Manuals / Transition Networks / Computer Equipment / Switch

Transition Networks SISGM1040-162D manual Wiring the Power Inputs

Models: SISGM1040-162D

1 132

Download 132 pages 17.65 Kb

Page 14

Transition Networks

SISGM1040-162D-LR

Wiring the Power Inputs

Please follow the steps below to insert the power wire.

Insert the positive and negative wires into the V+ and V- contacts on the terminal block connector.

Tighten the wire-clamp screws for preventing the wires from loosing.

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

7

Image 14

Transition Networks SISGM1040-162D manual Wiring the Power Inputs

Contents

SISGM1040-162D V1.01 SeptemberFirmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Content Connecting to the Console PortDhcp Server-Port and IP Bindings Dhcp Server-System configurationAbout Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 109 Troubles shooting 112 Technical Specification 113100 110Port Based Vlan Supports 802.1Q Tag Vlan BenefitsVlan GvrpTransition Networks SISGM1040-162D-LR Package Contents Physical Dimension Front PanelLED LED IndicatorsTop View PWRLNK/ACT Off Power input 1 is inactive Green Power input 2 is activePWR2 Wiring the Power Inputs Wiring the Fault Alarm Contact Mounting Installation DIN-Rail MountingTransition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Hardware Installation Installation StepsNetwork Application Ring Application Coupling Ring Application Dual Homing Application Console Management Pin AssignmentLogin in the Console Interface CLI Management Configure parameters Commands LevelFollowing table lists the CLI commands and description ExecCommands Set List System Commands Set System NameSystem Description PasswordSystem Location System ContactIP address Subnet maskHours Full half Port Commands SetPortid 101001000autoValue Enable Disable Trunk Commands Set Valn Vlan Commands SetGroupID Group NamePortNumber Ieee 802.1Q VlanGroupName UntaggedVIDSeconds Spanning Tree Commands Set~61440 Spanning-tree forward Spanning-tree helloTime seconds Stp-path-costAutoTrueFalse QOS Commands SetWeighted-fairstrict TrueFalseIgmp Commands Set Mac / Filter Table Commands Set Snmp Commands SetStrings Community Authentication Password PrivacyV1v2cv3v1v2cv3 Community-stringRead View Name Write View Name Notify View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix View NamePort Mirroring Commands Set RXTXBothWords 802.1x Commands SetPort ID Sec NumberAuthorize Tftp Commands SetDisable reject accept Account SystemLog, Smtp and Event Commands SetClientserverboth Index Email addressDownBoth Sntp Commands SetLink-UPLink SmtpTimezone Start time End timeMinute Ring Commands Set Web-Based Management About Web-based ManagementSystem Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration System Event Log-Syslog Configuration To clear all current events log After configuring, clickApply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR Button to apply the configuration IP SecurityPage User Authentication Button to clean all counts Port StatisticsPort Control To add the port which is focused to Aggregator settingPort Trunk To delete Trunk Group. Select the Group ID and click Aggregator Information State Activity Port state activity will change to PassivePort Mirroring ButtonTo apply the settings Rate LimitingVlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rstp System Configuration Rapid Spanning TreePage Rstp Port Configuration Page To switch to the selected Snmp version mode Snmp ConfigurationSystem Configuration Page Trap Configuration To remove unwanted context name SNMPV3 ConfigurationTo add context name. Click Page To add context name Click QoS Configuration QoS Policy and Priority TypePage Port Base Priority COS ConfigurationTOS Configuration Igmp Configuration Page Ring To apply the configuration Lldp Configuration 802.1X/Radius Configuration SecurityPage 802.1x Port Configuration Misc Configuration MAC Address Table Use the MAC address table to ensure port securityPage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering To reset all configurations to Factory DefaultReset switch to default configuration. Click Default value Save Configuration To save the allTo reboot the system System RebootReboot the switch in software reset. Click Troubleshooting Technical Specification Snmp MIBPer port Link/Activity Green, Speed 1000M Green DramCSMA/CD EMI Lacp IgmpSntp 10/100Base-TX Cable Schematic 10 /100BASE-TX Pin outs10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling