Appendix 4 Troubleshooting | Toshiba TOSVERT VF-AS1 instruction

efesotomasyon.com -Toshiba inverter,drive,servo,plc

E6581315

Appendix 4 Troubleshooting

If a problem arises, diagnose it in accordance with the following table before making a service call. If the problem cannot be solved by any remedy described in the table or if no remedy to the problem is specified in the table, contact your Toshiba dealer.

Problem				Remedies	Reference

Communication	will	not	take	- Are both the computer and the inverter turned on?
place.				- Are all cables connected correctly and securely?
				- Are the same baud rate, parity and bit length set for every unit on the	Chapter 7
				network?
An error code is returned.				- Is the data transmission format correct?	Section 4.1
				- Is the data transmission format correct?	Section 5.1
				- Does the data written fall within the specified range?	Chapter 9
				- Some parameters cannot be written during inverter operation.	Inverter
				Changing should be attempted when the inverter is in halt.	instruction
					manual
The trip err5 and alarm t				- Check the cable connection and the timer setting.	Section 7.3
occur.
Frequency instructions		from	the	- Is the frequency setting mode selection parameter set to “computer”?	Section 8.1
computer have no effect.
Commands, including the run and				- Is the command mode selection parameter set to “computer”?	Section 8.1
stop commands, from the com-
muter have no effect.
During RS485	communication,			- Is the inverter connected correctly?	Refer	to
an inverter sends back respons-				- Are you sure the receive line and the send line are not in contact with	Appendix
es repeatedly an infinite number				each other?	2.
of times.
A change to a parameter does				Some communication-related parameters do not take effect until the	Chapter 7
not take effect.				inverter is reset. To make them take effect, turn the inverter off tempo-
				rarily, then turn it back on.
The setting of a parameter was				When using the TOSHIBA Inverter Protocol, use the W command to	Section 4.2
changed, but it returns to its				write data into the EEPROM. If you use the P command that writes data
original setting when the inverter				into the RAM only, the data will be cleared when the inverters are reset.
is turned off.

70

Image 71

Toshiba TOSVERT VF-AS1 instruction manual Appendix 4 Troubleshooting

Contents

E6581315② Tosvert VF-AS1 Series RS485 Communication Function E6581315 Read first Safety precautions Contents Bit Word General outlines of the communication functionBIT15 BIT8BIT7 BIT0 BIT2 Data transmission specifications MOUBUS-RTU Communication protocolAbout the handling of received frames Toshiba Inverter Protocol Binary mode 2FH Data Data transmission format used in Ascii modeData transmission format INV-NO CMD 28H Bytes Checksum area 5bytes Blank Data SUM INV-NO Data transmission format used in binary mode Sum 1 bytes Checksum not omissible 00H to FFH Command receivedReturned for the 57H W and 50H P commands Byte Bytes 2FH Byte 4EH6EH Bytes Norn Transmission format of Block Communication Page Bytes Blank Start Code INV-NO Block communication Computer Inverter CommandsDummy data is required for this command Reads the data with the specified communication number RFE03077BCR RFE03CRPage Communication There is no communication number that matches Transmission errorsFormat error Data transmission format does not match Broadcast communication function VF-AS1 RFC90CR Examples of the use of communication commandsAscii mode Computer → Inverter Inverter → Computer From the computer H = 24d  trip status Examples of Communication programs Goto =LENS$ For I=1 to LNext Input #1,B$ Print #1,B$ 160 T=TIMER COUNT=TIMER-TIf Count 0 then T=TIMER Page Text2.Text = Text1.Text = End Sub End IfMSComm1.Output = Text2.Text & Chr13 End Sub Inverter number  MODBUS-RTU protocol CRC Read commandMODBUS-RTU transmission format Text size is 8 bytes fixed Inverter Write commandBlank Command 1 byte 5bytes Blank Command 1 byte End Return CRC Error codesCRC Generation Bit counter = Inter-drive communication Never use pin-7 P11 QWiring 4-wire RS485 communication） E6581315 QWiring 2-wire RS485 communicationPage Parameters relating to the slave side example =0.01% Proportional control of speed 80.00Hz 40.00Hz Slave 100.00Hz 00%90.00Hz 45.00Hz Slave 100.00Hz1 00% INV-NO 1 byte Inverter number Transmission format for inter-drive communication 0OFF Communication parameters MODBUS-RTU Inverter number Baud rate,  , Parity  INV INV → PC PC → INV „ Timer Time-out period Computer linkPC → INV Master INV To Slave Use this function for the following case Send waiting time , Free notes OFF Commands and monitoring from the computerCommunication commands commands from the computer PI OFF Braking answer BA Electric Power quantityForcibly braked Preliminary excitation Brake release B Wire RS485 communication FA32 Output terminal no Specified data output „ Terminal board output data FA50„ FM analog output FA51 „ AM analog output FA52 Unit 0.01% N·m Monitoring from the computerRFD00CR BIT15 „ Input terminal board status FD06, FE06RES Input terminal function selection 9 f119 „ Output terminal board status FD07, FE07 ST=ON ST=OFF „ Inverter operating status 1 FD01, FE01 „ Inverter operating status 3 FD49, FE49 „ Inverter operating status 2 FD42, FE42 Preset speed operation „ Inverter operating command mode status FD45, FE45„ Inverter operating frequency mode status FD46, FE46 Bit Specifications Remarks „ Alarm information monitor FC91„ Cumulative operation time alarm monitor FE79 E6581315 Model Data „ Inverter model capacity code FB05 Utilizing panel LEDs and keys by communication LED setting by communicationParameter Name Range Setting „ Block Communication Function for LED Display Blank Ascii LED display data code 00H-1FH are blank FA10=1 Key utilization by communicationFA10=0 Parameter data ROM EEPPage FE29 Input power Alarm codeFE02 Frequency command value 01Hz FE19 Torque command FE84 Binary input value option Tion FE80 Cumulative power on timeE6581315 FD50 Light-load high-speed torque 01% ESC Appendix 1 Table of data codesCan SUB Response time „ Data transmission time Appendix 2 Response time VF-A7 Appendix 3 Compatibility with the communication function Appendix 4 Troubleshooting Appendix 5 Connecting for RS485 communication TXB RXARXB TXA