Using the 230VAC Power Adapter | Socket Mobile GFK0121E specification

2

Using the 230VAC Power Adapter

The optional 230VAC Power Adapter (IC660MCA512) can be used to connect the Hand- held Monitor Charger to variety of 230 VAC power outlets by means of a standard com- puter cable (not supplied).

The Adapter has a receptacle on the top for the Hand-held Monitor Charger and an IEC 320 receptacle on the side for the computer cable.

HHM Charger receptacle in

top of Adapter

IEC 320 receptacle in

side of Adapter

Instructions

1.Set the power selection switch on the Hand-held Monitor Charger to the 230V position.

120V

230V

230V position

2.Plug the Hand-held Monitor Charger into the top receptacle on the Power Adapter unit.

3.Plug the computer cable into the IEC receptacle on side of the Power Adapter unit.

4.Connect the computer cable to a suitable 230VAC power source.

During normal operation, it is best to connect and disconnect the cable at the outlet, not at the Adapter.

2-2

Hand-held Monitor User's Guide ± June 1994

GFK-0121E

Image 12

Socket Mobile GFK0121E manual Using the 230VAC Power Adapter, Instructions

Contents

GE Fanuc Automation GFL±002 Content of this Manual Related Publications Preface Contents Chapter Introduction Hand-held Monitor Description HHM Keypad Keyswitch AccessoriesHHM Display HHM Compatibility HHM Specifications Optional Accessories Charging the Battery Pack for AC Operation Selecting 120 VAC or 230 VAC Using the 230VAC Power Adapter Instructions Battery Operation Low Battery PowerCharging the Battery Pack Replacing the Battery Pack Changing the Prom Conductive mat Permanent Installation Configuring a Permanently-installed HHM HHM Installation Instructions Cutout Installing the D-Shell HHM Connector SER Installing a Separate Hand-held Monitor Connector Mounting the HHM Connector Making the Bus Connections Chapter Getting Started Setting the HHM Baud Rate Powerup Error Messages Displaying the Home Menu Main HHM Screens Configuring the Hand-held Monitor Changing the HHM Device Number Changing the HHM Display Language Selecting the Host CPUEnabling/Disabling Automatic Shutoff Enabling/Disabling the Ability to Clear Faults Enabling/Disabling the Ability to Force I/O Circuits Testing Operation of the Hand-held Monitor Testing the Internal ElectronicsTesting the Keypad Testing the Display Screen Chapter Device Configuration Overview Online or Offline Configuration Starting ConfigurationOnline Configuration Offline Configuration Displaying the Configuration Menus Completing the Program Block ID Screens To Set the I/O Map for a Remote I/O Scanner Configuration Notes Configuring the Remote Drop ConfiguringGenius Blocks Copying a ConfigurationConfiguring Block Features Configuration Instructions Configure Additional Features Change the Bus AddressSelect a PLC Reference Address Configuring Individual Field Control Modules Disable the I/O ScanConfigure Data Addresses and Lengths Configuring Module Features Add Modules and Assign ReferencesAssign I/O References for the Module Chapter Monitoring the Bus and its Devices Displaying Information About Bus Devices Selecting Another Device Switching a Dual Bus Monitoring the Bus Status Monitoring a Genius Block Monitor Block Display for Discrete I/O and Input BlocksMaking the Block Active Block References Monitor Block Display for Discrete Relay OutputBlocks Monitor Block Display for Analog Blocks Preset Outputs Monitor Block Display for a High-speed Counter Block Monitor Block Display for a PowerTRACBlock Calculated Data Basic Monitor/Control Display Format Diagnostics Clearing Circuit FaultsForcing an Input or Output Forcing an Analog, RTD, or Thermocouple Value Monitor/Control Reference Displays for a PowerTRAC Block PowerTRAC Data SequenceSelecting a Memory Type or Address PowerTRAC Status Inputs Screens PowerTRAC Calculated Data ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs Screens Monitoring/Controlling Remote Drop Data Displaying Other Circuits Displaying and Clearing Remote Drop Faults Clearing FaultsForcing a Circuit Changing the Display Mode Monitoring/Controlling Field Control DataDisplaying Another Reference Returning to the Previous Menu Displaying Field Control Faults Clearing Field Control Faults Pulse Testing Outputs on Discrete Genius Blocks Clearing Pulse Test FaultsPulse Test Error Messages Executing a Pulse Test Chapter Reading CPU Memory General Instructions Series 90 PLC Series Six PLC Enter or Change the PLC TypeEnter or Change the Memory Location Series Five PLC Data Changing the Data Format Changing the Selected Address Chapter Error Messages Powerup Error Messages Operating Error Messages Configuration Error Messages Index Index-2 Index-3 Index-4