Troubleshooting | Transition Networks SISGM1040-162D guide

Transition Networks

SISGM1040-162D-LR

Troubleshooting

Verify the switch is using the right power cord/adapter (DC 12-48V), please don’t use the power adapter with DC voltage higher than 48V, or it may damage the switch.

Select the proper UTP cable to construct user network. Please check that is using the right cable. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100 Category 3, 4 or 5 cable for 10Mbps connections, 100

Category 5 cable for 100Mbps connections, or 100 Category 5e/6 cable for

1000Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

Diagnosing LED Indicators: The Switch can be easily monitored through panel indicators, which indicate common problems. Check the switch panel LEDs to assist in identifying problems.

If the power indicator does not light on when the power cord is plugged in, there may be a problem with the power cord. Check for loose power connections, power losses or surges at power outlet. If user still cannot resolve the problem, contact user local dealer for assistance.

If the Industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit, Please check configuration or status.

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

112

Image 119

Transition Networks SISGM1040-162D manual Troubleshooting

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content Dhcp Server-Port and IP Bindings Dhcp Server-System configurationAbout Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 110 Troubles shooting 112 Technical Specification 113100 109 Gvrp BenefitsVlan Port Based Vlan Supports 802.1Q Tag Vlan Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension PWR LED IndicatorsTop View LED LNK/ACT Off Power input 1 is inactive Green Power input 2 is activePWR2 Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Exec Commands LevelFollowing table lists the CLI commands and description Configure parameters System Name Commands Set List System Commands Set System Contact PasswordSystem Location System Description IP address Subnet maskHours 101001000auto Port Commands SetPortid Full half Value Enable Disable Trunk Commands Set Group Name Vlan Commands SetGroupID Valn UntaggedVID Ieee 802.1Q VlanGroupName PortNumber Seconds Spanning Tree Commands Set~61440 Stp-path-cost Spanning-tree helloTime seconds Spanning-tree forward TrueFalse QOS Commands SetWeighted-fairstrict AutoTrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set Community-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings Community View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify View Name RXTXBoth Port Mirroring Commands Set Words 802.1x Commands SetPort ID Number Sec Authorize Tftp Commands SetDisable reject accept Index Email address SystemLog, Smtp and Event Commands SetClientserverboth Account Smtp Sntp Commands SetLink-UPLink DownBoth Timezone Start time End timeMinute Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control To add the port which is focused to Aggregator settingPort Trunk To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page To switch to the selected Snmp version mode Snmp ConfigurationSystem Configuration Page Trap Configuration To remove unwanted context name SNMPV3 ConfigurationTo add context name. Click Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage Port Base Priority COS ConfigurationTOS Configuration Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering To reset all configurations to Factory DefaultReset switch to default configuration. Click Default value To save the all Save Configuration To reboot the system System RebootReboot the switch in software reset. Click Troubleshooting Snmp MIB Technical Specification Per port Link/Activity Green, Speed 1000M Green DramCSMA/CD EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling