Transition Networks SISGM1040-162D specification

Transition Networks

SISGM1040-162D-LR

DHCP Server—System configuration

The system provides the DHCP server function. Enable the DHCP server function, the switch system will be a DHCP server.

DHCP Server: Enable or Disable the DHCP Server function. Enable – the switch will be the DHCP server on your local network.

Low IP Address: the dynamic IP assign range. Low IP address is the beginning of

the dynamic IP assigns range. For example: dynamic IP assign range is from 192.168.1.100 ~ 192.168.1.200. 192.168.1.100 will be the Low IP address.

High IP Address: the dynamic IP assign range. High IP address is the end of the dynamic IP assigns range. For example, dynamic IP assign range is from 192.168.1.100 ~ 192.168.1.200. Therefore, 192.168.1.200 is the High IP address.

Subnet Mask: The dynamic IP assign range subnet mask.

Gateway: The gateway in your network.

DNS: Domain Name Server IP Address in your network.

Lease Time (sec): It is the time period that system will reset the dynamic IP assignment to ensure the dynamic IP won’t have been occupied for a long time; otherwise the server won’t know that the dynamic IP is idle.

And then, click

Apply

DHCP Server Configuration interface

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

50

Image 57

Transition Networks SISGM1040-162D manual Dhcp Server-System configuration

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content Dhcp Server-System configuration About Web-based Management Preparing for Web ManagementDhcp Server-Port and IP Bindings Port Mirroring Rate Limiting Vlan configuration 100 Troubles shooting 112 Technical Specification 113109 110 Vlan BenefitsPort Based Vlan Supports 802.1Q Tag Vlan Gvrp Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension Top View LED IndicatorsLED PWR Off Power input 1 is inactive Green Power input 2 is active PWR2LNK/ACT Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Following table lists the CLI commands and description Commands LevelConfigure parameters Exec System Name Commands Set List System Commands Set System Location PasswordSystem Description System Contact Subnet mask HoursIP address Portid Port Commands SetFull half 101001000auto Value Enable Disable Trunk Commands Set GroupID Vlan Commands SetValn Group Name GroupName Ieee 802.1Q VlanPortNumber UntaggedVID Spanning Tree Commands Set ~61440Seconds Time seconds Spanning-tree helloSpanning-tree forward Stp-path-cost Weighted-fairstrict QOS Commands SetAutoTrueFalse TrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set V1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-string ExactPrifix NoAuthNoPrivAuthNoP RivAuthPrivRead View Name Write View Name Notify View Name View Name RXTXBoth Port Mirroring Commands Set 802.1x Commands Set Port IDWords Number Sec Tftp Commands Set Disable reject acceptAuthorize Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email address Link-UPLink Sntp Commands SetDownBoth Smtp Start time End time MinuteTimezone Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control Aggregator setting Port TrunkTo add the port which is focused to To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page Snmp Configuration System ConfigurationTo switch to the selected Snmp version mode Page Trap Configuration SNMPV3 Configuration To add context name. ClickTo remove unwanted context name Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage COS Configuration TOS ConfigurationPort Base Priority Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Factory Default Reset switch to default configuration. Click Default valueTo reset all configurations to To save the all Save Configuration System Reboot Reboot the switch in software reset. ClickTo reboot the system Troubleshooting Snmp MIB Technical Specification Dram CSMA/CDPer port Link/Activity Green, Speed 1000M Green EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling