Dram, Csma/Cd | Transition Networks SISGM1040-162D instruction

Transition NetworksSISGM1040-162D-LR


	Packet Buffer	1Mbits

	MAC address	8K MAC address table

	Flash ROM	4Mbytes

	DRAM	32Mbytes

		10/100/1000TX: 6 ports RJ-45 with Auto MDI/MDI-X function
	Connector	10/100/1000T/Mini-GBIC Combo: 2 x RJ-45 + 2 x 100/1000
	Connector	SFP sockets
		SFP sockets
		RS-232 interface: RJ-45 type

		10/100/1000Base-T:
		2-pair UTP/STP Cat. 5e/6 cable EIA/TIA-568 100-ohm (100m)
	Network Cable	SFP (Mini-GBIC):
		SFP (Mini-GBIC):
		Multi-mode: 50/125µm~62.5/125µm
		Single-mode: 9/125µm

	Protocol	CSMA/CD

		Per port: Link/Activity (Green), Speed 1000M (Green)
	LED	SFP (Mini-GBIC): Link/Activity (Green)
	LED	Per unit: Power (Green), Power 1 (Green), Power 2 (Green),
		Per unit: Power (Green), Power 1 (Green), Power 2 (Green),
		Fault (Red), Master (Green)

		Input Power Isolation design for Telecom application
	Power Supply	12 ~48 VDC
		Redundant power and removable terminal block

	Power	18 Watts
	Consumption	18 Watts
	Consumption

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

114

Image 121

Transition Networks SISGM1040-162D manual Dram, Csma/Cd, Per port Link/Activity Green, Speed 1000M Green

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content About Web-based Management Preparing for Web Management Dhcp Server-System configurationDhcp Server-Port and IP Bindings Port Mirroring Rate Limiting Vlan configuration 100 Troubles shooting 112 Technical Specification 113109 110 Vlan BenefitsPort Based Vlan Supports 802.1Q Tag Vlan Gvrp Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension Top View LED IndicatorsLED PWR PWR2 Off Power input 1 is inactive Green Power input 2 is activeLNK/ACT Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Following table lists the CLI commands and description Commands LevelConfigure parameters Exec System Name Commands Set List System Commands Set System Location PasswordSystem Description System Contact Hours Subnet maskIP address Portid Port Commands SetFull half 101001000auto Value Enable Disable Trunk Commands Set GroupID Vlan Commands SetValn Group Name GroupName Ieee 802.1Q VlanPortNumber UntaggedVID ~61440 Spanning Tree Commands SetSeconds Time seconds Spanning-tree helloSpanning-tree forward Stp-path-cost Weighted-fairstrict QOS Commands SetAutoTrueFalse TrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set V1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-string ExactPrifix NoAuthNoPrivAuthNoP RivAuthPrivRead View Name Write View Name Notify View Name View Name RXTXBoth Port Mirroring Commands Set Port ID 802.1x Commands SetWords Number Sec Disable reject accept Tftp Commands SetAuthorize Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email address Link-UPLink Sntp Commands SetDownBoth Smtp Minute Start time End timeTimezone Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control Port Trunk Aggregator settingTo add the port which is focused to To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page System Configuration Snmp ConfigurationTo switch to the selected Snmp version mode Page Trap Configuration To add context name. Click SNMPV3 ConfigurationTo remove unwanted context name Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage TOS Configuration COS ConfigurationPort Base Priority Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Reset switch to default configuration. Click Default value Factory DefaultTo reset all configurations to To save the all Save Configuration Reboot the switch in software reset. Click System RebootTo reboot the system Troubleshooting Snmp MIB Technical Specification CSMA/CD DramPer port Link/Activity Green, Speed 1000M Green EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling