Recipe Storage and Recall | Sterling Plumbing 882 00276.00 instruction

Section 4: Advanced Operations/ Control Functions

4.1 Recipe Storage and Recall

A maximum of ten (10) recipes can be stored and retrieved with the Digital Dosing controller in the Recipe Storage/Recall mode. Recipes are stored using a two-digit identification

number. Pressing at any time will exit the Recipe Storage/Recall mode.

Recipe Storage

To store the current recipe:

Step 1:

•Press the Recipe Storage/Recall key (). A two-digit number (01 through 10) will appear on the screen. This is the recipe I.D. number.

Step 2:

•Use the Arrow keys to select the desired recipe number.

NOTE: A new recipe stored under the ID number of an existing recipe will overwrite the existing recipe number without warning.

Digital Dosing Units

41

Image 41

Sterling Plumbing 882 00276.00 specifications Advanced Operations/ Control Functions, Recipe Storage and Recall

Contents

SDD Series Digital Dosing Additive Feeders Table of Contents Introduction Digital Dosing Units Keypad and LED Display Controller Keys and Symbols Symbols Mounting Quick Start-upUnpacking DD Discs Calibration Number Recipe Setup for Injection MoldingDT Discs Calibration Number DP Discs Calibration Recipe Setup for Extrusion Digital Dosing Units Input Number Manufacturer Motor Color Digital Dosing Units Digital Dosing Units Digital Dosing Units RPM Digital Dosing Units Digital Dosing Units Digital Dosing Units Initial Installation Initial Installation and Operation Electrical Diagram Electrical diagram of connections Signal Converter with AC Power Supply Extruder Follower Interface Signal ConverterDiagram of analog inputs Initial Operation Signal Converter with DC Power SupplyVDC Mini Power Supply Recipe Input Injection Molding Injection Molding Step Step Step Operation Injection Molding Recipe Input Extrusion Constant Extrusion Constant Standard Extrusion Constant, parameter 3 is skipped Step Step Operation Extrusion Constant Recipe Input Extrusion Proportional Extrusion Proportional Extruder Follower Option Step Step Operation Extrusion Proportional Extruder Follower Option Calibration Determining the Calibration Weight Repeat steps 3 and 4 four 4 more times Digital Dosing Units Recipe Storage Advanced Operations/ Control FunctionsRecipe Storage and Recall Recipe Recall Clearing the Totalizer Acknowledging Alarms Level switches probes Alarms Communication Protocol Interfaces Maintenance Intervals MaintenanceRemoving the Shear plate DD feeder only Removing the shear plate Dismantling the Dosing Station Cleaning the DD Digital Dosing StationInstalling the shear plate Installing the Dosing Station Removing the Dosing Disc Installing the Dosing DiscChanging the Dosing Disc in the DT Digital Dosing Station DD Discs Installing Different Types of Dosing DiscsRemoving / Replacing the Wiper in the DT Dosing Station Cleaning the DT Dosing Station Disc Exchangeable StationsDP Discs Calibration See Appendix D for fuse part numbers Replacing Fuses Malfunctions Error Codes Appendix a TroubleshootingGeneral Troubleshooting Unit Will Not Operate Error Codes Recipe Formulas Determining the Software Setup FactorInjection Molding Recipe Limitations for Injection Molding Recipe Limitations Extrusion Extrusion Max. input frequency = Hz Appendix B Basic Parameter SettingsExtrusion Mode Example Probe Example Digital Dosing Units Disc Dosing Factor Disc Guide 20 kg/h DT30 204010F Default Calibration # 150 grams/rev One 1 for Granule Disc Dosing Factor TableProcessing Option Hopper Level Probe Virgin Starter Calibration Parameters Set-up of Factory Set Operating Parameters Ext = Span factor sf calculated using sf=1000/rpm@10vdc Page Station 1 Digital Dosing Unit Side View TOP View Station 2 Digital Dosing Unit General Wiring Diagram for Bauer Motor Page C150 Controller Injection Dosing Disc/Shear Order Numbers Appendix D Spare Parts ListReplacement Motor Order Numbers Control System Order Numbers Page Technical Assistance Service DepartmentParts Department Sales Department