Appendix-Timeclock | Trane Tracer Unit Ventilator, ZN.520 specs

Appendix—Timeclock

To switch the load permanently

OFF, press the key a third time.

[O]appears in the display. To return to automatic (pro-

grammed) operation, press the key a fourth time. Run ¹ appears in the display.

NOTE: The Main Power Disconnect switch is located on the lower right side of the unit behind the right front cabinet panel. It is only used to remove power to the unit for servicing.

UV-SVP01A-EN

67

Image 73

Trane Tracer Unit Ventilator, ZN.520 manual Appendix-Timeclock

Contents

Tracer ZN.520 for Classroom Unit Ventilator Installation Owner Diagnostics Installation of New Units Start-up Procedures Power Up Sequence Tracer ZN.520 Overview General Information General Information Tracer ZN.520 unit controller circuit board Controller Circuit Board Features Service Controller FeaturesTypical Components Peer-to-Peer Communications Communication ConfigurationsIntegrated Comfort System Communication Interface Stand-AloneInteroperability Characteristic End Device SpecificationsStandard End Devices Description Standard End Devices Way Control Valve Time clock Zone sensor Dpdt Control Transformer Specifications Installation and Wiring Binary Inputs Generic/baseboard Heat Binary Output Binary Outputs Analog inputs Analog Inputs Mounting Vertical classroom unit ventilator end pocket Power Wiring Proper zone sensor placement Installing the Wall- Mounted Zone Sensor Optional Humidity and CO2 Sensors Typical Wiring Diagram-Wall Mounted Zone Sensor Typical Wiring Diagram-Unit Mounted Zone Sensor Typical Wiring Diagram-Unit Input and output summary Input/Output Summary Input/Output Summary Configurable parameters ConfigurationCooling source Heating source Binary Outputs1 Binary Inputs1 Binary input summary ConfigurationAnalog Inputs1 Analog input summary End Device Configurations Fan ConfigurationFan configuration ranges Default Discharge air limit ranges Default Valid range Setpoint defaults Default Valid rangeSetpoints Discharge Air Limits Power-Up Control Wait Occupied Bypass TimerMaintenance Timers Unit Identification Tag Location IdentifierWinking Unit Operation Power-UpHeating And Cooling Changeover Logic Occupancy Heat/Cool Changeover logic Cooling Operation Fan Off DelayHeating Operation Fan Operation Face-and-Bypass Damper Operation Valve OperationExhaust fan/damper operation Modulating Valves Water assumption chart Entering Water Temperature SamplingUnit Configuration Temperature Assumed1 DX Operation Economizer OperationElectric Heat Operation Baseboard Heat Operation Output Overrides Filter Status/ Maintenance TimerFan Status Other Modes Simple data sharing application Data Sharing-LonWorks More complex data sharing application Heating And Cooling Changeover Logic Heat/Cool Changeover logic Cooling Operation Valve Operation Entering Water Temperature Sampling Economizer Operation Output Overrides Data Sharing-LonWorks More complex data sharing application Red Service LED TroubleshootingBlack Service Push Button Yellow Comm LED Exit6 Test Procedure Troubleshooting Entering Water Temperature Failure Space Temperature FailureDischarge Air Temperature Limit Outdoor Air Temperature Failure Diagnostics Troubleshooting Translating Multiple Diagnostics Fans Rover service tool Valves stay closed Probable cause Possible Explanation ValvesValves stay open Probable cause Possible Explanation Outside Air Damper DX/Electric HeatOutdoor air damper stays closed Probable cause Explanation Probable Cause Explanation Outdoor air damper stays open Replacing Circuit Boards Tracer ZN.520 Unit Controller Replacement Fan Switch Resistance Values Hardwired Setpoint AdjustmentHardwired Thermistor Values Appendix Binary Configuration Appendix-Binary ConfigurationBinary configuration details Binary input or output Function Effective heat/ cool mode output nvoHeatCool Heat/cool mode input NviHeatCoolAppendix-Unit Operation Unit Operation Based On The Effective HEAT/COOL Output Appendix-Unit Operation Appendix-Data Lists Configuration properties1Data Lists Input/output listing1 Appendix-Timeclock Setting the Time ClockSet the Time and Day Set the Program Override Program Manual Operation Review and Change Programs Appendix-Timeclock Appendix-Location Identifier Location Identifier Location Identifier Location Identifier Trane Company