Check on Enable TCP/IP and enter IP Address | Toshiba GA-1031

7

8

Check on Enable TCP/IP and enter the

IP Address.

●Enter the Subnet Mask and Default Gateway address if necessary.

●Go to step 9.

Check off IP Address in NVRAM.

●“Enable DHCP” should be checked as a default setting. Ensure that it is enabled.

IP ADDRESS

ASSIGNING

SUPPLEMENTS:

●When the "IP Address in NVRAM" option is enabled, the IP address that was previously obtained from the DHCP is stored in NVRAM. The NIC uses the IP address stored in NVRAM the next time the printer is powered on, instead of obtaining an IP address from the DHCP server. In order to avoid any network address conflicts, it is recommended that you do not use the "IP Address in NVRAM" option when using the "Enable DHCP" option.

●If there is a WINS server and you want to use a WINS name for the NIC, enter the NetBIOS Name and the IP address of the Primary NetBIOS Name Server. When using a DHCP server to obtain an IP address, TCP/IP printing cannot be performed because the IP address changes each time the printer is powered on. By configuring the port with a WINS name instead of an IP address, TCP/IP printing can be performed.

21

Image 23

Toshiba GA-1031 manual Check on Enable TCP/IP and enter IP Address, Check off IP Address in Nvram

Contents

Page FCC Notice Page Table of Contents Setup the Print Server with Windows NT4.0/2000 109 Installing the Printer Driver for Windows Reset a Printer and NIC 176 Print a Test 177 Troubleshooting Introduction Network Requirements RequirementsHardware Others Example of connection on a peer-to-peer type network Example of connection on a client-server type network Setup for Client Server Network for Windows Setup Flow For Macintosh Setup for the Peer-to-Peer Type NetworkFor Windows Network Setup Supplement Assigning the IP Address Standby Mode, press Key Assigning the IP Address from the Control PanelUse Dhcp Server Press + on the Dial Keypad to select Complete Network setting is executingPress Display returns to the TCP/IP menu Assign the IP Address Manually Network setting is executing Assigning the IP Address using MAP Click on your printer unit Click on Setup TCP/IP Check off IP Address in Nvram Check on Enable TCP/IP and enter IP Address Complete the IP Address setting Press On the Dial Keypad To select the Frame Type Novell Settings Press to select Press the numeric key of the desiredFrame type on the Dial Keypad Press To select Auto Network setting is executing Press + on the Dial Keypad to select Apple Talk Appletalk SettingStandby Mode, press If you want to cancel the AppleTalk setting Press Page Using with PEER-TO-PEER Utility For IPX/SPX Protocol PEER-TO-PEER UtilitiesRequired Environment For TCP/IP Protocol Insertdrive. the CD-ROM into the CD-ROM Installation Click on Next Installation Notes are displayed Click on Yes Click on IP P2P setup Field of Max Hops for, input a Files are installedIs shown. It is the default port Click on Next Click on Find Printers Printers list Next, installing the printer driverClick on Add Printer is added to the Available INSTALLINGTHEPEER-TO-PEERUTILITY FORIPX/SPX Click on IPX P2P setup Available Printers shows S flag Click on Next Files are installedMake sure the printer is displayed Under Available Printers Make sure the printer displayed under Installation is completed Uninstalling the Peer-to-Peer Utility for TCP/IP Uninstallingthe PEER-TO-PEER Utility Click on OK Restart the computer Uninstalling the Peer-to-Peer Utility for IPX/SPX Click on OK Click on Yes Setup the Print Server Set-up Example NetWare 3.x Setup Creating a print queue Setting up with PconsoleSelect File Server Creating the print server Print Server Setup Page Assigning a print queue Enter the priority and press the Enter Key Queue is assigned Available Queues appears Select a created queue Print Server Setup Setting Up Notify Options for the Printer Press the Esc key to return to the menu Primary File ServerPreferred File Servers Available File Servers list is displayedPage Setup the Print Server Nwsrv Setup in NDS Mode Start NetWare Administrator Setting up NetWare AdministratorStarting NetWare Administrator Administrator Printer Click on the container object to create Click on Browse of Print Queue Volume indicated by a in the figureCreate Print Queues appears Print Queue Name Creating the printer Assigning the print queue Click on OK Printer is created Details of the created print server Create Print Server windowEnter the name of the print server Under Print Server Name Allocating the printer Print server is created Press Alt+F10 to complete the confirmation Setup in Bindery ModeConfirmation before setting up Confirm Bindery Context ORG Starting Pconsole Creating the print server Information menu and press the Enter Choose the created print serverPrint Server Information menu Choose Printer from the Print Server Enter printer number at Printer No Printer Xxxxx configurationSelect the created printer and press Is the name of the printer created Press the Esc key four times When Save Changes? appearsWhen Exit? appears, choose Yes and press the Enter key Press the Esc key twice Select Print Servers in the Available Option menu When a message appears, press the Enter keyProblems and press Enter key Start the Pconsole utilityPage Setup the Print Server Setup in NDS Mode This is performed on the workstation Creating a print queue Indicated by a in the figure at Click on Browse Print Queue VolumeEnter the name of the print queue Under Print Queue Name Creating the printer Assigning the print queue Click on OK Printer is created Create Print Server window Allocating the printer Supplements Page With Windows NT4.0/2000 Confirming the TCP/IP Print Services Preparation for Setting up Creating a Shared Printer Click on OK Click on Close Verify that the check box for IP address of the printer is addedTo the list of Available ports Add Printer Wizard Select Windows 95 from the list Click on Next Check on Shared \ENGLISH\ESTUDIO\WIN9598\PCL6 Choose Yes or No as necessary, and click on Finish Printer is created Log on to Windows 2000 as a user With Administrator or Power User Standard TCP/IP Port at Type When Using the TCP/IP PrintingSelect Local printer Select Create a new port and select Select Custom and click on Settings Select Raw or LPR under Protocol Enter 10001 at Port Number Check on Snmp Status EnabledEnter PORT1 for the Queue Name Check on Snmp Status Enabled Drivers for Windows 2000/XP at Copy Click on OK Click on Next Click on Finish Click on Have Disk 100 101 Click on OK Click on Have Disk When Using the IPP102 Select the printer driver to be Installed103 104 Click on Additional Drivers 105Select the printer driver and select Sharing... from the File menu Insert the printer driver CD-ROM Click on OK 106 107 Click on OK Printer drivers are installed 108 109 Installing the Printer Driver 110 Installing the Printer DriverFeatures of Each Printer Driver 111 Insert the Printer kit CD-ROM into the CD-ROM drive Installation from the CD-ROM112 Select the Group Number, and click Click on the appropriate Setup for113 Windows Version Select the Peer-to-Peer Port, and click On Next SelectPaper. the Emulation and Default114 Select the network printer and click on OK 115Click on Browse Enter the printer name, and click on Next 116 Select the Program Folder to be Created, and click on Next Click on Finish Complete the installation117 118 Installation by Adding PrinterWindows 95/98/Me On OK 119Select the network printer and click Click on OK Select the printer to be used, and click on Next 120 Select to print a test page or not, then 121If necessary, change the Printer name, then click on Next Select how the printer is to be Controlled Click on Start, select Settings, Then click on PrintersWindows NT4.0 122 Select the port added in the Peer-to 123Select the printer connected to Server, and click on OK Printer kit into the CD-ROM drive 124Insert the CD-ROM included with 125 Double-click on Add Printer to start Printer Wizard Windows 2000/XP126 Server, and click on Next 127Next to browse for a printer then 128 129 130 Copying the PageMaker PPD file 131 Setting the Options Configuration 132 Selectitems. the installed options for eachClick on OK to save the settings After programs have been removed Uninstalling the Printer DriverRun the Uninstall.exe 133 134 Install Agfa Font Manager 135 Checkinstall. the components you want to Click on OK Click Finish 136 137 Uninstall Agfa Font Manager 138 Description of Screen Getting Started with Agfa Font Manager 140 141 For Macintosh 142 System RequirementSystem Requirements 143 Copying the PPD File Make sure that Active is selected for AppleTalk Select the Driver144 Click on the Apple menu, and select Chooser 145 Option Setup Exit the Chooser 146 ➁ Toner Saving Printer Specific Options147 Printer Specific Options ➀ Offset Stack ➅ Edge Smoothing 148➃ Duplex ➄ Media Type 149 Printer Specific Options ➇ Resolution 150 151 Netpanel Function 152 Installing Netpanel Click on a language of your Operating Installing153 154 Click on Setup utilities Click on Netpanel setup Enter the IIS virtual directory 155 Decide whether to read the Readme file at this time 156 157 Uninstalling 158 159 Starting NetpanelRequired Environments 160 Browsing with NetPanel 161 Log ➂ Task bar Description of Screen162 ➀ Logo ➁ Topic bar Open the Window and display Help Using Help163 Click on the Help button on Control bar Log Printer Discovery Operating FlowFor the Normal User 164 165 For the Administrator Printer Management 166 Group Management NetPanel Setting167 Server Management 168 Printer DiscoveryPrinter Discovery Main ➀ System Properties Searching Result Display169 ➃ Search Result List 170➁ Connection Properties ➂ Status Diagnose 171 Printer ManagementPrinter Management Search 172 ➀ Reset PrinterPrinter Management Main 173 ➁ Printer Configure➂ NIC Configure 174 ➃ Novell Configure➄ Device Password 175 Reset Printer and Test Print Select the printer that you want to Reset a Printer and NICClick on Reset Printer Now Operating result is displayed 176 177 Clickbar. on Reset Printer on the Task Select desired testPrint a Test 178 Printer ConfigureGeneral Properties ➁ Top Priority Cassette ➀ Select Default Input TrayInput Tray Properties 179 180 Output Bin Properties ➀ Copies ➁ Default Paper SizePaper Properties 181 ➀ Lines Per Printer Setting Properties182 183 184 ➈ Emulation Setting➉ Print Postscript Error Device Password 185 PCL Font Properties 186 Group Management 187 NIC ConfigureProtocols Configuration 188 IP Configuration ➁ Zone Name Apple Talk Configuration189 ➀ Printer Name ➁ LPD Banner System Configuration190 ➀ Frame Type ➃ Type of Startup 191➂ Print on Startup 192 Novell ConfigureNovell Configuration 193 Device PasswordDevice Password ➀ Printers shared in Windows NT Server Server ManagementServer Management Main 194 195 Server Management Main Page of Windows NT Server 196 Install a Printer to a File Server Server Printer is installed to the File197 Select or specify the printer Click on Continue Remove a Printer from a File Server198 Printer is removed from the File 199 200 Deleting Print Jobs 201 Selected print jobs are canceled 202 Group ManagementGroup Management Main 203 Create a Group 204 Delete a Group Select a group and click on OK View Group and Printer205 Clickbar. on View Group on the Task Printer status 206Display the printer properties page or 207 Add a Printer to a Group Remove from the list Remove a Printer from a Group208 209 210 Netpanel SettingNetPanel Setting Main 211 Administrator SettingChange the Administrator Password 212 WNP Setting 213 Discovery Setting 214 215 MAP 216 Password for MAPMAP Click on a language of your Operating System Install MAP217 218 Click on MAP setup 219 Select Programs from Start menu Click on MAP Setup in the Map folderStart MAP 220 221 Network Administrator page is Displayed Enter http//xxx.xxx.xxx.xxx/ at Network Administrator page is222 Run the WWW Browser Enter each field that applies Select Setup NetWare from Network Administrator223 224 Enter the passwordClick on Accept Setting Displayed Network Interface Card is automatically restarted Select Setup AppleTalk from Network Administrator225 Factory defaults are restored Restart the printer Restore Factory DefaultsClick on Factory Defaults Enter the password and click on Restore Factory Defaults 227 Troubleshooting 228 Netpanel Error 229 Error messages 230 231 When Printing Cannot be Performed 232 233 Specifications and Other Information 234 Specifications of the Units 235 Test Print SampleDemo 236 Configuration 237 NIC Status 238 PCL Font List 239 240 241 PS Font List 242 243 Status Log 244 Group Management List 245 List of Internal PCL Fonts 246 247 List of Internal PS Fonts 248 E1-17089B Kanda NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8442, Japan