HHM Installation Instructions, Cutout | Socket Mobile GFK0121E

2

HHM Installation Instructions

1.Select a suitable location for the HHM. Environmental specifications are listed on page 1-5. The location must have 115 VAC or 230 VAC power.

2.Cut an opening 3.75I(9.53cm) wide x 8I(20.32cm) high in the panel. Drill four mounting holes as shown below.

4.38in

(11.13cm)

3.75in

(9.53cm)

Cutout

1.00in (2.54cm)

6.00in

(15.24cm)

1.00in (2.54cm)

3. Attach the bracket to the HHM with the screws, washers, and lockwashers provided.

(4) holes for mounting on panel

(2) holes for mounting to back of Hand-held Monitor

4.Using appropriate hardware (not provided), mount the HHM and bracket in the cutout.

5.Connect the power cord to the HHM, and connect the signal cable to the connector.

GFK-0121E

Chapter 2 Hardware Setup

2-7

Image 17

Socket Mobile GFK0121E manual HHM Installation Instructions, Cutout

Contents

GE Fanuc Automation GFL±002 Related Publications Content of this Manual Preface Contents Chapter Introduction HHM Keypad Hand-held Monitor Description HHM Display KeyswitchAccessories HHM Compatibility Optional Accessories HHM Specifications Selecting 120 VAC or 230 VAC Charging the Battery Pack for AC Operation Instructions Using the 230VAC Power Adapter Low Battery Power Battery OperationCharging the Battery Pack Replacing the Battery Pack Changing the Prom Conductive mat Configuring a Permanently-installed HHM Permanent Installation Cutout HHM Installation Instructions SER Installing the D-Shell HHM Connector Mounting the HHM Connector Installing a Separate Hand-held Monitor Connector Making the Bus Connections Chapter Getting Started Powerup Error Messages Setting the HHM Baud Rate Main HHM Screens Displaying the Home Menu Changing the HHM Device Number Configuring the Hand-held Monitor Enabling/Disabling Automatic Shutoff Changing the HHM Display LanguageSelecting the Host CPU Enabling/Disabling the Ability to Force I/O Circuits Enabling/Disabling the Ability to Clear Faults Testing the Internal Electronics Testing Operation of the Hand-held MonitorTesting the Keypad Testing the Display Screen Chapter Device Configuration Overview Starting Configuration Online or Offline ConfigurationOnline Configuration Offline Configuration Displaying the Configuration Menus To Set the I/O Map for a Remote I/O Scanner Completing the Program Block ID Screens Configuring the Remote Drop Configuration Notes Copying a Configuration ConfiguringGenius BlocksConfiguring Block Features Configuration Instructions Select a PLC Reference Address Configure Additional FeaturesChange the Bus Address Configure Data Addresses and Lengths Configuring Individual Field Control ModulesDisable the I/O Scan Assign I/O References for the Module Configuring Module FeaturesAdd Modules and Assign References Chapter Monitoring the Bus and its Devices Selecting Another Device Displaying Information About Bus Devices Monitoring the Bus Status Switching a Dual Bus Monitor Block Display for Discrete I/O and Input Blocks Monitoring a Genius BlockMaking the Block Active Block References Monitor Block Display for Analog Blocks Monitor Block Display for Discrete Relay OutputBlocks Monitor Block Display for a High-speed Counter Block Preset Outputs Calculated Data Monitor Block Display for a PowerTRACBlock Basic Monitor/Control Display Format Forcing an Input or Output DiagnosticsClearing Circuit Faults Forcing an Analog, RTD, or Thermocouple Value Selecting a Memory Type or Address Monitor/Control Reference Displays for a PowerTRAC BlockPowerTRAC Data Sequence PowerTRAC Calculated Data Screens PowerTRAC Status Inputs ScreensPowerTRAC Extra Calculated Data Lpio Screens PowerTRAC Control Outputs Screens Displaying Other Circuits Monitoring/Controlling Remote Drop Data Forcing a Circuit Displaying and Clearing Remote Drop FaultsClearing Faults Monitoring/Controlling Field Control Data Changing the Display ModeDisplaying Another Reference Returning to the Previous Menu Clearing Field Control Faults Displaying Field Control Faults Clearing Pulse Test Faults Pulse Testing Outputs on Discrete Genius BlocksPulse Test Error Messages Executing a Pulse Test General Instructions Chapter Reading CPU Memory Series 90 PLC Enter or Change the Memory Location Series Six PLCEnter or Change the PLC Type Data Series Five PLC Changing the Selected Address Changing the Data Format Powerup Error Messages Chapter Error Messages Configuration Error Messages Operating Error Messages Index Index-2 Index-3 Index-4