HHM Display, Keyswitch, Accessories | Socket Mobile GFK0121E

1

The HHM Display

The Hand-held Monitor has a 4-line LCD screen. On a new Hand-held Monitor, displays are in English. The display language can easily be changed to French, German, or Italian. (Instructions for changing the display language are on page 3-5).

In addition to alphanumeric characters, the display uses the following special characters:

IT	tri-stateinput.
OT	Output with Feedback, or block with both inputs and outputs.

4circuit is forced OFF.

1circuit is forced ON.

Orelay block point is forced open.

Crelay block point is forced closed.

BS	circuit controls a Bus Switching Module.

?reference address or Device Number not yet assigned.

*reference address is out of range for the presently-selected HHM host.

For a list of other HHM abbreviations and their meanings, select F3 (HELP) from the

HHM Utilities menu.

Keyswitch

The Hand-held Monitor's keyswitch can be used to restrict access to certain features of the HHM.

With the key present, the switch can be placed in either ªconfigureº (cfg) or ªmonitorº (mon) position.

cfg with the switch in Configure position, all HHM functions are available. In this mode, the Hand-held Monitor can be configured to determine which of its fea- tures will be usable once the key is removed.

mon: with the keyswitch in Monitor position, the HHM can monitor bus and block data. Additional HHM functions, such as clearing faults or configuring I/O blocks, can be used in Monitor mode only if the HHM has been set up to permit their use.

The key must be present to move the switch from Monitor to Configure mode position; it can only be removed in MON position. Two identical keys are supplied with each Hand-held Monitor. The key should be removed if system security is a concern.

Accessories

The Hand-held Monitor comes with:

HA sturdy removable leather case. The case has a rear tab with snap closure for carrying the HHM on a belt. The handle can be pivoted back to stand the Hand-held Monitor upright on a table.

HA rechargeable battery pack.

HA battery charger/adapter with 8-ft cord.

HTwo keys for the mode-selection keyswitch.

HA removable 5 ft (1.5 meter) coiled communications cable.

GFK-0121E

Chapter 1 Introduction

1-3

Image 8

Socket Mobile GFK0121E manual HHM Display, Keyswitch, Accessories

Contents

GE Fanuc Automation GFL±002 Content of this Manual Related Publications Preface Contents Chapter Introduction Hand-held Monitor Description HHM Keypad HHM Display KeyswitchAccessories HHM Compatibility HHM Specifications Optional Accessories Charging the Battery Pack for AC Operation Selecting 120 VAC or 230 VAC Using the 230VAC Power Adapter Instructions Battery Operation Low Battery PowerCharging the Battery Pack Replacing the Battery Pack Changing the Prom Conductive mat Permanent Installation Configuring a Permanently-installed HHM HHM Installation Instructions Cutout Installing the D-Shell HHM Connector SER Installing a Separate Hand-held Monitor Connector Mounting the HHM Connector Making the Bus Connections Chapter Getting Started Setting the HHM Baud Rate Powerup Error Messages Displaying the Home Menu Main HHM Screens Configuring the Hand-held Monitor Changing the HHM Device Number Enabling/Disabling Automatic Shutoff Changing the HHM Display LanguageSelecting the Host CPU Enabling/Disabling the Ability to Clear Faults Enabling/Disabling the Ability to Force I/O Circuits Testing Operation of the Hand-held Monitor Testing the Internal ElectronicsTesting the Keypad Testing the Display Screen Chapter Device Configuration Overview Online or Offline Configuration Starting ConfigurationOnline Configuration Offline Configuration Displaying the Configuration Menus Completing the Program Block ID Screens To Set the I/O Map for a Remote I/O Scanner Configuration Notes Configuring the Remote Drop ConfiguringGenius Blocks Copying a ConfigurationConfiguring Block Features Configuration Instructions Select a PLC Reference Address Configure Additional FeaturesChange the Bus Address Configure Data Addresses and Lengths Configuring Individual Field Control ModulesDisable the I/O Scan Assign I/O References for the Module Configuring Module FeaturesAdd Modules and Assign References Chapter Monitoring the Bus and its Devices Displaying Information About Bus Devices Selecting Another Device Switching a Dual Bus Monitoring the Bus Status Monitoring a Genius Block Monitor Block Display for Discrete I/O and Input BlocksMaking the Block Active Block References Monitor Block Display for Discrete Relay OutputBlocks Monitor Block Display for Analog Blocks Preset Outputs Monitor Block Display for a High-speed Counter Block Monitor Block Display for a PowerTRACBlock Calculated Data Basic Monitor/Control Display Format Forcing an Input or Output DiagnosticsClearing Circuit Faults Forcing an Analog, RTD, or Thermocouple Value Selecting a Memory Type or Address Monitor/Control Reference Displays for a PowerTRAC BlockPowerTRAC Data Sequence PowerTRAC Status Inputs Screens PowerTRAC Calculated Data ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs Screens Monitoring/Controlling Remote Drop Data Displaying Other Circuits Forcing a Circuit Displaying and Clearing Remote Drop FaultsClearing Faults Changing the Display Mode Monitoring/Controlling Field Control DataDisplaying Another Reference Returning to the Previous Menu Displaying Field Control Faults Clearing Field Control Faults Pulse Testing Outputs on Discrete Genius Blocks Clearing Pulse Test FaultsPulse Test Error Messages Executing a Pulse Test Chapter Reading CPU Memory General Instructions Series 90 PLC Enter or Change the Memory Location Series Six PLCEnter or Change the PLC Type Series Five PLC Data Changing the Data Format Changing the Selected Address Chapter Error Messages Powerup Error Messages Operating Error Messages Configuration Error Messages Index Index-2 Index-3 Index-4