Manuals / Toshiba / Computer Equipment / Printer

Toshiba GA-1031 manual Novell Settings, Press On the Dial Keypad To select the Frame Type

Models: GA-1031

1 252

Download 252 pages 21.53 Kb

Page 25

NOVELL SETTINGS

When using the NetWare server for printing, the Novell Settings must be configured to enable

connection to the printer via the IPX/SPX protocol.

1 In Standby Mode, press

key.

●The PROGRAM menu is displayed.

2 Press + on the Dial Keypad to select INITIAL SETUP.

3 Press + on the Dial Keypad to select NETWORK.

●NETWORK is outside of the Message Display

Panel. Press to display the desired item.

4	Press	+	on the Dial Keypad
	to select NETWARE.
5	Press	+	on the Dial Keypad
	to select IPX/SPX.

6 Press on the Dial Keypad to select ENABLE.

●The display returns to the TCP/IP menu.

7 Press

+

on the Dial Keypad

to select the FRAME TYPE.

●If you do not have to change the frame type of the NIC, skip to Step 9.

PROGRAM

01.DEFAULT SETTING

02.LISTS 03.INITIAL SETUP

INITIAL SETUP

02.LANGUAGE

03.TERMINAL ID 04.NETWORK

TIP

“03. TERMINAL ID” appears on the menu only

when the FAX option is installed.

NETWORK

01.COMPLETE

02.TCP/IP

03.NETWARE

NETWARE

01.IPX/SPX

02.FRAME TYPE

IPX/SPX

1.ENABLE

2.DISABLE

NETWARE

01.IPX/SPX

02.FRAME TYPE

IP ADDRESS

ASSIGNING

23

Image 25

Toshiba GA-1031 manual Novell Settings, Press On the Dial Keypad To select the Frame Type

