System Login | Transition Networks SISGM1040-162D specs

Transition Networks

SISGM1040-162D-LR

System Login

1.Launch the Internet Explorer on the PC

2.Key in “http:// “+” the IP address of the switch”, and then Press “Enter”.

3.The login screen will appear right after

4.Key in the user name and password. The default user name and password are the same as “root”

5.Press “Enter” or ”OK”, and then the home screen of the Web-based management appears as below:

Login screen

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

46

Image 53

Transition Networks SISGM1040-162D manual System Login

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content Dhcp Server-Port and IP Bindings Dhcp Server-System configurationAbout Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 100 Troubles shooting 112 Technical Specification 113109 110 Vlan BenefitsPort Based Vlan Supports 802.1Q Tag Vlan Gvrp Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension Top View LED IndicatorsLED PWR LNK/ACT Off Power input 1 is inactive Green Power input 2 is activePWR2 Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Following table lists the CLI commands and description Commands LevelConfigure parameters Exec System Name Commands Set List System Commands Set System Location PasswordSystem Description System Contact IP address Subnet maskHours Portid Port Commands SetFull half 101001000auto Value Enable Disable Trunk Commands Set GroupID Vlan Commands SetValn Group Name GroupName Ieee 802.1Q VlanPortNumber UntaggedVID Seconds Spanning Tree Commands Set~61440 Time seconds Spanning-tree helloSpanning-tree forward Stp-path-cost Weighted-fairstrict QOS Commands SetAutoTrueFalse TrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set V1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-string ExactPrifix NoAuthNoPrivAuthNoP RivAuthPrivRead View Name Write View Name Notify View Name View Name RXTXBoth Port Mirroring Commands Set Words 802.1x Commands SetPort ID Number Sec Authorize Tftp Commands SetDisable reject accept Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email address Link-UPLink Sntp Commands SetDownBoth Smtp Timezone Start time End timeMinute Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control To add the port which is focused to Aggregator settingPort Trunk To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page To switch to the selected Snmp version mode Snmp ConfigurationSystem Configuration Page Trap Configuration To remove unwanted context name SNMPV3 ConfigurationTo add context name. Click Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage Port Base Priority COS ConfigurationTOS Configuration Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering To reset all configurations to Factory DefaultReset switch to default configuration. Click Default value To save the all Save Configuration To reboot the system System RebootReboot the switch in software reset. Click Troubleshooting Snmp MIB Technical Specification Per port Link/Activity Green, Speed 1000M Green DramCSMA/CD EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling