts WeightElectrodes Enclosure electronic Process Conditions Approvals Operation & Application Sitrans LC 500 TransmitterOperating Principles Capacitance measurement in a cylindrical metal tank Non-conductive or conductive contents Sitrans LC 500 electrode A non-conductive or irregular tankStilling well Measurement Section Probe seal Active shieldActive Inactive Application Sitrans LC Level Measurement USL Switch action Interface Measurement Via Hart Fault SignallingVia the loop current Via the solid-state output Sitrans LC 500 Probe Configuration Probe Configuration Electrode Assembly Process ConnectionsSeal Types Pressure and Temperature Considerations Non-Standard Application Sitrans LC 500 Configuration Non-standard applications Sitrans LC 500 Installation InstallationHandling Electrodes Protection for solid-state switch Mounting InstructionsProcess Cautions Sitrans LC 500 Standard Level Version Supply WiringInterconnection Sitrans LC Interconnection Cable Selecting the correct instrumentation cable Subtract the capacitance for the device Is applications maximum cable lengthMulti-drop applications maximum cable length Which allows for 560 meters on that side Connecting Sitrans LC Connection DiagramTerminals Where the stilling well is welded to the tank 7ML19985GE01 Grounding instructions Grounding Examples Sitrans LC System Grounding referencingMetal Tanks Cathodically Protected Metal Tanks Non-Conductive Tanks Safety Grounding Example Hazardous area Non-hazardous area Diagnostics Typical PLC configuration with HartCommunications Current values used as signals from digital transmitters Applications for Solid-state Output Settings Factory SettingsSwitch Protection Diode Setting Description Setting Interconnection Sitrans LC 500 User Interface LCD displayUser Interface How to access the data Menu Levels 00 to 0F and 10 to 1FDescription Menu Group Details Adjusting the value Rotary switchAccess to a menu item Push-buttons Transmitter Variables Transmitter Variable User-defined Functions Units Start Up Start-up Sitrans LCQuick Start Quick Start Sequence Rotary Switch Positions Quick Reference Num Menu levels 0 To change from menu 00 to menuTo change from menu 10 to menu Calibration using push-button adjustment Changing stepsize value menu 100% value is setCurrent percent of span = 14/20 = 70% Start Up Calibration using Hart Start Up Number Description Number Test function MaintenanceMaintenance Inspections Maintenance Troubleshooting Sitrans LC TroubleshootingIf you are unable to change settings Error Codes Hart Error Messages and Error CodesError Messages push-button operation Error Description Cause Message Appendix a Menu Groups Rotary Left Switch Description Values Position Arrow Transmitter Variable Settings menu levelStepsize Update Value Menu Items Set the rotary switch to B DampingLower Sensor Limit Upper Sensor Limit Rotary SwitchDelta Range Setting Description Values Position Affected Rotary Left Switch Mode Description Affected Rotary Left Switch ModeLower Range Value Transmitter Variable Values menu level Upper Range ValueDynamic Value, Primary Variable PV menu 00 and menu To change from menu 10 to menu Set the rotary switch to Rotary Left Description Values SwitchRotary Switch Left Arrow Description Position Display the Highest / Lowest Recorded Value Rotary Left Switch Mode Description Action Values Transmitter Variables Dynamic Value menu level Rotary Left Added Switch Arrow Analog Output Signalling proportional or 2-state menu levelUpper Threshold Delay 2-state mode Indicator Upper Threshold Setting 2-state mode Rotary Left Added SwitchArrow Indicator Mode Description Values Position Analog Signalling Mode 2-state menu level Lower Threshold Setting 2-state mode Rotary Left Mode State HighState State Low For detailed information, see Fault Signalling on Analog Fault Signalling 2-stateState mode must be selected at menu 22.0 mA Rotary Left Des Switch Digital Output Signalling solid-state output menu levelUpper Threshold Delay solid-state output Identifier Cription Lower Threshold Delay solid-state output Upper Threshold Setting solid-state outputValue Rotary Left Added Des Switch Mode Rotary Left Des Switch ModeLower Threshold Setting solid-state output Indicator Cription Digital Signalling Mode solid-state output Rotary Left Des Switch Arrow Mode Cription Action= cc Digital Fault Signalling Rotary Left Switch ModeAction Values Switch Left Arrow Description Display Meaning Position Output Signal Processing TestFactory Settings Miscellaneous Settings Rotary Switch Left Arrow Description Mode Values PositionProtection Display Switch Local Range Inversion Appendix B LCD display examples LCD alphanumeric display examplesAppendix B Hart Device Descriptor DD Appendix C Hart DocumentationHart information Simatic Process Device Manager PDM Sitrans LC 500 DD Menu/Variable Organization Hart Response Code Information Hart Conformance and Command Class Command Description Usage Number Damping information Command Description UsageGeneral Transmitter Information Non-volatile Memory Data Storage MultiDrop operation Additional Universal Command SpecificationsBurst mode Units conversions Appendix D Block Diagram, and Correlation table, mA to % Sitrans LC 500 Block Diagram Correlation % 100% to 4-20 mA or 20-4 mA Range 0 100 % Current in mAAppendix D Series Threaded Standard VersionStandard Version S-Series, Threaded Appendix E Features Standard Version S-Series, Threaded Series Cable Version With weight With anchor Features Standard Version S-Series, Flanged Series, Welded Flange Standard Version D-Series, Machined Flange Features Standard Version D-SeriesFeatures Standard Version DD-Series Series All wetted parts made of PFA Features Standard Version, Probe/ Thermal IsolatorSD-Series Probe/Thermal Isolator Thermal isolator to prevent Interface Version Interface Version, threaded optional sanitary and flanged Features Sanitary Version, Tri-Clamp Sanitary Version Flanges Flange Standards Generic Application Calculations Examples using dimensions above Capacitance in airApplications Examples Capacitance in oil Larger tank, dimensions in feet PF = 33.2 pF 90.0 Device settingsCAn 08.0 State fault signalling enabled F Hi selected Application Analog fault signalling 2-state outputCurrent loop is in 2-state mode C Hi selected CHi USL is set to 83.50 pF LSL is set to 7.3 pF Sitrans LC 500 / Pointek CLS Appendix F ApprovalsCE Certificate Appendix F CE Bescheinigung Wir erklären hiermit auf eigene Verantwortung, dass derHinweis Instrument label Sitrans LC Kema certificate and schedules Appendix F Appendix F Appendix F Appendix F Appendix F Appendix F Appendix F Application Specifications Certificates and ApprovalsNamur recommendation NE Approval Glossary Glossary 7ML19985GE01 Index NumericsIndex Wiring Index Quick Reference Sitrans LC Quick Reference Rotary Switch Positions Quick Reference Page 7ml19985GE01