Contents

Page FCC Notice Page Table of Contents Setup the Print Server with Windows NT4.0/2000 109 Installing the Printer Driver for Windows Reset a Printer and NIC 176 Print a Test 177 Troubleshooting Introduction Hardware RequirementsNetwork Requirements Others Example of connection on a peer-to-peer type network Example of connection on a client-server type network Setup for Client Server Network for Windows Setup Flow For Windows Setup for the Peer-to-Peer Type NetworkFor Macintosh Network Setup Supplement Assigning the IP Address Use Dhcp Server Assigning the IP Address from the Control PanelStandby Mode, press Key Press Network setting is executingPress + on the Dial Keypad to select Complete Display returns to the TCP/IP menu Assign the IP Address Manually Network setting is executing Assigning the IP Address using MAP Click on your printer unit Click on Setup TCP/IP Check off IP Address in Nvram Check on Enable TCP/IP and enter IP Address Complete the IP Address setting Press On the Dial Keypad To select the Frame Type Novell Settings Frame type on the Dial Keypad Press the numeric key of the desiredPress To select Auto Press to select Network setting is executing Standby Mode, press Appletalk SettingPress + on the Dial Keypad to select Apple Talk If you want to cancel the AppleTalk setting Press Page Using with PEER-TO-PEER Utility Required Environment PEER-TO-PEER UtilitiesFor TCP/IP Protocol For IPX/SPX Protocol Insertdrive. the CD-ROM into the CD-ROM Installation Click on Next Installation Notes are displayed Click on Yes Click on IP P2P setup Is shown. It is the default port Files are installedClick on Next Field of Max Hops for, input a Click on Find Printers Click on Add Next, installing the printer driverPrinter is added to the Available Printers list INSTALLINGTHEPEER-TO-PEERUTILITY FORIPX/SPX Click on IPX P2P setup Make sure the printer is displayed Under Available Printers Click on Next Files are installedMake sure the printer displayed under Available Printers shows S flag Installation is completed Uninstalling the Peer-to-Peer Utility for TCP/IP Uninstallingthe PEER-TO-PEER Utility Click on OK Restart the computer Uninstalling the Peer-to-Peer Utility for IPX/SPX Click on OK Click on Yes Setup the Print Server Set-up Example NetWare 3.x Setup Select File Server Setting up with PconsoleCreating a print queue Creating the print server Print Server Setup Page Assigning a print queue Enter the priority and press the Enter Key Queue is assigned Available Queues appears Select a created queue Print Server Setup Setting Up Notify Options for the Printer Preferred File Servers Primary File ServerAvailable File Servers list is displayed Press the Esc key to return to the menuPage Setup the Print Server Nwsrv Setup in NDS Mode Starting NetWare Administrator Setting up NetWare AdministratorAdministrator Start NetWare Administrator Printer Click on the container object to create Create Print Queues appears Volume indicated by a in the figurePrint Queue Name Click on Browse of Print Queue Creating the printer Assigning the print queue Click on OK Printer is created Enter the name of the print server Create Print Server windowUnder Print Server Name Details of the created print server Allocating the printer Print server is created Confirmation before setting up Setup in Bindery ModeConfirm Bindery Context Press Alt+F10 to complete the confirmation ORG Starting Pconsole Creating the print server Print Server Information menu Choose the created print serverChoose Printer from the Print Server Information menu and press the Enter Select the created printer and press Printer Xxxxx configurationIs the name of the printer created Enter printer number at Printer No When Exit? appears, choose Yes and press the Enter key When Save Changes? appearsPress the Esc key twice Press the Esc key four times Problems and press Enter key When a message appears, press the Enter keyStart the Pconsole utility Select Print Servers in the Available Option menuPage Setup the Print Server Setup in NDS Mode This is performed on the workstation Creating a print queue Enter the name of the print queue Click on Browse Print Queue VolumeUnder Print Queue Name Indicated by a in the figure at Creating the printer Assigning the print queue Click on OK Printer is created Create Print Server window Allocating the printer Supplements Page With Windows NT4.0/2000 Confirming the TCP/IP Print Services Preparation for Setting up Creating a Shared Printer Click on OK Click on Close To the list of Available ports IP address of the printer is addedAdd Printer Wizard Verify that the check box for Select Windows 95 from the list Click on Next Check on Shared \ENGLISH\ESTUDIO\WIN9598\PCL6 Choose Yes or No as necessary, and click on Finish Printer is created Log on to Windows 2000 as a user With Administrator or Power User Select Local printer When Using the TCP/IP PrintingSelect Create a new port and select Standard TCP/IP Port at Type Select Custom and click on Settings Enter PORT1 for the Queue Name Check on Snmp Status Enabled Enter 10001 at Port Number Check on Snmp Status EnabledSelect Raw or LPR under Protocol Drivers for Windows 2000/XP at Copy Click on OK Click on Next Click on Finish Click on Have Disk 100 101 102 When Using the IPPClick on OK Click on Have Disk 103 InstalledSelect the printer driver to be 104 Select the printer driver and select 105Sharing... from the File menu Click on Additional Drivers Insert the printer driver CD-ROM Click on OK 106 107 Click on OK Printer drivers are installed 108 109 Installing the Printer Driver Features of Each Printer Driver Installing the Printer Driver110 111 112 Installation from the CD-ROMInsert the Printer kit CD-ROM into the CD-ROM drive 113 Click on the appropriate Setup