Wiring the Fault Alarm Contact | Transition Networks SISGM1040-162D

Transition Networks

SISGM1040-162D-LR

Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. The switch will provide local indication of a power or port failure, if configured, by opening the relay contacts. The following illustration shows an application example for wiring the fault alarm contacts.

Insert the wires into the fault alarm contacts (No. 3 & 4)

NoteThe wire gauge for the terminal block should be in the range between 12~ 24 AWG.

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

8

Image 15

Transition Networks SISGM1040-162D manual Wiring the Fault Alarm Contact

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content Dhcp Server-System configuration About Web-based Management Preparing for Web ManagementDhcp Server-Port and IP Bindings Port Mirroring Rate Limiting Vlan configuration 110 Troubles shooting 112 Technical Specification 113100 109 Gvrp BenefitsVlan Port Based Vlan Supports 802.1Q Tag Vlan Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension PWR LED IndicatorsTop View LED Off Power input 1 is inactive Green Power input 2 is active PWR2LNK/ACT Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Exec Commands LevelFollowing table lists the CLI commands and description Configure parameters System Name Commands Set List System Commands Set System Contact PasswordSystem Location System Description Subnet mask HoursIP address 101001000auto Port Commands SetPortid Full half Value Enable Disable Trunk Commands Set Group Name Vlan Commands SetGroupID Valn UntaggedVID Ieee 802.1Q VlanGroupName PortNumber Spanning Tree Commands Set ~61440Seconds Stp-path-cost Spanning-tree helloTime seconds Spanning-tree forward TrueFalse QOS Commands SetWeighted-fairstrict AutoTrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set Community-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings Community View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify View Name RXTXBoth Port Mirroring Commands Set 802.1x Commands Set Port IDWords Number Sec Tftp Commands Set Disable reject acceptAuthorize Index Email address SystemLog, Smtp and Event Commands SetClientserverboth Account Smtp Sntp Commands SetLink-UPLink DownBoth Start time End time MinuteTimezone Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control Aggregator setting Port TrunkTo add the port which is focused to To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page Snmp Configuration System ConfigurationTo switch to the selected Snmp version mode Page Trap Configuration SNMPV3 Configuration To add context name. ClickTo remove unwanted context name Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage COS Configuration TOS ConfigurationPort Base Priority Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Factory Default Reset switch to default configuration. Click Default valueTo reset all configurations to To save the all Save Configuration System Reboot Reboot the switch in software reset. ClickTo reboot the system Troubleshooting Snmp MIB Technical Specification Dram CSMA/CDPer port Link/Activity Green, Speed 1000M Green EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling