E6581741

Instance 2 Attribute

 

 

 

 

Instance

Attribute ID

Access

Name

Data type

Details

 

1

Get

Interface Speed

UDINT

Interface speed currently in use

 

 

 

 

 

0: indeterminate (Auto baudrate)

 

 

 

 

 

10: 10Mbps

 

 

 

 

 

100: 100Mbps

 

2

Get

Interface Flags

DWORD

Bit 0: Link Status Indicates whether or not the

 

 

 

 

 

Ethernet 802.3 communications

 

 

 

 

 

interface is connected to an active

 

 

 

 

 

network. 0 indicates an inactive link; 1

 

 

 

 

 

indicates an active link.

 

 

 

 

 

Bit 1: Half/Full Duplex Indicates the duplex

 

 

 

 

 

mode currently in use. 0 indicates the

 

 

 

 

 

interface is running half duplex; 1

 

 

 

 

 

indicates full duplex.

 

 

 

 

 

Bit 2-4: Negotiation Status

 

 

 

 

 

000 : Auto-negotiation in progress.

 

 

 

 

 

001 : Auto-negotiation and speed detection

 

 

 

 

 

failed.

 

 

 

 

 

010 : Auto negotiation failed but detected

 

 

 

 

 

speed. Duplex was defaulted.

 

 

 

 

 

011 : Successfully negotiated speed and

 

 

 

 

 

duplex.

 

 

 

 

 

100 : Auto-negotiation not attempted. Forced

 

 

 

 

 

speed and duplex.

2

 

 

 

 

Bit 5: Manual Setting Requires Reset. 0

 

 

 

 

indicates the interface can activate

 

 

 

 

 

changes to link parameters

 

 

 

 

 

(auto-negotiate, duplex mode, interface

 

 

 

 

 

speed) automatically. 1 indicates the

 

 

 

 

 

device requires a Reset service be

 

 

 

 

 

issued to its Identity Object in order for

 

 

 

 

 

the changes to take effect.

 

 

 

 

 

Bit 6: Local Hardware Fault.

 

 

 

 

 

0 indicates the interface detects no local

 

 

 

 

 

hardware fault

 

 

 

 

 

1 indicates a local hardware fault is

 

 

 

 

 

detected. The meaning of this is

 

 

 

 

 

product-specific.

 

 

 

 

 

Bit 7-31(System reserved)

 

3

Get

Physical Address

ARRAY of

MAC layer address

 

 

 

 

6 USINTs

 

 

6

Get/Set

Interface Control

STRUCT

Configuration for physical interface

 

 

 

 

of

 

 

 

 

 

 

 

 

Control Bits

WORD

Interface Control Bits

 

 

 

Forced Interface

UINT

Speed at which the interface shall be forced to

 

 

 

Speed

 

operate

 

7

Get

Interface Type

USINT

Type of interface: twisted pair, fiber, internal,

 

 

 

 

 

etc.

 

10

Get

Interface Label

SHORT_S

Human readable identification

 

 

 

 

TRING

5, Right

Note: Don’t use the “System reserved” bit and Bit0 for the judgement.

Instance Services

 

Service Code

Service Name

Description of Service

0x01

Get_Attribute_All

Read all attributes

0x0E

Get_Attribute_Single

Read one attribute

0x10

Set_Attribute_Single

Write one attribute

0x4C

Get_and_Clear

Gets then clears the specified attribute

 

 

(Interface Counters or Media Counters).

- 43 -

Page 44
Image 44
Toshiba IPE002Z instruction manual Instance 2 Attribute, Bit 7-31System reserved