forWindows Version Select the Group Number, and click 114 SelectPaper. the Emulation and DefaultSelect the Peer-to-Peer Port, and click On Next Click on Browse 115Select the network printer and click on OK Enter the printer name, and click on Next 116 117 Click on Finish Complete the installationSelect the Program Folder to be Created, and click on Next Windows 95/98/Me Installation by Adding Printer118 Select the network printer and click 119On OK Click on OK Select the printer to be used, and click on Next 120 If necessary, change the Printer name, then click on Next 121Select to print a test page or not, then Windows NT4.0 Click on Start, select Settings, Then click on Printers122 Select how the printer is to be Controlled Select the printer connected to 123Server, and click on OK Select the port added in the Peer-to Insert the CD-ROM included with 124Printer kit into the CD-ROM drive 125 126 Windows 2000/XPDouble-click on Add Printer to start Printer Wizard Next to browse for a printer then 127Server, and click on Next 128 129 130 Copying the PageMaker PPD file 131 Setting the Options Configuration Click on OK to save the settings Selectitems. the installed options for each132 Run the Uninstall.exe Uninstalling the Printer Driver133 After programs have been removed 134 Install Agfa Font Manager 135 Checkinstall. the components you want to Click on OK Click Finish 136 137 Uninstall Agfa Font Manager 138 Description of Screen Getting Started with Agfa Font Manager 140 141 For Macintosh 142 System RequirementSystem Requirements 143 Copying the PPD File 144 Select the DriverClick on the Apple menu, and select Chooser Make sure that Active is selected for AppleTalk 145 Option Setup Exit the Chooser 146 147 Printer Specific OptionsPrinter Specific Options ➀ Offset Stack ➁ Toner Saving ➃ Duplex 148➄ Media Type ➅ Edge Smoothing 149 Printer Specific Options ➇ Resolution 150 151 Netpanel Function 152 Installing Netpanel 153 InstallingClick on a language of your Operating 154 Click on Setup utilities Click on Netpanel setup Enter the IIS virtual directory 155 Decide whether to read the Readme file at this time 156 157 Uninstalling 158 Required Environments Starting Netpanel159 160 Browsing with NetPanel 161 Log 162 Description of Screen➀ Logo ➁ Topic bar ➂ Task bar 163 Using HelpClick on the Help button on Control bar Open the Window and display Help For the Normal User Operating Flow164 Log Printer Discovery 165 For the Administrator Printer Management 166 167 NetPanel SettingServer Management Group Management Printer Discovery Main Printer Discovery168 169 Searching Result Display➀ System Properties ➁ Connection Properties 170➂ Status Diagnose ➃ Search Result List Printer Management Search Printer Management171 Printer Management Main ➀ Reset Printer172 ➂ NIC Configure ➁ Printer Configure173 ➄ Device Password ➃ Novell Configure174 175 Reset Printer and Test Print Click on Reset Printer Now Operating result is displayed Reset a Printer and NIC176 Select the printer that you want to Print a Test Clickbar. on Reset Printer on the Task Select desired test177 General Properties Printer Configure178 Input Tray Properties ➀ Select Default Input Tray179 ➁ Top Priority Cassette 180 Output Bin Properties Paper Properties ➁ Default Paper Size181 ➀ Copies 182 Printer Setting Properties➀ Lines Per 183 ➉ Print Postscript Error ➈ Emulation SettingDevice Password 184 185 PCL Font Properties 186 Group Management Protocols Configuration NIC Configure187 188 IP Configuration 189 Apple Talk Configuration➀ Printer Name ➁ Zone Name 190 System Configuration➀ Frame Type ➁ LPD Banner ➂ Print on Startup 191➃ Type of Startup Novell Configuration Novell Configure192 Device Password Device Password193 Server Management Main Server Management194 ➀ Printers shared in Windows NT Server 195 Server Management Main Page of Windows NT Server 196 Install a Printer to a File Server 197 Printer is installed to the FileServer 198 Remove a Printer from a File ServerSelect or specify the printer Click on Continue Printer is removed from the File 199 200 Deleting Print Jobs 201 Selected print jobs are canceled Group Management Main Group Management202 203 Create a Group 204 Delete a Group 205 View Group and PrinterClickbar. on View Group on the Task Select a group and click on OK Display the printer properties page or 206Printer status 207 Add a Printer to a Group 208 Remove a Printer from a GroupRemove from the list 209 NetPanel Setting Main Netpanel Setting210 Change the Administrator Password Administrator Setting211 212 WNP Setting 213 Discovery Setting 214 215 MAP MAP Password for MAP216 217 Install MAPClick on a language of your Operating System 218 Click on MAP setup 219 Start MAP Click on MAP Setup in the Map folder220 Select Programs from Start menu 221 Network Administrator page is Displayed 222 Network Administrator page isRun the WWW Browser Enter http//xxx.xxx.xxx.xxx/ at 223 Select Setup NetWare from Network AdministratorEnter each field that applies Click on Accept Setting Enter the password224 225 Select Setup AppleTalk from Network AdministratorDisplayed Network Interface Card is automatically restarted Click on Factory Defaults Restore Factory DefaultsEnter the password and click on Restore Factory Defaults Factory defaults are restored Restart the printer 227 Troubleshooting 228 Netpanel Error 229 Error messages 230 231 When Printing Cannot be Performed 232 233 Specifications and Other Information 234 Specifications of the Units Demo Test Print Sample235 236 Configuration 237 NIC Status 238 PCL Font List 239 240 241 PS Font List 242 243 Status Log 244 Group Management List 245 List of Internal PCL Fonts 246 247 List of Internal PS Fonts 248 E1-17089B Kanda NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8442, Japan