„ Inverter operating status 2 FD42, FE42 | Toshiba VF-AS1 guide

efesotomasyon.com -Toshiba inverter,drive,servo,plc

E6581315

Inverter operating status 2 (FD42, FE42)

Inverter status 2 (current status): Communication Number FD42

Inverter status 2 (status immediately before the occurrence of a trip): Communication Number FE42

Bit	Function	0		1	Remarks
0	Control mode switching	Speed control		Torque control
		(Simple posi-
		tioning)
1	Electric Power Counting	Counting		Resetting
	(FE76,FE77) status
2	(Reserved)	-		-
3	(Reserved)	-		-
4	Preliminary excitation	Normal		Operation
5	(Reserved)	-		-
6	(Reserved)	-		-
7	Maximum deceleration forced	Normal		Operation
	stop
8	Acceleration/deceleration	00:Acceleration/deceleration 1			Acceleration/ decelera-
	pattern selection1	01:Acceleration/deceleration 2			tion 1 - 4 can be specified
9	Acceleration/deceleration	10:Acceleration/deceleration 3			by combination of two
	pattern selection2	11:Acceleration/deceleration 4			bits
10	V/Fswitching 1	00: V/F 1			Select V/F 1 - 4 by com-
10		01: V/F 2			bination of two bits
11	V/Fswitching 2				bination of two bits

		10: V/F 3
		10: V/F 3
		11: V/F 4
12	Torque limit switching 1	00: Torque limit 1			Select torque limit 1 - 4
12		01: Torque limit 2			by combination of two
13	Torque limit switching 2	01: Torque limit 2			by combination of two
13	Torque limit switching 2	10: Torque limit 3			bits
		10: Torque limit 3			bits
		11: Torque limit 4
14	Speed gain 1/2	Gain 1		Gain 2	Gain 1: , 
14					Gain 2: , 
					Gain 2: , 
15	(Reserved)	-		-

Inverter operating status 3 (FD49, FE49)

Inverter status 3 (current status): Communication Number FD49

Inverter status 3 (current status): Communication Number FE49

Bit	Function	0	1	Remarks
0 to 11	(Reserved)	-	-
12	Acceleration/deceleration	Not achieved	Achieved	Related parameters
	completion (RCH)			f102
13	Specified speed reach (RCHF)	Not achieved	Achieved	Related parameters
				f101, f102
14 to 15	(Reserved)	-	-

53

Image 54

Toshiba TOSVERT VF-AS1 „ Inverter operating status 2 FD42, FE42, „ Inverter operating status 3 FD49, FE49

Contents

Tosvert VF-AS1 Series RS485 Communication Function E6581315② Read first Safety precautions E6581315 Contents General outlines of the communication function BIT15 BIT8BIT7 BIT0Bit Word Data transmission specifications BIT2 Communication protocol About the handling of received framesMOUBUS-RTU Binary mode 2FH Toshiba Inverter Protocol INV-NO CMD Data transmission format used in Ascii modeData transmission format Data 5bytes Blank 28H Bytes Checksum area INV-NO Data SUM Data transmission format used in binary mode Byte Bytes Command receivedReturned for the 57H W and 50H P commands Sum 1 bytes Checksum not omissible 00H to FFH Norn 2FH Byte 4EH6EH Bytes Transmission format of Block Communication Page Bytes Blank Start Code INV-NO Reads the data with the specified communication number CommandsDummy data is required for this command Block communication Computer Inverter RFE03CR RFE03077BCRPage Transmission errors Format error Data transmission format does not matchCommunication There is no communication number that matches Broadcast communication function VF-AS1 From the computer H = 24d  trip status Examples of the use of communication commandsAscii mode Computer → Inverter Inverter → Computer RFC90CR Examples of Communication programs Input #1,B$ =LENS$ For I=1 to LNext Goto 160 T=TIMER COUNT=TIMER-T If Count 0 then T=TIMERPrint #1,B$ Page End If MSComm1.Output = Text2.Text & Chr13 End SubText2.Text = Text1.Text = End Sub MODBUS-RTU protocol Inverter number  Read command MODBUS-RTU transmission formatCRC 5bytes Blank Command 1 byte Write commandBlank Command 1 byte Text size is 8 bytes fixed Inverter Bit counter = Error codesCRC Generation End Return CRC Inter-drive communication E6581315 QWiring 2-wire RS485 communication Never use pin-7 P11 QWiring 4-wire RS485 communication）Page Parameters relating to the slave side example Proportional control of speed =0.01% Slave 100.00Hz1 00% Slave 100.00Hz 00%90.00Hz 45.00Hz 80.00Hz 40.00Hz Transmission format for inter-drive communication INV-NO 1 byte Inverter number Communication parameters 0OFF MODBUS-RTU Baud rate,  , Parity  Inverter number Master INV To Slave „ Timer Time-out period Computer linkPC → INV INV INV → PC PC → INV Send waiting time ,  Free notesUse this function for the following case PI OFF Commands and monitoring from the computerCommunication commands commands from the computer OFF Brake release B Electric Power quantityForcibly braked Preliminary excitation Braking answer BA Wire RS485 communication FA32 „ AM analog output FA52 „ Terminal board output data FA50„ FM analog output FA51 Output terminal no Specified data output Monitoring from the computer RFD00CRUnit 0.01% N·m Input terminal function selection 9 f119 „ Input terminal board status FD06, FE06RES BIT15 „ Output terminal board status FD07, FE07 „ Inverter operating status 1 FD01, FE01 ST=ON ST=OFF „ Inverter operating status 2 FD42, FE42 „ Inverter operating status 3 FD49, FE49 „ Inverter operating command mode status FD45, FE45 „ Inverter operating frequency mode status FD46, FE46Preset speed operation „ Alarm information monitor FC91 „ Cumulative operation time alarm monitor FE79Bit Specifications Remarks E6581315 „ Inverter model capacity code FB05 Model Data LED setting by communication Parameter Name Range SettingUtilizing panel LEDs and keys by communication „ Block Communication Function for LED Display Ascii LED display data code 00H-1FH are blank Blank Key utilization by communication FA10=0FA10=1 Parameter data EEP ROMPage FE19 Torque command Alarm codeFE02 Frequency command value 01Hz FE29 Input power Tion FE80 Cumulative power on time E6581315 FD50 Light-load high-speed torque 01%FE84 Binary input value option SUB Appendix 1 Table of data codesCan ESC Appendix 2 Response time Response time „ Data transmission time Appendix 3 Compatibility with the communication function VF-A7 Appendix 4 Troubleshooting Appendix 5 Connecting for RS485 communication TXA RXARXB TXB