Manuals / Toshiba / Computer Equipment / Power Supply

Toshiba TOSVERT VF-AS1 instruction manual E6581315 QWiring 2-wire RS485 communication

Models: TOSVERT VF-AS1 VF-AS1

1 73

Download 73 pages 18.65 Kb

Page 35

Image 35

efesotomasyon.com -Toshiba inverter,drive,servo,plc

E6581315

QWiring (2-wire RS485 communication)

CN1 Pin-4

Pin-5

Pin-8 (Pin-3)

Master

RXD+/TXD+

RXD-/TXD-

Straight

Slave

RXD+/TXD+

RXD-/TXD-

Straight

Slave

RXD+/TXD+

RXD-/TXD-

Straight

Slave

RXD+/TXD+

RXD-/TXD-

Terminating resistance 120Ω-1/2W

* Never use pin-7 (P11).

QWiring (4-wire RS485 communication)）

		Cross	Straight	Straight
CN1	Master	Slave	Slave	Slave
Pin-4	RXA	RXA	RXA	RXA
Pin-5	RXB	RXB	RXB	RXB
Pin-3	TXA	TXA	TXA	TXA
Pin-6	TXB	TXB	TXB	TXB
Pin-8	SG	SG	SG	SG
(Pin-2)
				Terminating resistance
				120Ω-1/2W

*Never use pin-1 (Open) and pin-7 (P11).

*You do not need to connect the master receive lines (pins 4 and 5) or the slave send lines (pins 3 and 6).

Page 35

Image 35

Toshiba TOSVERT VF-AS1 instruction manual E6581315 QWiring 2-wire RS485 communication

Contents

E6581315② Tosvert VF-AS1 Series RS485 Communication FunctionE6581315 Read first Safety precautionsContents Bit Word General outlines of the communication functionBIT15 BIT8BIT7 BIT0 BIT2 Data transmission specificationsMOUBUS-RTU Communication protocolAbout the handling of received frames Toshiba Inverter Protocol Binary mode 2FHData Data transmission format used in Ascii modeData transmission format INV-NO CMD28H Bytes Checksum area 5bytes BlankData SUM INV-NOData transmission format used in binary mode Sum 1 bytes Checksum not omissible 00H to FFH Command receivedReturned for the 57H W and 50H P commands Byte Bytes2FH Byte 4EH6EH Bytes NornTransmission format of Block Communication Page Bytes Blank Start Code INV-NO Block communication Computer Inverter CommandsDummy data is required for this command Reads the data with the specified communication numberRFE03077BCR RFE03CRPage Communication There is no communication number that matches Transmission errorsFormat error Data transmission format does not match Broadcast communication function VF-AS1 RFC90CR Examples of the use of communication commandsAscii mode Computer → Inverter Inverter → Computer From the computer H = 24d  trip statusExamples of Communication programs Goto =LENS$ For I=1 to LNext Input #1,B$Print #1,B$ 160 T=TIMER COUNT=TIMER-TIf Count 0 then T=TIMER Page Text2.Text = Text1.Text = End Sub End IfMSComm1.Output = Text2.Text & Chr13 End Sub Inverter number  MODBUS-RTU protocolCRC Read commandMODBUS-RTU transmission format Text size is 8 bytes fixed Inverter Write commandBlank Command 1 byte 5bytes Blank Command 1 byteEnd Return CRC Error codesCRC Generation Bit counter =Inter-drive communication Never use pin-7 P11 QWiring 4-wire RS485 communication） E6581315 QWiring 2-wire RS485 communicationPage Parameters relating to the slave side example =0.01% Proportional control of speed80.00Hz 40.00Hz Slave 100.00Hz 00%90.00Hz 45.00Hz Slave 100.00Hz1 00%INV-NO 1 byte Inverter number Transmission format for inter-drive communication0OFF Communication parametersMODBUS-RTU Inverter number Baud rate,  , Parity INV INV → PC PC → INV „ Timer Time-out period Computer linkPC → INV Master INV To SlaveUse this function for the following case Send waiting time , Free notes OFF Commands and monitoring from the computerCommunication commands commands from the computer PI OFFBraking answer BA Electric Power quantityForcibly braked Preliminary excitation Brake release BWire RS485 communication FA32 Output terminal no Specified data output „ Terminal board output data FA50„ FM analog output FA51 „ AM analog output FA52Unit 0.01% N·m Monitoring from the computerRFD00CR BIT15 „ Input terminal board status FD06, FE06RES Input terminal function selection 9 f119„ Output terminal board status FD07, FE07 ST=ON ST=OFF „ Inverter operating status 1 FD01, FE01„ Inverter operating status 3 FD49, FE49 „ Inverter operating status 2 FD42, FE42Preset speed operation „ Inverter operating command mode status FD45, FE45„ Inverter operating frequency mode status FD46, FE46 Bit Specifications Remarks „ Alarm information monitor FC91„ Cumulative operation time alarm monitor FE79 E6581315 Model Data „ Inverter model capacity code FB05Utilizing panel LEDs and keys by communication LED setting by communicationParameter Name Range Setting „ Block Communication Function for LED Display Blank Ascii LED display data code 00H-1FH are blankFA10=1 Key utilization by communicationFA10=0 Parameter data ROM EEPPage FE29 Input power Alarm codeFE02 Frequency command value 01Hz FE19 Torque commandFE84 Binary input value option Tion FE80 Cumulative power on timeE6581315 FD50 Light-load high-speed torque 01% ESC Appendix 1 Table of data codesCan SUBResponse time „ Data transmission time Appendix 2 Response timeVF-A7 Appendix 3 Compatibility with the communication functionAppendix 4 Troubleshooting Appendix 5 Connecting for RS485 communication TXB RXARXB TXA