3. BYPASS COPYING

When the desired size of paper is not set in any of the drawers, or when you want to make copies on A3- wide or non-standard sized paper, use the sheet bypass.

The modes below are available even in bypass copying if the paper size is specified:

- automatic paper selection

- automatic magnification selection

- duplex

- edge erase

- image shift

- book centre erase

- dual-page

- full image

- 2 IN 1 / 4 IN 1

- trimming/masking

- mirror image

- centring

- image repeat

- staple sorting

- magazine sort

- saddle stitching

- hole punching

 

 

In these cases, the setting procedures of the following two types of paper are different:

-Bypass copying on standard size and A3-wide paperPage 6-7

-Bypass copying on non-standard size paperPage 6-9

If you want to make copies on thin paper, thick paper, OHP film, sticker label, special paper, etc., make

bypass copies.

Page 6-11, 6-12

*You can also set THIN paper (64~79g/m2), THICK1 paper (106~163g/m2) and OHP films in the drawers. Page 2-7

Bypass Copy Mode

- Refer to the table below and select the mode corresponding to the paper that has been set. Otherwise,

 

paper jams may result or the image quality could deteriorate.

 

 

 

- The number of sheets that can be set at a time differs depending on the paper type. Setting more than the specified

 

number of sheets at a time may cause copier failure or the paper jams. Be sure to set within the specified range.

 

- It takes from 30 to 60 seconds to switch modes among “PLAIN”, “THICK1”, “THICK2”, “THICK3”, “THICK4”,

6

“SPECIAL” and “OHP FILM” for adjustment, and from 30 to 120 seconds between “THIN” and other modes.

- If the BYPASS MISFEED

symbol flashes, pull out the paper and place it on the sheet bypass again.

 

Page 9-13

 

 

 

 

 

 

 

 

 

 

- When copying is finished, the lamp of the FUNCTION CLEAR key lights. Either press the FUNCTION

 

CLEAR key, or wait 45 seconds before the bypass copying mode automatically returns to the default mode.

 

 

 

 

 

 

 

Corresponding Paper Type

Paper Size

Maximum Capacity

 

 

 

 

 

 

 

 

THIN (64-79g/m2)

(Standard size)

130 sheets

 

 

 

A/B format: A3,A4,A4-R,A5-R,A6-R,B4,B5,B5-R,

 

 

 

 

 

 

 

 

 

PLAIN (80-105g/m2)

FOLIO(210x330mm),A3-wide(305x457mm)

2

 

 

 

LT format: LD(11”x17”), LG(81/2x14”),

115 sheets (90g/m )

 

 

 

100 sheets (100g/m2)

 

 

 

LT(11”x81/2), LT-R(81/2x11”), ST-R(51/2x81/2),

 

 

 

 

THICK1 (106-163g/m2)

 

60 sheets (120g/m2)

 

 

 

COMP(101/8x14”), 13”LG(81/2”x13”),

60 sheets (160g/m2)

 

 

 

8.5”SQ(81/2”x81/2”)

 

 

 

 

THICK2 (164-209g/m2)

 

40 sheets (200g/m2)

 

 

 

(Non-standard size)

 

 

 

 

THICK3 (210-256g/m2)

 

40 sheets (220g/m2)

 

 

 

Length: 100-305mm; Width: 148-457mm

40 sheets (250g/m2)

 

 

 

 

 

 

 

 

 

 

 

 

 

THICK4 (257-280g/m2)

 

 

40 sheets

 

 

 

 

 

 

 

 

Sticker labels (THICK2)

 

 

40 sheets

 

 

 

 

 

 

 

 

Special paper

(Standard size)

40 sheets

 

 

 

 

 

 

 

A3, A4, A4-R

 

 

 

 

 

 

 

 

 

OHP FILM

(Standard size)

40 sheets

 

 

 

A4

 

 

 

 

 

 

 

 

 

 

 

 

 

* The copier stops its operation when the paper set on the bypass guide has run out even if there is the same size of copy paper in the drawer.

* When the finisher (optional) is installed, the images may not output easily according to the environment.

6-5

Page 100
Image 100
Toshiba e-STUDIO211c/311c manual Bypass Copying, Bypass Copy Mode